关于居住小区若干问题探讨

通过对我国居住小区的模式、规模、结构、布局等现存问题的分析,提出了一些针对性的建议。     

结构可靠性设计中尺寸变差系数的确定方法

提出了在结构可靠性设计中,根据现有加工条件和设计要求确定几何尺寸变差系数的思想,并给出了当已知精度等级时,直接加工尺寸和组合尺寸变差系数的计算方法和程序。采用该方法使可靠性设计更切合实际。     

Pb-Sn-Bi三元系α相固溶体的点阵参数

应用X射线衍射法测定了Pb-Sn-Bi三元系Pb基α相固溶体的点阵参数,发现点阵间距与成分呈线性变化,对两批实验数据分别进行回归分析,得到点阵参数-浓度关系的统一解析式: α=0.49495X_(Pb)+0.47813X_(Sn)+0.50629X_(Bi)。其F检验置信度大于99.9％,残余标准差σ=6.4×10~(-5) nm,分析点阵畸变的影响因素表明尺寸效应是控制固溶体点阵行为的主要因素。     

从小说《围城》看中国文化的面子观

面子及对面子的需求在中西文化中具有不同的文化特征。通过对《围城》文本的分析，可以检验布朗和莱文森·的面子理论在中国文化中的价值与理论解释力，从而阐释中国文化中面子的特殊含义与礼貌表现。     

Particle Size Analysis by Transmission Fluctuation Spectrometry: Experimental Results Obtained with a Gaussian Beam and Analog Signal Processing

Transmission fluctuation spectrometry (TFS) is a method for the analysis of particle size distributions based on the statistical fluctuations of a transmission signal. Complete information on the PSD and particle concentration can be retrieved by a special transformation of the transmission signal, whereby the expectancy of the transmission square (ETS) is determined after the signal has been subjected to a procedure of spatial and temporal averaging. By varying the averaging parameters over a wide range, a spectrum of ETSs is obtained and introduced into a linear equation system, which yields the PSD. In the experimental realization presented here, variable temporal averaging is realized in the frequency domain with a series of low pass filters at different cutoff frequencies while spatial averaging inevitably occurs as the particles pass through a focused Gaussian beam of finite cross section. Experimental results on spherical particles (glass beads) and non‐spherical particles (SiC) are presented. The PSDs are resolved in 30 intervals within a particle size range from 1–1000 μm, employing a modified Chahine inversion algorithm. So far, the measurements are limited to moderate particle concentrations. Some influences affecting the measurements, especially for higher particle concentrations, are discussed in detail.     

采煤工作面瓦斯涌出分析及控制技术

分析了采煤工作面瓦斯涌出规律及其主要影响因素,论述了瓦斯治理及控制技术。     

数字监控系统中有辨认价值的人面像

结合案例,从分辨率的角度对监控系统中人面像的可分辨程度进行了论述,并说明了数字监控系统中提取的人面像在公安工作中的利用价值。     

步进电机细分技术在经济型数控机床中的应用

本文叙述了步进电机细分原理及微机控制系统，并将其应用于经济型数控铣床的横向进给伺服系统，有效提高了开环数控系统的定位精度。     

加工硬质合金端铣刀刀槽时的工艺调整计算

硬质合金端铣刀刀体上的刀槽，通常将设计为槽底与铣刀轴线倾斜δ角，槽侧壁与铣刀轴线倾角为ω且偏移一个距离为ｅ，以使刀齿装夹在刀体上后获得端铣刀所需的几何角度。本文主要论述在万能铣床上铣削铣刀体上具有δ、ω、ｅ的刀槽时必要的工艺调整，利用矢量及座标转换推导了加工刀槽时必要的参数计算公式，为高效率、高质量地进行铣刀体刀槽的加工提供了一种精确可行的参数计算方法。