Cure Behavior and Thermal Properties of Poly (Amide-Amidic Acid) Modified Diglycidyl Ether of Bisphenol-A/4,4′-Diaminodiphenylsulfone

Poly (amide-amidic acid) (PAA) was selected to modify diglycidyl ether of bisphenol-A (DGEBA)/4,4′-diaminodiphenylsulfone (DDS). The cure behavior was studied by means of nonisothermal differential scanning calorimeter (DSC) analysis, indicating that PAA played a role of catalyst during the process of the curing reaction. Results of Fourier transform infrared spectroscopy (FT-IR) analysis showed that the PAA acted as a co-curing agent when the PAA content was 3.2–38.4 phr and also as a modifier when the PAA content was 12.8–38.4 phr. The glass transition temperature (T_g ) decreased with the increase of PAA content. The thermal stability improved when the PAA content was 3.2–6.4 phr because of the catalytic effect of PAA. The flexural strength improved for the varying PAA content studied in this work, with the highest flexural strength being obtained when the PAA content was 6.4 phr. The fracture surface morphology was observed using scanning electron microscopy (SEM); the morphologies varied with changing content of PAA.     

FCSR新型管幕构件抗弯性能试验研究及数值分析

基于翼缘板-槽钢连接的新型管幕构件(flange-channel steel roof，FCSR)室内抗弯试验，研究了FCSR新型管幕构件的工作机理和破坏模式.为充分研究钢管壁厚、翼缘板厚度、混凝土强度和钢管间距等结构关键参数对FCSR管幕构件抗弯性能的影响，通过ABAQUS软件建立了FCSR管幕构件的有限元模型.研究结果表明:构件发生明显的延性破坏，具有较高的横向刚度；钢管壁厚和混凝土强度对构件承载力具有一定的影响，翼缘板厚度对承载力影响不明显，钢管间距对承载力影响较为明显.研究结果可为新型管幕结构的应用提供一定的依据.     

氧化石墨烯增强环氧树脂复合材料的制备及其力学性能研究

以天然石墨为原料，利用改进的Hummers法制备氧化石墨烯，并对其进行X-射线衍射（XRD）和傅里叶变换红外光谱（FT-IR）表征。之后利用一种新型的有机溶剂三缩水甘油基对氨基苯酚（TGPAP）作为相转移剂和表面活性剂，将氧化石墨烯（GO）从水溶液转移到环氧树脂基体中，去除水分，加入固化剂进而得到混合液，最后利用浇铸法得到复合材料。通过万能测试拉力机对复合材料的拉伸性能和弯曲性能进行测试，结果表明氧化石墨烯的加入能够有效增强复合材料的力学性能：在添加0.1%（质量分数）的氧化石墨烯时，复合材料拉伸强度达到最大值77.29 MPa，与不添加氧化石墨烯相比提高了26.60%；在添加1.0%的氧化石墨烯时，拉伸模量达到最大值2 451.99 MPa，与纯环氧树脂相比提高了21.69%。     

纳米银改性树脂基托机械性能的初步研究

采用磁控溅射技术在聚甲基丙烯酸甲酯(PMMA)树脂基托表面沉积一层纳米银(Ag NPs)涂层.研究了纳米银改性PMMA树脂基托的机械性能,为改性材料的临床应用提供理论基础.根据国际标准ISO2409:2007描述的划格法对涂层与基底的附着力强度进行测试,各组试件的接触角采用静态液滴法测量,三点弯曲法检测试件的弯曲强度.结果显示,各组涂层与PMMA基底材料结合良好,各组试件的表面润湿性变化不大,其中PMMA-Ag NPs80s组疏水性略有提高,各组试件的弯曲强度均符合国家标准.     

不同活性掺合料RPC力学性能试验研究

为了研究不同活性掺合料的活性粉末混凝土(RPC)在不同养护温度条件下的基本力学性能,分别对24组不同养护温度、不同活性掺合料的RPC试件,进行抗压强度和抗折强度试验。结果表明:同一种活性掺合料替代硅灰比例相同时,高温养护条件下的RPC试件力学性能优于常温养护条件下的RPC试件;在相同温度下,不同活性掺合料替代硅灰比例为40%~60%时,RPC试件抗压强度大小依次为:粉煤灰微硅粉石英砂;活性掺合料种类和替代硅灰比例的改变对RPC试件抗折强度影响不是很大;钢纤维的掺入对RPC试件的强度有一定的提高作用。     

燕尾榫样式对CFRP加固榫卯接长木梁抗弯性能影响试验

通过11根木梁的静力受弯试验,研究燕尾榫样式对榫卯接长木梁加固后的抗弯性能的影响.试验结果表明,未加固前榫卯接长木梁承载力较低,仅为完整木梁的1.00%~2.62%,经CFRP布加固后其抗弯承载力可提高至完整木梁的50%~83.33%;旋转90°后,传统燕尾榫进行榫卯接长和采用榫头带榫肩接长,其抗弯承载力和能量吸收能力提高.燕尾榫榫头斜率从0.1变化至0.3,木梁的抗弯承载力和能量吸收能力随之提高,其抗弯承载力分别可达完整木梁的71.43%~83.33%,能量吸收能力分别达完整木梁的43.01%~61.33%.当燕尾榫榫头长度超过传统燕尾榫榫头长度时,其抗弯承载力、能量吸收能力和刚度反而降低.     

一种多频局域共振型声子晶体板的低频带隙与减振特性

设计了一种多频局域共振型声子晶体板结构, 该结构由一薄板上附加周期性排列的多个双悬臂梁式子结构而构成. 由于多个双悬臂梁式子结构的低频振动与薄板振动的相互耦合作用, 这种局域共振型板结构可产生多个低频弯曲波带隙(禁带); 带隙频率范围内的板弯曲波会被禁止传播, 利用带隙可以实现对薄板的多个目标频率处低频减振. 本文针对这种局域共振型板结构进行了简化, 并基于平面波展开法建立了其弯曲波带隙计算理论模型; 基于该模型, 结合具体算例进行了带隙特性理论分析. 设计、制备了一种存在两个低频弯曲波带隙的局域共振型板结构样件, 通过激光扫描测振仪测试证实该结构存在两个低频带隙, 在带隙频率范围的板弯曲振动被显著衰减.     

弯曲型Lamb波传播特性与固井质量相关性研究

轻质水泥在油田固井中的广泛应用使得传统测井方式无法有效的对固井水泥胶结质量做出评价。为了研究新的可行的评价方法,本文采用传递矩阵方法对套管中传播的弯曲型Lamb波进行建模,并通过对所建模型进行数值计算研究了套管外水泥等介质的声学参数变化对弯曲型Lamb波衰减率的影响。数值计算的结果表明,弯曲型Lamb波的衰减率与水泥的声学参数以及水泥与套管的胶结状况有较强相关性,据此可对水泥与套管胶结状况进行评价。本文的计算结果与分析对弯曲型Lamb波在水泥胶结评价中的应用具有一定的参考意义。     

夹芯梁的精确解法

夹芯梁与普通梁的本质区别在于剪切引起芯层横截面严重的而又不均匀的翘曲变形,其应力分布已远非初等理论所能描述,而正在广泛应用的经典夹层理论却都建立在平面假设基础上,尤其不能正确反映弱芯的轻质夹层结构的行为,本文放弃了不合理的假设,将夹芯梁视为一般层状弹性体,严格按弹性理论导出了既满足控制方程又同时满足全部边界条件、层间的应力及位移的连续条件的封闭解.它可确切地反映夹芯梁的位移形态和应力分布,并从不同角度,包括多种实验和FEM数值解,验证了它的正确性.     

Flexural properties of fiber‐reinforced polypropylene composites with and without a transcrystalline layer

The flexural properties of isotactic polypropylene (PP) matrix composites reinforced with 5–30 vol% of unidirectional pitch‐based carbon, polyacrylonitrile (PAN)‐based carbon, e‐glass or aramid fibers were measured using both static and dynamic test methods. Previous research has shown that these pitch‐based carbon and aramid fibers are capable of densely nucleating PP crystals at the fiber surface, leading to the growth of an oriented interphase termed a “transcrystalline layer” (TCL), while the e‐glass and PAN‐based carbon fibers show no nucleating ability. The PP matrices examined included unmodified homopolymers, nucleated homopolymers and PP grafted with maleic anhydride (MA). The composites based on the unmodified PP homopolymers all exhibited poor fiber/matrix adhesion, regardless of fiber type and presence or absence of a TCL. The addition of nucleating agent to the PP matrix had no measurable effect on either the amount of TCL material in pitch‐based carbon‐fiber‐reinforced composites, as measured by wide‐angle X‐ray scattering, WAXS, or the static flexural properties of the composites reinforced with either type of carbon fiber. However, MA grafting reduced the transcrystalline fraction of the matrix in pitch‐based carbon‐fiber‐reinforced composites; at the highest level of MA grafting, the TCL was completely suppressed. In addition, high levels of MA grafting improved the transverse flexural modulus of the composites containing both types of carbon fibers, and reduced the extent of fiber pull‐out, indicating an improvement in fiber/matrix adhesion. Copyright © 1999 John Wiley & Sons, Ltd.