Cu－Ni－Sn合金在形变加深冷后的组织与性能

一般调幅结构铜合金的σｂ均在１０００ＭＰａ左右，属于中等强度．采用形变加深冷的新工艺，可获得１４００ＭＰａ以上高强度钢合金．还讨论了深冷后的组织和性能．     

CuAlNiMnTi形状记忆合金马氏体时效研究

利用Ｘ射线分析、原位电阻测量等方法研究了ＣｕＡｌＮｉＭｎＴｉ在马氏体不同温度的时效效应。实验结果表明，淬火态ＣｕＡｌＮｉＭｎＴｉ合金在马氏体态时效过程中发生马氏体稳定化现象；在这一过程中ＯＤ３长程度有序无明显变化，但发生了原子短程无序。马氏体稳定化主要是由原子短程无序引起。     

快凝Al－8．5Fe－1．3V－1．7Si合金高温下的相稳定性

采用透射电镜研究了快速凝固Ａｌ－８．５Ｆｅ－１．３Ｖ－１．７Ｓｉ合金在６００℃长时间热暴露后强化相的转化行为．结果发现，高温下稳定性极好的Ａｌ１２（Ｆｅ，Ｖ）３Ｓｉ相在６００℃时粗化速率明显加快．在有些强化相颗粒粗化的同时，伴随部分小尺寸颗粒的溶解．随热暴露时间的延长，强化相体积分数减小，粗化的颗粒外形由球形变为多边形，半共格关系遭到破坏．热暴露２００ｈ后，在基体中有异常粗大的Ａｌ１３（Ｆｅ，Ｖ）形成，该相为底，Ｘ单斜结构，相内为孪晶结构．     

Mg-(6～8)A1-0.7Si合金的组织和力学性能分析

通过金相观察、扫描电镜、X衍射分析和拉伸实验等方法,研究了Mg-(6~8)A1-0.7Si合金的铸态组织和力学性能.研究结果表明:添加了少量Sb和RE的Mg-(6~8)%A1-0.7%Si的铸态组织主要由α-Mg基体、Mg17A l12相、Mg2Si相、Mg3Sb2相和少量针状A l4Si2Mn2Y相组成,并且随着A l含量的增加,试验合金组织中的Mg17A l12相增多,共晶析出物变得更加连续.同时,力学性能的测试结果表明:A l含量变化对于试验合金抗拉强度、屈服强度和延伸率的影响呈现出不同的变化规律.     

中碳铬钨渗氮轴承钢旋转弯曲疲劳性能研究

针对轴承钢失效形式主要为疲劳破坏的问题,对中碳铬钨渗氮轴承钢进行旋转弯曲疲劳（RBF）试验及分析。分析轴承钢经调质处理（880 ℃+540 ℃）后的组织,再经RBF试验后疲劳断口和渗氮处理的作用,还分析了非金属夹杂物对轴承钢RBF的影响,构建了非金属夹杂物深度和尺寸对中碳铬钨渗氮轴承钢RBF极限强度影响的模型。实验结果表明：试验钢调质处理后,组织为回火索氏体,主要析出M₆C型和M₂₃C₆型碳化物,力学性能优良,RBF极限强度达到729 MPa;疲劳源分为表面缺陷和内部非金属夹杂物,表面缺陷主要包括非金属夹杂物脱落形成的凹坑以及机加工留下的刀痕,非金属夹杂物主要为镁铝酸盐;轴承钢在NH₃渗氮气氛中560 ℃恒温保持25 h,渗氮层厚度达360 μm以上,渗氮工艺合适。研究结果对中碳铬钨渗氮轴承钢的发展及其疲劳性能的提高有一定的参考价值。     

Surface modification of Ti-45Al-8.5 Nb alloys by microarc oxidation to improve high-temperature oxidation resistance

Microarc oxidation(MAO)electrolysis plasma deposition was used to prepare Al_2O_3coatings on Ti-45Al-8.5 Nb alloys to improve high temperature oxidation resistance.The surface and cross-section morphologies before and after high-temperature oxidation,the chemical composition,and the phase identification of the coatings were investigated by scanning electron microscopy(SEM),electron probe microanalyses(EPMA),and X-ray diffraction(XRD).The results show that Al_2O_3coatings with a thickness of approximately 8μm can be obtained on the Ti-45Al-8.5 Nb alloys by MAO for 600 s.The samples with the Al_2O_3coatings exhibited better high-temperature oxidation resistance.A minimal weight gain of only 0.396 g/m~2after 100 h oxidation at 900°C was observed for the coatings formed with a deposition voltage of 400 V and using a duty cycle of 3%.The deposition mechanism of the Al_2O_3coatings and the effect of the MAO parameters are also described.     

Effect of minor Sc on the microstructure and mechanical properties of AZ91 Magnesium Alloy

The as-cast and heat-treated microstructures and mechanical properties of the AZ91 magnesium alloys with and without minor Sc addition were investigated and compared in this paper. The results indicated that adding0.15–0.45 wt% Sc to the as-cast AZ91 alloy not only could modify and refine the Mg_(17)Al_(12) phase but also suppress the formation of the Mg_(17)Al_(12) phase. At the same time, the grains of the Sc-containing as-cast AZ91 alloys were also effectively refined. As a result, the mechanical properties at room temperature(RT) for the Sccontaining as-cast AZ91 alloys were effectively improved. In addition, adding 0.15–0.45 wt%Sc to the AZ91 alloy promoted the formation of the continuous precipitates(CP) during the aging treatment in spite of that the formation of the discontinuous precipitates(DP) was simultaneously suppressed. Accordingly, the Sc-containing as-aged AZ91 alloys obtained the relatively higher mechanical properties at RT than the as-aged AZ91 alloy.     

The hidden disintegration of cluster heterogeneity in Fe-based glass-forming alloy melt

The evolution of liquid metal at high temperature is known much less than their solid states. This is partially due to that the message concerning clusters, metastable phase or heterogeneity in liquid is usually too slight to be traced. Here, we shed some light on the nature of structural evolution of Fe-based glass-forming alloy during overheating process by the investigation of high-temperature melt viscometry and first principles simulations. It was found that a structural transition around 1400 ℃ occurred in the melts of initial homogeneous ingot, heterogeneous ingot and amorphous ribbons jointly, and was confirmed by the results from differential scanning calorimeter(DSC), and ab initio molecular dynamics(AIMD). Combining these results with Fe-Si-B ternary phase diagram and the melting characteristics of Fe-B compounds, it is safe to conclude that the disintegration of Fe_2B type clusters to Fe_3B-type clusters leads to the observed transition. These results offer a significant reference for the preparation and property control of Fe-based amorphous alloys.     

离子液体辅助合成AuPd纳米海绵及催化性能

在功能化离子液体氯化1-羟乙基-3-甲基咪唑([HEmim]Cl)辅助下,在室温水溶液中一步快速合成了具有多孔海绵状结构的AuPd纳米材料.通过场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、X射线能谱(EDX)和X射线衍射分析(XRD)等对该材料进行了表征.结果表明,AuPd纳米海绵为合金结构,由表面粗糙的纳米颗粒聚集熔接而成.采用不同摩尔比(3∶1,1∶1或1∶3)的前驱物HAuCl₄和Na₂PdCl₄均可制备出海绵状AuPd合金结构.离子液体对AuPd纳米海绵状结构的形成起关键作用.在对硝基苯酚还原反应中,不同组成的AuPd纳米海绵均表现出比商用Pd/C催化剂更优异的性能.其中,Au₁Pd₃纳米海绵具有最高的催化活性,反应在98 s内即可完成,反应速率常数为0. 0143 s^-1,是商用Pd/C的2. 3倍.该方法也可用于制备其它双金属(如PdCu,PtCu等)和多金属纳米海绵.     

磁致冷材料钆硅锗系合金中Si和Gd的重量法联测的研究

参考了HClO4脱水重量法测定Si及草酸盐重量法测定Gd的方法,建立了钆硅锗系合金中主成分Si和Gd联合测定的方法,并详细考查了共存元素及杂质元素对测定的影响。合金共存元素Ge在HCl的存在下,绝大部分可以GeCl4的形式被蒸发,达到与被测元素分离的目的。熔样过程引入的杂质元素Ni可与被测元素Gd,用氨水沉淀分离,残留Ni不足以影响Gd的测定。方法回收率在98.5%以上,Si和Gd的测量相对标准偏差分别在2.6%~3.0%和0.4%~0.5%。