Surfaces of Constant Mean Curvature Bounded by Two Planar Curves

In this paper we study constant mean curvature compact surfaces with two Jordan curves in parallel planes as boundary and we investigate the point at which the surface inherits the symmetries of its boundary.     

Linearization of column responses by correlation chromatography. Separation improvement and reduction of undesired adsorption effects

Summary Experiments and simulations prove that correlation chromatography can greatly reduce the disadvantage of a non-linear response of the chromatographic column. A factor that has been accepted as being an important source of error in correlation or multiplex chromatography, has been shown not to be. Separations affected, improve dramatically when correlation chromatography is used, and a substantial amount of correlation noise only arises when there is a large difference in separation between a conventional chromatogram and a correlogram.A model has been developed for simulating these nonlinearities. It is shown that, especially for correlation chromatography, the simulation results match the practical measurements very well.     

相量法在实际生产中的应用

本文详细说明了在实际生产中应用相量法能够快速、准确地分析和排除电力系统故障。     

固体力学有限元体系的结构拓扑变化理论

本文是文[1]的继续.文[1]提出了杆件系统的结构拓扑变化理论和拓扑变化法本文将这一理论和方法推进到连续体有限元体系;且在此基础上揭示出有限元体系的一个新性质,称为基本位移之梯度的正交性定理,从而给出一套设计敏度的显式表达式,可直接用于计算.     

Local and Parallel Finite Element Algorithms for Eigenvalue Problems

Abstract Some new local and parallel finite element algorithms are proposed and analyzed in this paper foreigenvalue problems.With these algorithms, the solution of an eigenvalue problem on a fine grid is reduced tothe solution of an eigenvalue problem on a relatively coarse grid together with solutions of some linear algebraicsystems on fine grid by using some local and parallel procedure.A theoretical tool for analyzing these algorithmsis some local error estimate that is also obtained in this paper for finite element approximations of eigenvectorson general shape-regular grids.     

Recursive partition and amalgamation with the exponential family: Theory and applications

The theory of tree-growing (RECPAM approach) is developed for outcome variables which are distributed as the canonical exponential family. The general RECPAM approach (consisting of three steps: recursive partition, pruning and amalgamation), is reviewed. This is seen as constructing a partition with maximal information content about a parameter to be predicted, followed by simplification by the elimination of ‘negligible’ information. The measure of information is defined for an exponential family outcome as a deviance difference, and appropriate modifications of pruning and amalgamation rules are discussed. It is further shown how the proposed approach makes it possible to develop tree-growing for situations usually treated by generalized linear models (GLIM). In particular, Poisson and logistic regression can be tree-structured. Moreover, censored survival data can be treated, as in GLIM, by observing a formal equivalence of the likelihood under random censoring and an appropriate Poisson model. Three examples are given of application to Poisson, binary and censored survival data.     

Stability testing in an integrated scheme

ISO Guide 35 deals with RM stability issues and scrutinizes the evaluation of stability testing results under the assumption that either there is no trend at all (a rather rare situation), or any observed deterministic change is insignificant and thus can be neglected. However, market demands for reliable reference materials are obviously not limited to stable or at least seemingly stable materials. In many analytical applications, analytes and measurands under consideration are known, or at least suspected, to be unstable on time scales that may vary widely from measurand to measurand. The Federal Institute for Materials Research and Testing (BAM) has developed (and successfully uses) an integrated approach in its certification practice. The approach is based on an initial stability study and subsequent post-certification monitoring. Data evaluation is model-based and takes advantage of all information collected in the stability testing scheme(s). It thus allows one to deal with any kind of instability observed, to assess limiting time intervals at any stress condition in the range tested, to estimate a final expiry date for materials with detected instabilities or the maximum admissible re-testing interval for seemingly stable materials, and to assess maximum admissible stress loads during delivery of the material to the customer. The article describes (and exemplifies) typical study layout, the model selection, and the integrated data assessment.     

Mass Power Spectrum in a Universe Dominated by the Chaplygin Gas

The mass power spectrum for a Universe dominated by the Chaplygin gas is evaluated numerically from scales of the order of the Hubble horizon to 100 Mpc. The results are compared with a pure baryonic Universe and a cosmological constant model. In all three cases, the spectrum increases with k, the wavenumber of the perturbations. The slope of the spectrum is higher for the baryonic model and smaller for the cosmological constant model, the Chaplygin gas interpolating these two models. The results are analyzed in terms of the sound velocity of the Chaplygin gas and the moment the Universe begins to accelerate.     

Carathéodory's method for a class of dynamic games

The method of equivalent variational methods, originally due to Carathéodory for free problems in the calculus of variations is extended to investigate feedback Nash equilibria for a class of n-person differential games. Both the finite-horizon and infinite-horizon cases are considered. Examples are given to illustrate the presented results.     

Method of lines with boundary elements for 1‐D transient diffusion‐reaction problems

Time‐dependent differential equations can be solved using the concept of method of lines (MOL) together with the boundary element (BE) representation for the spatial linear part of the equation. The BE method alleviates the need for spatial discretization and casts the problem in an integral format. Hence errors associated with the numerical approximation of the spatial derivatives are totally eliminated. An element level local cubic approximation is used for the variable at each time step to facilitate the time marching and the nonlinear terms are represented in a semi‐implicit manner by a local linearization at each time step. The accuracy of the method has been illustrated on a number of test problems of engineering significance. © 2005 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq 2006