Improved coating method for uniform polymer layer in infrared hollow fiber

An improved coating method was proposed in order to form a uniform polymer layer in the fabrication of cyclic olefin polymer-coated silver (COP/Ag) hollow fiber. A COP solution was flowed in a closed loop, in which the silver-coated tube was used as a part of the loop. Owing to the constant flowing speed of the COP solution and the airtight flowing environment, a COP layer was uniformly formed. The hollow fibers attain high performance and deliver multi-wavelength laser light from the infrared to the visible simultaneously. The method was successfully applied to the fabrication of practical hollow fibers with 2 m length for the near and mid-infrared lasers.     

荧光光纤温度传感器激励光源的选择

本文分析计算了荧光光纤温度传感器的温敏元件——GsAlAs/GaAs双异质结半导体材料的荧光辐射效率与激励光波长的关系。讨论了温度测量范围及温敏元件GaAlAs层铝含量对激励光源的限制,在0～200℃测温范围内,若采用LED作激励光源,其峰值波长应在0.70～0.76μm之间选择。     

Spatiotemporal and Thermal Analysis of VCSEL for Short-range Gigabit Optical Links

High-speed Optoelectronic Modules using Vertical Cavity Surface Emitting Lasers (VCSEL) coupled to Multi Mode Fibers (MMF) are a performing and low-cost solution for 10 Gigabit Ethernet (10 GbE) in short-distance optical links. A complete model of the spatiotemporal behavior of multimode VCSELs, through static and dynamic response, noise, thermal effects, and its coupling to MMF has been investigated. Relative Intensity Noise shows modal dependence and can be affected by spatial filtering due to coupling and fiber propagation. Simulations permit to evaluate critical parameters, such as modulation formats, launching conditions, and operating temperature for global bandwidth and eye diagram optimization up to 10 Gb/s. Simulation results are compared to measurements on prototype optoelectronic modules.     

喷丝头组合花板的真空熔炼

化纤生产行业的粘胶，经过装在组合花板上的喷丝头在酸浴里形成化学纤维。粘胶为碱性物质，酸浴的化学成份为稀硫酸、磷酸，酸浴温度为57℃左右，组合花板内压力为10kg／cm^2，要求组合花板材料在有足够的强度下，具有高耐腐蚀性能。     

800nm激光泵浦掺Nd^3＋的氟化物玻璃光纤正向双程超荧光分析

从实验上探讨了掺Ｎｄ＾３＋的氟化物玻璃光纤正向双程超荧光基本特性，包括输入－输出特性、输出－带宽特性以及输出－波长（激发）特性。并给出了理论上的拟合公式，实验表明利用氟化物玻璃光纤有望获得性能优异的有应用前景的低相干度集成化光源。     

气密性碳涂覆光纤筛选强度与电阻关系研究

通过实验分析确立了把光纤电阻作为衡量气密性碳涂覆光纤通过２％应变筛选的过渡标准。要拉制２％应变筛选的碳涂覆光纤，其电阻值应小于３０ｋΩ／ｃｍ。     

线圈型全光纤偏振器的研究

本文采用等效电流法对线圈型全光纤偏振器进行了分析计算.对应于保偏光纤中两正交传输基模的消光比,提出了一种分析保偏光纤弯曲损耗的新方法,这种方法基于将保偏光纤两个不同偏振模式分别等效为两个普通圆光纤的基模,等效参数通过测量不同偏振模式的模场半径来确定.实验证明这种理论计算方法与实验结果一致.最终,我们研制出的线圈型光纤偏振器在1.31μm工作波长下,实测消光比达30dB以上,工作偏振模式插入损耗≤3dB.     

纤维的形变和断裂——Ⅰ.拉伸角蛋白纤维形变和断裂的动态研究

作者在扫描电子显微镜样品室中拉伸角蛋白纤维,观察纤维形变和断裂的过程并摄取其照片。采用低加速电压观察和适当的样品准备技术,避免了纤维在拉伸过程中出现荷电现象。该现象是非导电材料作动态观察的主要困难。从所观察到的纤维形变和断裂形态和高聚物断裂理论讨论了角蛋白纤维的形变和断裂机理。结论如下:角蛋白纤维伸长和断裂过程中出现银纹样形态,但其断裂为脆性方式;该类纤维的拉伸断裂起始于角质细胞的内、外角质层;角质与角质和角质与皮质细胞间的物质是角蛋白纤维的力学薄弱区。     

毛细管电泳安培检测扑热息痛及其水解物

研究了各种电化学预处理条件下碳纤维电极对扑热息痛及水解物的电化学行为。确定该体系最佳预处理条件为０．２Ｖ电位下阳极化１ｍｉｎ，再于－２．０Ｖ下阴极化１０ｓ。预处理后的碳纤维伏安响应得到明显提高。运用最佳条件并在支持电解中加入添加剂后，扑热息痛及其水解物在毛细管电泳上获得很好的分离和检测。其中扑热息痛的检测下限为２．７８ｐｇ；对氨基酚为１．８４ｐｇ。