应变速率对8090Al-Li合金拉伸性能的影响

用动态拉伸的方法研究了应变速率对 80 90 Al— L i合金拉伸性能的影响 ,应变速率的范围为 10 - 3～ 10 3s- 1。结果表明 ,合金的强度和塑性随应变率的增加而增加。试样的 SEM和 TEM分析发现 :准静态下的断裂为沿晶断裂 ;随着应变率的增加 ,断裂从穿晶准解理断裂过渡到由显微空穴聚集而成的韧窝断裂。高应变率下80 90 Al- L i合金强度和塑性的提高与其变形机制和晶界无沉淀区 (PFZ)的变化有关     

Magnetic susceptibility of liquid gold-indium-zinc alloys

Summary Alloys of the ternary system gold-indium-zinc with a variable content of goldx _Au at a constant ratio ofx _In:x _Zn=1:1 have been investigated by susceptibility measurements from 300 K up to 1500 K with emphasis on the liquid state. The magnetic susceptibilities of the homogeneous liquids were found to vary in a non-linear manner with temperature and composition. At temperatures close to the liquid-solid transition, the susceptibilities pass through a characteristic minimum which tends to disappear with increasing temperature. The anomaly located atx _Au 0.6 seems to be related to a particular valence electron concentration ofe/a 1.6.

---

Magnetische Suszeptibilität von flüssigen Gold-Indium-Zink-Legierungen

Zusammenfassung Legierungen des ternären Systems Gold-Indium-Zink mit einem variablen Goldgehaltx _Au bei konstantem Indium-Zink-Verhältnis (x _In:x _Zn=1:1) wurden zwischen 300 und 1500 K auf ihre magnetische Suszeptibilität untersucht. Das Hauptaugenmerk wurde dabei auf den flüssigen Zustand gelegt. Die magnetischen Suszeptibilitäten der homogenen Schmelzen variieren nichtlinear mit Temperatur und Zusammensetzung. Bei Temperaturen nahe dem übergang flüssig-fest tritt ein charakteristisches Minimum der Suszeptibilität auf, das mit steigender Temperatur verschwindet. Die Anomalie bei einemx _Au vonca. 0.6 scheint mit einer speziellen Valenzelektronenkonzentration (e/a) von etwa 1.6 verknüpft zu sein.

     

温度对贮氢合金MlNi3.75Co0.65Mn0.4Al0.2动力学性能的影响

在-20℃～85℃的范围内系统地研究了温度对贮氢合金MINi3.75Co0.65Mn0.4Al0.2动力学性能的影响.结果表明:该贮氢合金电极的电化学反应电阻Rt,欧姆内阻Ro,阴极极化过电位,阳极极化过电位,阳极极化过程中的电化学反应过电位ηa和浓差极化过电位ηa均随温度的升高而减小,该电极的交换电流密度i0,对称因子β和电极中氢的扩散系数D随温度的升高而增大.当放电电流密度较低时,电化学反应是整个电极过程的速度控制步骤;当放电电流密度较高时,氢的扩散是整个电极过程的速度控制步骤;在中等放电电流密度下,电极过程由电化学过程和氢的扩散过程混合控制.该电极中电化学反应过程和氢扩散过程的活化能分别为28.1 kJ·mol-1和19.9 kJ·mol-1.     

往复挤压准晶增强快速凝固Mg92.5Zn6.4Y1.1合金

采用往复挤压工艺将快速凝固Mg92.5Zn6.4Y1.1合金薄带在330℃挤压2道次和4道次,然后正挤压制成Φ10 mm的棒材。用OM,TEM,XRD及DTA研究了往复挤压过程中准晶相I-Mg3YZn6弥散析出及对力学性能的影响。研究表明,往复挤压有利于快速凝固Mg92.5Zn6.4Y1.1合金薄带的焊合,获得组织致密、均匀、高强韧合金。往复挤压2道次,相组成为-αMg和准晶I-Mg3YZn6,脱溶析出纳米准晶相较少;4道次相组成为-αMg和准晶I-Mg3YZn6及MgZn相,脱溶弥散析出的纳米I-Mg3YZn6准晶相及MgZn相较多。往复挤压提高材料的拉伸性能,其主要原因是细晶强化和析出强化。     

低钴AB5型稀土系贮氢电极合金的研究

为了进一步降低AB5型混合稀土系贮氢合金的成本,采用Cr,Si,Cu替代Co和调节化学计量比的方法制备低钴AB5型贮氢合金。结果表明:3种取代元素在寿命方面的效果依次为Si>Cr>Cu,在放电容量和活化性能方面依次是Cu>Cr>Si。Cr,Cu,Si只有少量的替代才可能发挥其有利影响;通过非化学计量比的调节,低钴混合稀土系贮氢电极合金的放电容量、活化性能及倍率放电能力都能较好地达到实用要求,但是循环寿命有待提高。     

铜(Ⅱ)-铬天青S-过氧化氢体系催化光度法测定痕量铜

本文研究了在氨水介质中,痕量铜对过氧化氢氧化铬天青S褪色反应的催化作用,建立了一个催化光度法测定痕量铜的新方法。线性范围为0～20ng/mL,检出限为5.59×10~(-11)g/mL,并用于铝合金标准样品,环境标准样品和自来水中痕量铜的测定。     

Differential scanning calorimetry and the advanced solidification processing of metals and alloys

This paper describes some examples of the use of differential scanning calorimetry (DSC) in providing information for advanced solidification processing of metals and alloys. Spray forming, squeeze casting, grain refinement and crystallization of amorphous alloys are all discussed. DSC measurements are shown to be valuable for testing kinetic theories of nucleation and growth, and validating solidification process models.     

Corrosion-stable nickel- and cobalt-based alloys for dental applications

In a comparative study the in vitro corrosion behavior of a selection of nickel- and cobalt-based alloys for application in dentistry containing no noble metals was studied with slow scan cyclic voltammetry. The obtained breakthrough potentials, the repassivation behavior and further typical features of the cyclic voltamograms are correlated with the chemical composition as measured with electron beam microanalysis. Surface inhomogenities detected with the latter method are discussed with respect to the electrochemical behavior. For all alloys stabilities in terms of breakthrough potential superior to previously reported data for nickel-base alloys are found.     

Thermodynamics of liquid Fe-Si and Fe-Ge alloys

The enthalpies of mixing of liquid binary Fe-Ge (1765±5 K) and Fe-Si (1750±5 K) alloys were determined using a high-temperature isoperibolic calorimeter. The thermodynamic properties of Fe-Ge melts were also studied by electromotive force method in the temperature range of 1250-1580 K. The comparison of our measurement results with literature data has been performed. The extreme negative values of integral enthalpy of mixing and alternating-sign deviations from Raoult's low for germanium can be explained by the influence of binary clusters formation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Cathodic deposition of ternary In+As+Sb alloys and formation of InAsxSb1−x

In+As+Sb alloys have been deposited onto Ni and Ti cathodes from tartaric acid solutions at pH 2. Homogeneous deposits of composition suitable for achieving InAs_xSb_1−x can be obtained from this medium. The As-to-Sb ratio can be controlled by properly selecting solution composition and deposition potential.X-ray photoelectron spectroscopy and X-ray diffraction analyses show that formation of III–V compounds occurs at room temperature. In reacts preferentially with As rather than with Sb, but crystalline phases formed at room temperature are Sb-rich. After annealing the In+As+Sb alloys at 250°C, the composition calculated from cell parameters appears similar to that measured by energy-dispersive X-ray analysis, suggesting that the entire deposit has been converted into the InAs_xSb_1−x crystalline phase.