CuAlNiMnTi形状记忆合金马氏体时效研究

利用Ｘ射线分析、原位电阻测量等方法研究了ＣｕＡｌＮｉＭｎＴｉ在马氏体不同温度的时效效应。实验结果表明，淬火态ＣｕＡｌＮｉＭｎＴｉ合金在马氏体态时效过程中发生马氏体稳定化现象；在这一过程中ＯＤ３长程度有序无明显变化，但发生了原子短程无序。马氏体稳定化主要是由原子短程无序引起。     

快凝Al－8．5Fe－1．3V－1．7Si合金高温下的相稳定性

采用透射电镜研究了快速凝固Ａｌ－８．５Ｆｅ－１．３Ｖ－１．７Ｓｉ合金在６００℃长时间热暴露后强化相的转化行为．结果发现，高温下稳定性极好的Ａｌ１２（Ｆｅ，Ｖ）３Ｓｉ相在６００℃时粗化速率明显加快．在有些强化相颗粒粗化的同时，伴随部分小尺寸颗粒的溶解．随热暴露时间的延长，强化相体积分数减小，粗化的颗粒外形由球形变为多边形，半共格关系遭到破坏．热暴露２００ｈ后，在基体中有异常粗大的Ａｌ１３（Ｆｅ，Ｖ）形成，该相为底，Ｘ单斜结构，相内为孪晶结构．     

Mg-(6～8)A1-0.7Si合金的组织和力学性能分析

通过金相观察、扫描电镜、X衍射分析和拉伸实验等方法,研究了Mg-(6~8)A1-0.7Si合金的铸态组织和力学性能.研究结果表明:添加了少量Sb和RE的Mg-(6~8)%A1-0.7%Si的铸态组织主要由α-Mg基体、Mg17A l12相、Mg2Si相、Mg3Sb2相和少量针状A l4Si2Mn2Y相组成,并且随着A l含量的增加,试验合金组织中的Mg17A l12相增多,共晶析出物变得更加连续.同时,力学性能的测试结果表明:A l含量变化对于试验合金抗拉强度、屈服强度和延伸率的影响呈现出不同的变化规律.     

Surface modification of Ti-45Al-8.5 Nb alloys by microarc oxidation to improve high-temperature oxidation resistance

Microarc oxidation(MAO)electrolysis plasma deposition was used to prepare Al_2O_3coatings on Ti-45Al-8.5 Nb alloys to improve high temperature oxidation resistance.The surface and cross-section morphologies before and after high-temperature oxidation,the chemical composition,and the phase identification of the coatings were investigated by scanning electron microscopy(SEM),electron probe microanalyses(EPMA),and X-ray diffraction(XRD).The results show that Al_2O_3coatings with a thickness of approximately 8μm can be obtained on the Ti-45Al-8.5 Nb alloys by MAO for 600 s.The samples with the Al_2O_3coatings exhibited better high-temperature oxidation resistance.A minimal weight gain of only 0.396 g/m~2after 100 h oxidation at 900°C was observed for the coatings formed with a deposition voltage of 400 V and using a duty cycle of 3%.The deposition mechanism of the Al_2O_3coatings and the effect of the MAO parameters are also described.     

The hidden disintegration of cluster heterogeneity in Fe-based glass-forming alloy melt

The evolution of liquid metal at high temperature is known much less than their solid states. This is partially due to that the message concerning clusters, metastable phase or heterogeneity in liquid is usually too slight to be traced. Here, we shed some light on the nature of structural evolution of Fe-based glass-forming alloy during overheating process by the investigation of high-temperature melt viscometry and first principles simulations. It was found that a structural transition around 1400 ℃ occurred in the melts of initial homogeneous ingot, heterogeneous ingot and amorphous ribbons jointly, and was confirmed by the results from differential scanning calorimeter(DSC), and ab initio molecular dynamics(AIMD). Combining these results with Fe-Si-B ternary phase diagram and the melting characteristics of Fe-B compounds, it is safe to conclude that the disintegration of Fe_2B type clusters to Fe_3B-type clusters leads to the observed transition. These results offer a significant reference for the preparation and property control of Fe-based amorphous alloys.     

Cu-Zn-Al合金热弹性马氏体稳定化及单向记忆寿命估计

本文研究了Cu-Zn-Al合金热弹性马氏体稳定化问题。实验表明,不论直接淬火或分级淬火的合金,当其在马氏体状态时效时,都会发生热弹性马氏体稳定化现象,但后者稳定化速率大为减小,其激活能远大于前者。这一结果可用来估计单向记忆寿命。此外,本文还从结构上研究了马氏体稳定化机理,认为再有序化和空位钉扎是影响马氏体稳定化的诸多因素中的两个重要因素。     

铜合金时效性能的神经网络预测模型

运用BP神经网络算法，对时效试验数据进行训练，建立了Cu-0．30Cr-0．15Zr合金时效后硬度和导电性与时效时间和时效温度的映射模型，从而可预测铜合金在一定时效条件下的硬度和导电性，预测结果与实测值吻合较好，表明神经网络用于铜合金的时效性能预测是可行的，预测的准确性取决于用于训练网络的铜合金时效试验数据的数量和质量。     

加工条件对聚丙烯釜内合金结构及性能影响

运用动态力学分析(DMA)、差示扫描量热法(DSC)、流变分析等手段研究了加工条件对聚丙烯釜内合金结构的影响,并结合力学性能表征建立了结构与性能的关系.研究结果表明,在设定的加工条件下,聚丙烯釜内合金的熔融结晶特性和流变性能基本上没有变化.聚丙烯和乙丙橡胶组份间的相容性却随密炼加工温度的增加得到了明显的改善,来源于剪切诱导组份间的相互扩散.高温密炼加工的聚丙烯釜内合金拉伸断裂伸长率表现出了显著的提高.     

BCO光度法测定含镍铝合金中的铜

针对ＢＣＯ光度法测定含镍铝合金中铜稳定性差的缺点,用ＮＨ３－ＮＨ４Ｃｌ溶液作为缓冲介质对ＢＣＯ法作了改进,测定含镍铝合金中的铜含量,结果稳定、准确,再现性良好,方法简便而实用,特别适用于炉前分析．     

软磁材料应用研究进展

软磁材料因其饱和磁感应强度高、磁导率高、矫顽力低、损耗低和环境稳定性好等优点,被广泛应用于通信、电源、计算机和各种电子产品等领域。随着信息技术和电子产品数字化的发展,电子仪器设备向着精密化、高效化和节能化方向发展,这就对软磁材料和元件提出了新的要求和挑战。如何取得具有较高饱和磁感应强度和低损耗的软磁材料已成为研究的重点。本文对传统软磁材料与新型软磁材料的研究现状作了总结,并对软磁材料的发展趋势作了展望,为后续软磁材料的发展提供指导方向。