高精度的光纤衰减系数测试系统的设计

利用常规仪器设备，设计了一套集光、机、电为一体的光纤衰减测量,实现了数字化监测显示，并可与微机接口；采用双光路法，消除了由于光源光强不稳定产生的误差。     

Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

An ASE Reduction Filter Using Cascaded Optical Fiber Grating Couplers in EDFA Repeater

A new configuration for an ASE reduction filter in EDFA repeaters for WDM optical transmission systems using optical fiber grating couplers (FGCs) was proposed and first demonstrated. The filtering characteristics of the proposed filter for amplified single wavelength signal and 2-channel WDM signals using EDFA were identified. It was found that the filter was effective to improve SNR in optical domain by reducing ASE noise. The required FGC characteristics for the filter were theoretically predicted under the condition that the total filter loss did not exceed 3 dB. More than 70% of drop efficiency was required in each FGC for the application of the proposed filter to an 8-channel WDM system using EDFA repeaters.     

自平衡式单臂双用扭矩定标器

本文指出了当前在科研和生产中采用的一般机械式扭矩加载器的某些缺点和错 误；提出一种自平衡式单臂双用纯扭矩加载装置，可以消除定标过程的附加干扰，保 证检测精度。该装置简单，合理、适用。     

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayers

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayer (ML) up to 600 °C have been studied and reported in this paper. Ti/Ni multilayer samples having constant layer thicknesses of 50 Å each are deposited on float glass and Si(1 1 1) substrates using electron-beam evaporation technique under ultra-high vacuum (UHV) conditions at room temperatures. The micro-structural parameters and their evolution with temperature for as-deposited as well as annealed multilayer samples up to 600 °C in a step of 100 °C for 1 h are determined by using X-ray diffraction (XRD) and grazing incidence X-ray reflectivity techniques. The X-ray diffraction pattern recorded at 300 °C annealed multilayer sample shows interesting structural transformation (from crystalline to amorphous) because of the solid-state reaction (SSR) and subsequent re-crystallization at higher temperatures of annealing, particularly at ≥400 °C due to the formation of TiNi₃ and Ti₂Ni alloy phases. Sample quality and surface morphology are examined by using atomic force microscopy (AFM) technique for both as-deposited as well as annealed multilayer samples. In addition to this, a temperature dependent dc resistivity measurement is also used to study the structural transformation and subsequent alloy phase formation due to annealing treatment. The corresponding magnetization behavior of multilayer samples after each stage of annealing has been investigated by using Magneto-Optical Kerr Effect (MOKE) technique and results are interpreted in terms of observed micro-structural changes.     

等效可变孔径远场法测量单模光纤模场半径

本文提出等效远场的可变孔径方法,由测量光纤远场累积分布求得模场半径。并且利用Petermann关于模场半径的新定义,推出了一种对非高斯模场分布也适用的求模场半径的方法。实验表明,这种测量方法简便可靠,在不同的制备端面下,重复测量的标准误差小于0.04μm。     

Liquid phase oxidation of p-chlorotoluene to p-chlorobenzaldehyde over cobalt-doped mesoporous titania with a crystalline framework

Cobalt-doped mesoporous titania with a crystalline framework synthesized by surfactant templating method presented highly selective (99%) and reasonable conversion rate (49%) of catalytic oxidation of para-chlorotoluene to para-chlorobenzaldehyde in acetic acid using aqueous hydrogen peroxide as oxidant for the first time. Recycling of the catalyst indicates that the catalyst can be used a number of times without losing its activity to a greater extent. By contrast, cobalt-doped mesoporous titania without a crystalline structure and cobalt doped the commercial titania, Degussa P25 prepared by impregnation method with the similar concentration of cobalt were found inactive. The effects of catalyst concentration, reaction time, reaction temperature, and solvents on the performance of the catalyst were also investigated.     

Microstructure of laser melted Al18B4O33w/2024Al composite

The microstructure of a laser treated Al₁₈B₄O₃₃w/2024Al composite has been investigated using transmission electron microscope (TEM), low-angle (glancing angle) X-ray diffraction (XRD) techniques. Various surface microstructures were observed in the laser treated composite. The Al₁₈B₄O₃₃ whisker on the surface of the composite was decomposed during laser surface melting, various decomposition products were studied in the laser treated composite. Eutectic phases and the precipitation in the matrix of the composite with laser-treated were observed. The main phases detected in the molten zone were aluminum and decomposition products Al₂O₃. The effect of laser treatment on the hardness of the composite was also examined. A surface hardness of 400 Hv was noted.     

延长光通信传输距离技术探讨

随着光纤传输技术的不断发展,在传输领域中光传输已占主导地位。光纤存在巨大的频带资源和优异的传输性能,是实现高速、大容量传输的最理想的传输媒质。对光纤传输的要求是传的距离越远越好。从光纤传输距离的计算方法入手,结合影响传输距离的几个因素来分析可以从哪些方面入手来延长光纤通信的传输距离。