The Effect of Adhesion Interaction on the Mechanical Properties of Thermoplastic Basalt Plastics

The effect of temperature, adhesion time, and surface treatment of a reinforcing filler on the mechanical properties of thermoplastic basalt plastics based on a high-density polyethylene and a copolymer of 1,3,5-trioxane with 1,3-dioxolan is investigated. An extreme dependence for the adhesive strength in a thermoplastic-basalt fiber system is established and its effect on the mechanical properties of basalt plastics and the influence of the adhesion contact time on the adhesive strength in the system are clarified. The surface modification of basalt fibers in acidic and alkaline media intensifies the adhesion of thermoplastics to them owing to a more developed surface of the reinforcing fibers after etching. It is found that the treatment in the acidic medium is more efficient and considerably improves the mechanical properties of basalt plastics.     

化纤复丝强度与纤维根数的关系

以单纤维强度服从Weibull分布、纤维束强度服从正态分布条件下纤维束强度与纤维根数间的关系为理论基础，测定分析了实际PET，PA6DTY复丝的平均强度与纤维根数间的关系，得出：复丝内纤维根数增加，复丝的平均强度下降；但当纤维根数增加到一定程度时，由于纤维间的相互作用增大，复丝强度又有所提高．除了强度分布因素外，实际复丝的强度与纤维根数的关系还受到复丝纱线结构、复丝内纤维间相互作用等因素的影响．     

Modulation of absorption and refractive index in Er3 -doped fibers

Modulation of the absorption and refractive index in Er³⁺-doped fibers for a signal wavelength in the 1550-nm band and a pump wavelength of 980 nm is investigated. The experimental results are compared with a model that takes into account optical transitions between the ground state and the metastable state in Er³⁺. Good agreement between the experiment and the model is obtained apart from a wavelength-independent constant in the refractive index modulation, which is discussed.     

Preparation and characterization of a nanoscale poly(vinyl alcohol) fiber aggregate produced by an electrospinning method

Nanoscale poly(vinyl alcohol) (PVA) fiber (100–500 nm) aggregates were prepared with an electrospinning technique. Additionally, a chemical crosslinking method was used to crosslink the nanoscale PVA fiber aggregates. Differential scanning calorimetry, wide‐angle X‐ray diffraction, and scanning electron microscopy techniques were employed to characterize the PVA fiber aggregates. The different crosslinking densities of the PVA fiber aggregates were obtained through the control of the weight percentage of glyoxal to PVA. The crosslinking densities due to heat treatment and chemical crosslinking were studied. The influence of heat treatment could be neglected in contrast to chemical crosslinking when the curing temperature was 120 °C. The primary factor that affected the crosslinking density was the volume of the chemical crosslinking agent. The results showed that the properly crosslinked PVA fiber aggregates had better antiwater solubility and mechanical properties than the noncrosslinked PVA fiber aggregates. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1261–1268, 2002     

Scattering loss in Nd-doped silica based optical fibers

Rare-earth doped fibers suffer from relatively high attenuation in comparison to conventional communication fibers. In order to improve the properties of such fibers, understanding of the mechanisms involved in scattering effects is of great importance. The effect of Nd-doping, Al-codoping and of the drawing temperature on the scattering effect was investigated for several different optical fibers. To this end a measuring setup was realized which allows absolute measurements of the scattering coefficient at different positions along a fiber. Also separation of total attenuation and scattering effects is possible. The presented results indicate scattering effects as primary source for increased attenuation compared with undoped fibers.     

Fibrillation Property of the Lyocell Fibers Treated by N-hydroxymethyl Cross-linking Agents

Lyocell fibers are subject to fibrillate under wet conditions, which severely affects the appearance of this kind of fabrics. Cross-linking treatment is an important way to prevent fibrillation of lyocell fibers. In this study, two kinds of traditional N- hydroxymethyl crosslinking agents were used to treat lyocell fibers and the wet abrasion values of lyocell fibers were measured in a wet abrasion test. The results show the wet abrasion values of lyocell fibers increase with the increasing concentration of the cross-linking agents, which indicates the anti-fibrillation property of the treated fibers has been improved. But the mechanical properties of the treated fibers decreased in some extent. The FT-IR spectroscopy analysis shows that the lyocell fibers have cross-linked with cross-linking agents. The SEM analysis results show the fibers treated by 4% DMDHEU or 5%SECO have good anti-fibrillation properties.     

一种晶体光纤基模色散特性的矢量法分析

利用矢量有效折射率方法(矢量法)对光子晶体光纤基模的色散特性进行了数值模拟，并与双正交归一基矢量法以及标量有效折射率方法(标量法)的模拟结果进行了对比.发现所用矢量法的结果与双正交归一基矢量法的结果符合很好，而标量法在低空气填充率f或较高归一化波数A/λ时是一种较好的近似，在空气填充率f较高或归一化波数A/λ较低时，要得到精确的结果必须利用矢量法对光子晶体光纤的特性进行模拟.讨论了光子晶体光纤包层有效折射率与光纤结构的关系. 关键词： 光子晶体光纤 矢量法 有效折射率 色散     

连续碳纤维增强聚醚砜复合材料的形态与力学性能

研究了PES/碳纤维复合材料的力学性能与树脂含量的关系,并用SEM观察了复合材料冲击断面的形貌。提出了一个模糊评价法,可定量表征复合材料的界面粘合性。     

Electrospinning of ultrahigh‐molecular‐weight polyethylene nanofibers

The electrospinning method has been employed to fabricate ultrafine nanofibers of ultrahigh‐molecular‐weight polyethylene for the first time with a mixture of solvents of different dielectric constants and conductivities. The possibility of producing highly oriented nanofibers from ultrahigh‐molecular‐weight polymers suggests new ways of fabricating ultrastrong, porous, and single‐component nanocomposite fibers with improved properties. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 766–773, 2007     

Analytical design of photonic band-gap fibers and their dispersion characteristics

The paper essentially deals with the analysis of photonic band-gap fibers in analogy with the electron wave motion in periodic crystal lattice. As such, the analyses are based on Bloch formulation. The dispersion characteristics of such fibers are presented by considering some illustrative values of design parameters. The effect of design parameters on the dispersion characteristics is also presented in terms of the variation of widths of allowed and forbidden bands of band-gap fibers. It is found that the number of allowed bands increases with the increase in difference between refractive indices of different layers. Further, widths of the allowed and forbidden bands increase with the increase in layer thickness.