Determination of the degree of cure under dynamic and isothermal curing conditions with electrical impedance spectroscopy

This article presents a new methodology for the quantitative determination of the progress of the curing reaction of a thermosetting resin, using the results of electrical impedance spectroscopy. The method is an extension of the use of the imaginary impedance maximum as a reaction progress indicator and is based on the demonstration of a close correlation between the reaction rate, as measured by conventional differential scanning calorimetry, and the rate of change of the value of the imaginary impedance spectrum maximum. Tests on a commercial aerospace epoxy resin under both isothermal and dynamic heating conditions with calorimetry and impedance spectroscopy have demonstrated the validity of the method and set the accuracy limits involved. This technique can be used as a real-time online control tool for thermoset composite manufacturing. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 146–154, 2004     

Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Statistical thermodynamics evaluation of polymer–polymer miscibility

The Simha and Somcynsky (S–S) statistical thermodynamics theory was used to compute the solubility parameters as a function of temperature and pressure [δ = δ(T, P)], for a series of polymer melts. The characteristic scaling parameters required for this task, P*, T*, and V*, were extracted from the pressure–temperature–volume (PVT) data. To determine the potential polymer–polymer miscibility, the dependence of δ versus T (at ambient pressure) was computed for 17 polymers. Close proximity of the δ versus T curves for four miscible polymer pairs: PPE/PS, PS/PVME, and PC/PMMA signaled the usefulness of this approach. It is noteworthy, that the tabulated solubility parameters (derived from the solution data under ambient conditions) propounded the immiscibility of the PVC/PVAc pair. The computed values of δ also suggested miscibility for polymer pairs of unknown miscibility, namely PPE/PVC, PPE/PVAc, and PET/PSF. In recognizing the limitations of the solubility parameter approach (the omission of several thermodynamic contributions), these preliminary results are auspicious because they indicate a new route for estimating the miscibility of any polymeric material at a given temperature and pressure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2909–2915, 2004     

The exponential power law: partial wetting kinetics and dynamic contact angles

An equation for the kinetics of partial drop spreading is proposed. This equation was empirically derived from experimental data for the spreading kinetics of partially wetting liquids in terms of the wet area versus time. The equation has the form of an exponential power law (EPL), and transforms into the well-known power law for complete wetting, when the equilibrium contact angle approaches zero. The EPL fits very well available experimental data. To lend additional support to the validity of this generalized equation, it will be demonstrated that when it is transformed to present the dynamic contact angle (DCA), it fits very well DCA experimental data for other wetting processes, such as capillary flow and tape coating.     

爆磁压缩发生器通过脉冲变压器对脉冲形成线充电的理论分析

 将爆磁压缩等效为电流源的方法，对爆磁压缩发生器通过脉冲变压器对脉冲形成线充电进行了理论分析，得出爆磁压缩发生器在负载上产生电流波形（简称负载电流）为直线情况和任意电流波形情况下充电电流和充电电压的表达式。分析表明变压器耦合互感与负载电流随时间变化增长率是脉冲形成线充电的两个重要参数，脉冲形成线第一个充电电压峰值与变压器的耦合互感和负载电流波形斜率成正比，负载电流波形斜率的变化可以改变充电电压峰值的时间，斜率不断增加可以延长第一个充电电压峰值时间，从而可能增加充电电压的幅值，提高爆磁压缩发生器能量的利用效率。     

论壮汉语s-与t-的对应

壮语里t-(t‘-)>s-的音变现象是存在的,不论是汉语,或者是壮语,它们的内部或两者之间都存在着s-与t-(t‘-)对应的规律。     

因素空间理论与知识表示的数学框架(XⅢ)──描述架中概念的结构(2)

本文是［１，１２］的继续，研究描述架中概念的结构；本文讨论后半部分，内容涉及概念内涵与外延的转换，清晰关系的内投影与内变换，概念的结构＊以及有关问题的注记。     

边界拟合坐标系中的流动方程

本文提出了流体力学解析边界拟合坐标系方法，及建立在这种坐标系基础上对流动方程进行摄动处理的方法，并列举几种流动建立了解析边界拟合坐标系中的方程。     

一类对称的Kolmogorov系统的定性研究（Ⅰ）

本文对一类对称的三次微分系统进行探讨，对每个奇点导出表示其鞍结性的型号公式。给出（Ｋ３）所有的六种全局相图。     

On a Question of Phillips

In [5] Phillips proved that one can obtain the additive group of any nonstandard model *? of the ring ? of integers by using a linear mod 1 function h : F ?, where F is the α-dimensional vector space over ? when α is the cardinality of *?. In this connection it arises the question whether there are linear mod 1 functions which are neither addition nor quasi-linear. We prove that this is the case.