强激光与固体靶作用产生的表面电子加速和辐射研究

利用单电子在固体靶表面准静态电磁场中运动的模型和非线性汤姆孙散射理论,研究了以大角度斜入射的强激光照射在固体靶表面产生的沿靶面方向发射的高能超热电子的运动及其产生的电磁辐射脉冲. 数值模拟表明,靶表面的电子在靶面附近的准静态电磁场和反射的激光场中作振荡. 当电子振荡频率接近激光频率时,电子被有效加速,被加速的电子主要沿靶面方向运动并产生向前的阿秒脉冲辐射. 讨论了电子在加速前的不同初始速度分布对辐射脉冲的时间和空间特性的影响,模拟了不同初始状态的多电子相干辐射脉冲的频谱特性. 关键词： 表面准静态电磁场 超热电子 阿秒脉冲 相干辐射     

一种以压力一维均匀分布为特征的长条形对顶压砧

针对圆形端面平面对顶压砧装置中压力梯度大的问题, 本文设计了一种长条形端面的平面对顶压砧, 相应的封垫也改为长条形. 原理分析表明: 这种压砧可在沿长条形中心线的狭长区域内产生均匀分布的高压力. 本文采用长20 mm宽5 mm长条形端面的硬质合金压砧配合叶腊石封垫进行压力标定, 实验结果显示: 这种装置可产生10 GPa以上的高压, 在长条形中心线上至少12 mm长度范围内的不同位置上产生的压力基本一致, 在2.55 GPa压力时测量偏差小于2.0%, 在7.7 GPa时测量偏差小于3.6%. 这种特点很有利于对细长样品进行精确的高压物性测量.     

红外用CVD ZnS多晶材料的研制

论述了制备红外用CVD ZnS多晶材料的化学气相沉积工艺和热等静压处理工艺。针对CVD ZnS多晶材料具备优良的光学和力学性能,采用化学气相沉积工艺和热等静压处理技术成功研制出大尺寸多晶材料,其最大尺寸达到250mm×15mm。测试了CVD ZnS样品的各项光学、力学性能指标。样品的全波段透过率均接近ZnS材料的本征水平,折射指数均匀性优于2×10^-5,在1.06μm的吸收系数为2×10^-3cm^-1,抗弯强度达到104MPa。     

The Influence of the Renormalization Condition to the Equation of State of the Nuclear Matter

In the relativistic σ-ω model, the influences of the parameters b, c, d in the potential U(σ)=(1/2!)bσ²+(1/3!)cσ³+ (1/4!)dσ⁴ to the incompressibility, effective mass and binding energy of the nuclear matter are studied in detail. The calculation of equation of state of nuclear matter shows that the values of b, c, d depend on the renormalization condition, we also find that a soft equation of state of nuclear matter can be obtained in a suitable renormalization condition, and the experimental incompressibility coefficient can be reproduced. These results are also used to study the thermal properties of hot Δ-resonant nuclear matter.     

宽频带光束非线性热像效应的实验研究

实验研究宽频带脉冲光束通过非线性介质时的非线性热像的形成过程,揭示了光束入射功率和脉冲宽度、介质厚度等因素对热像光强和位置的影响. 结果表明,与单纵模激光束一样,在宽频带脉冲光束情形下,非线性介质上游元件的模糊斑调制也可导致在下游共轭位置形成热像. 热像光强随入射光束功率的增加而增加;若脉冲能量一定,则热像光强随脉冲宽度的增加而减弱;若脉冲峰值功率一定,则热像光强随脉冲宽度的增加而增强. 关键词： 高功率激光 热像 宽带光束 小尺度自聚焦     

紫外单光子成像系统增益特性研究

介绍了基于微通道板和楔条形阳极的紫外单光子成像系统的组成和工作原理.利用该系统分别研究了两块和三块微通道板在不同电压下的暗计数特性.实验和拟合结果表明微通道板的暗计数脉冲幅度呈负指数型分布,暗计数率随电压升高而增大.通过测试不同电压下的脉冲幅度分布曲线,发现微通道板增益在较高电压下更加均匀.研究了两块微通道板情况下,微通道板电压和间距对系统分辨率的影响.结果表明,系统分辨率随微通道板电压增加而提高;另外,适当增加微通道板间距也可以提高系统分辨率. 关键词： 单光子计数成像 微通道板 楔条形阳极 分辨率     

大长径比熔铸装药热芯棒凝固工艺优化仿真

为提高大长径比战斗部的熔铸装药质量,采用有限元仿真方法建立了三维装药模型,对熔铸装药过程进行数值模拟。通过分析传统铸装和热芯棒工艺铸装的仿真结果,结合缩孔形成原因和传统热芯棒工艺对装药质量的改善机理,设计出一种多层次优化温度控制的热芯棒,并对改良热芯棒工艺铸装过程进行数值模拟,预测热芯棒改良工艺对装药质量的影响。结果表明:传统热芯棒铸装工艺无法改变药柱径向凝固顺序,在药室宽大处仍然会出现缩孔缩松的疵病,而改良热芯棒工艺通过改善药柱凝固顺序,可以预防缩孔缩松出现,达到了预期要求。     

Theory of the transmission of metal strip gratings on a dielectric substrate application to submillimeter laser coupling

The advantages of supported metal strip gratings with respect to free-standing metal meshes are pointed out for applications as laser output couplers. A new, simple formula for the power transmission through the strip grating on a dielectric plate is derived from a line equivalent-circuit model. This formula is in good agreement with measurements performed on several samples, at different submillimeter wavelengths. An application to output couplers of far-infrared gas discharge lasers allows to improve the reliability of such lasers.x Unité associée au CNRS. U.A. 836.     

Fabrication and surface enhanced Raman spectroscopy of single Au@SiO2 dimers linked by benzenedithiol

Metal nanoparticle dimers with controllable gap distance have attracted considerable attention because of their promising application in plasmonics. Generally, gaps with nanometer or subnanometer dimensions generate localized surface plasmon resonance (LSPR) coupling effect, thus contributing to a strong electromagnetic field for improving surface enhanced Raman scattering (SERS) effect. Here, we developed a facile approach to fabricate Au@SiO₂ dimers through the steric hindrance effect, in which the SiO₂ shell functioned as a block and a rigid dithiol molecule was employed as linker. The thickness of the SiO₂ shell played a critical role in improving the yield of dimers. The dimerization efficiency increased significantly as the shell thickness decreased to ~1 nm. When 1,4‐benzenedithiol was used as linker molecule, the yield of dimers was ~30%. Few dimers were obtained when mecaptobenzonic acid was used as linker. A thicker shell is associated with a low yield of dimer, whereas a thinner shell resulted in the formation of multimers and linear structures. The low number of linker molecules on the exposed area of monodisperse single nanoparticles and the lack of LSPR coupling effect (‘hot spots’) resulted in the disappearance of SERS signals of the linkers. The estimated SERS enhancement factor was about eight fold because of the strong coupling effect in the gap of the dimer with the distance of the dithiol molecular length. From the above results, SERS combined with SEM could be developed into powerful tools for monitoring the formation of dimers and positioning of single dimers. It may aid the control of assembly of Au nanoparticles and in probing key issues about SERS enhancements. Copyright © 2015 John Wiley & Sons, Ltd.     

Raman and IR spectroscopy study of corrosion products on the surface of the hot‐dip galvanized steel with alkaline mud adhesion

The corrosion products formed on hot‐dip galvanized steel sheets for the automobile application with adhesion of alkaline mud containing different Cl⁻ ion contents are investigated by means of Raman and infrared (IR) spectroscopy. Results show that the Cl⁻ ion content in alkaline mud has great influence on the corrosion behavior of the galvanized steel. The Cl⁻ ions are responsible for the formation of the Zn₅Cl₂(OH)₈· H₂O layer on the surface of the steel at the early stage of corrosion. The rest of the Cl⁻ ions then penetrate and interrupt corrosion product layer resulting in pitting corrosion. Subsequently, the red corrosion product of α‐FeOOH (shaped as needle‐like structure) is formed, which then transforms into black rust of Fe₃O₄ (having a shape of slim needle). It is interesting to find out that pitting depth is inversely proportional to the Cl⁻ ion content. However, corrosion rate decreases with the increase of the Cl⁻ ions in mud. Copyright © 2009 John Wiley & Sons, Ltd.