Peculiarities of changes of some physicomechanical characteristics of monoisotopes B, B and natural β-boron

Real structure and some physicomechanical characteristics of the samples of natural beta-rhombohedral boron B as well as of its ¹⁰B and ¹¹B monoisotopes have been studied. It was shown that the influence of ¹⁰B and ¹¹B isotopes on physicomechanical properties of boron had a different character. In particular, the samples enriched with ¹¹B had high values of microhardness, shear modulus (SM) and elastic limit if compared to those of boron, while the samples enriched with ¹⁰B monoisotopes were characterized with high values of thermal expansion coefficient (TEC) and thermal conductivity; lattice parameters a and c increased by the sequence: ¹¹B, B, ¹⁰B. It was established that TEC, thermal conductivity, microhardness, SM and shear elastic limit increased in all samples at annealing for 5 h at 1500 °C regardless of isotope content.     

Elastic Moduli and Activation Energies for an Epoxy/m-XDA System by DMA and DSC

The influence of the resin/diamine ratio on the properties of the system diglycidyl ether of bisphenol A (BADGE n=0/m-xylylenediamine) (m-XDA) was studied. Variation of this ratio resulted in significant effects on the cure kinetics and final dynamic mechanical properties of the product material. The study was made in terms of storage modulus (E′), vss modulus (E″) and molecular mass between cross-links (M_c) at different ratios. Two geometries (cylindrical and rectangular) were considered. The influence of temperature was studied through the activation energy (E_a>), which depends on the epoxy/amine ratio and the geometry of the samples. Glass transition temperatures (T_g>) and glass transition temperatures for thermosets with null degree of conversion (T_go>) were determined by DSC. T_g> decreases when amounts of curing agent greatly in excess of the stoichiometric composition were used. This revised version was published online in July 2006 with corrections to the Cover Date.     

弛豫理论对离子交换毛细管电色谱中峰压缩现象的研究

 在毛细管电色谱中,由于溶质在输运过程中所具有的电性质,常会产生一些特殊的现象。这些现象,如离子交换毛细管电色谱中产生超高柱效峰的现象,已经不能用一般的色谱理论加以解释。基于弛豫理论所建立的基本模型,在考虑溶质在两相中皆有可能发生正、反向迁移的情况下,得到了流出曲线一阶原点矩和二阶中心矩的理论表达式,并通过对溶质在两相中电扩散速率与电泳速率、电渗流速率关系的分析结果证实:溶质在固定相表面的电扩散行为可以使其保留变弱,出峰加快;而这种电扩散导致的超常柱效峰的出现具有不稳定性,只有在多方面因素综合影响匹配的情况下才可能出现。     

Atom-surface elastic scattering in the presence of laser radiation

A qualitative discussion on atom-surface elastic scattering taking place in the presence of laser radiation is given. It is suggested that appreciable effects of laser radiation on diffraction patterns may be expected if the laser radiation is capable of inducing electronic transitions in atoms with a large probability.Research sponsored by the Air Force Office of Scientific Research (AFSC), United States Air Force, under Contract No. F49620-78-C-0005, and the National Science Foundation under Grant No. CHE77-27826. The United States Government is authorized to reproduce and distribute reprints for governmental purposes notwithstanding any copyright notation hereon.Alfred P. Sloan Research Fellow, 1976–1980; Camille and Henry Dreyfus Teacher-Scholar, 1975–1980.     

Elastic moduli and structure of low density polyethylene

Summary Low density polyethylene film is drawn at room temperature four times the original length and subjected to thermal annealing at 60, 80, and 100 °C keeping the film length constant. Long spacing measured by SAXS increased with increasing temperature of annealing; the increase of the long spacing is presumed to be due to the decrease of the number of micelles through relaxation during the annealing. Simultaneous measurement of the changes of the long spacing and the film length by stretching is carried out and stress-extension curves are obtained. The values of the initial moduli of the long spacingE ₁ and the film lengthY are very near to each other. Elastic modulus of the crystal latticeE _c is known to be 235 GN/m² and that of the amorphous regionE _a is found to be 0.15 GN/m². When higher stress is applied than in the case of the initial modulus, the percentage of extension of film is much greater than that of the long spacing. The discrepancy is explained by the increase of the number of micelles through stress crystallization.Dedicated to Professor Dr. K. Ueberreiter on the occasion of his 70th birthday.     

Structural Efficiency and Microstructural Modeling of Wet Gels and Aerogels

We present a microstructural model of aerogels that includes the effect of particle necks, tortuosity and dangling ends on the scaling of elastic moduli with density. Relative neck radii can be determined for sintering series of silica aerogels and for Resorcinol Formaldehyde (RF) aerogels produced with different catalyst concentrations. The density of elastically ineffective dangling ends and the tortuosity can be estimated using information from thermal conductivity and elastic modulus measurements in silica aerogels. Typical values for the load bearing mass range from >50% for high density and heat treated aerogels to <10% of the total mass for low density wet-gels.     

Aging effect on the mechanical properties of hybrid gels

Sol-gel derived unsupported films and thin rods have been obtained from co-hydrolysis of triethoxysilane and methyldiethoxysilane. The materials are flexible, dense and transparent. Films and rods have been aged for different periods of time in air at room temperature. The elastic modulus has been measured by means of tensile or flexural tests. Measurements showed an increase of elastic modulus with aging time and showed different values for films and rods. The observed evolution of mechanical properties has been related to a corresponding structural modification as highlighted mainly by MAS-NMR studies. Analyses pointed out the crucial role of condensation processes and showed that the stiffness increase arises from the formation of relatively few bonds which link and constrain pre-existing mobile network regions.     

Inverse relaxation-model and relation to recovery internal friction

Inverse relaxation is studied for hard elastic polypropylene (HEPP), rubber and non-elastic polypropylene. The results show that contractive stress, stress, and internal friction are three essential factors related to the phenomenon. A three-element model in which each element has a definite meaning is proposed to describe this phenomenon. The results also show that, in the first cyclic deformation, relaxation time increases with the increase of recovery for all the materials, which indicates that recovery viscosity increases with the increase of recovery, but the stress rising amplitude (SRA) of inverse relaxation has a maximum in the recovery range. Analysis indicates that SRA equals recovery internal friction (RIF) for ideal material in which stress is solely a function of strain, independent of paths, and approximately equals RIF for non-ideal material at a given strain. From this principle it is found that the order of the work counteracted by RIF for the four materials is the same as that of their second hysteresis loop, and the RIF of HEPP has a sudden increase at the later recovery range.     

General analysis of the measurements of the lateral crystal lattice moduli of semicrystalline polymers by x-ray diffraction and the application to nylon 6

A mathematical representation based on a linear elastic theory is proposed by which one may investigate the dependences of molecular orientation and crystallinity on the crystal lattice moduli and linear thermal expansion coefficients in the direction perpendicular to the chain axis as commonly measured by x-ray diffraction. In the theoretical calculation, a previously introduced model was employed in which oriented crystalline phase is surrounded by oriented amorphous phase and the strains of the two phases at the boundary are identical. The mathematical analysis indicated that the lateral crystal lattice moduli and linear thermal coefficients as measured by x-ray diffraction may be different from the intrinsic crystal moduli and linear thermal coefficients of a crystal unit cell, depending on the structure of the polymer solid. The numerical calculation was applied to nylon 6. As a result, it may be confirmed that the lateral crystal lattice moduli measured by x-ray diffraction are sensitive to the morphology of the bulk speciments and close to the intrinsic crystal moduli if the morphology of the test specimen can be represented by a parallel model with respect to the original stretching longitudinal direction.     

Lattice dynamical study of body-centred tetragonal indium

The phonon dispersion curves, phonon frequency distribution function as well as the lattice specific heat of body-centred tetragonal indium have been deduced using a lattice dynamical model which includes central, angular and volume forces. Six elastic constants, four zone boundary frequencies and an equilibrium condition were used in the evaluation of the force constants. It is shown that this model is elastically consistent and satisfies the symmetry requirements of the lattice, the phonon frequencies of indium deduced from it are in very good agreement with the experimental values of Reichardt and Smith and the theoretical values of Garrett and Swihart, and theθ _D values compare well with the experimental values over a wide temperature range. The apparent discrepancies in the phonon dispersion curves and theθ _D-T curves obtained from deficient models, importance of umklapp processes and the significance of angular forces in the lattice dynamical models are discussed.