FFC-1离子交换纤维物理化学性能的研究

利用扫描电镜、热失重-红外、元素分析、低温氮吸附等技术和化学手段对聚羧酸基FFC-1离子交换纤维的结构与性能特点等进行了系统研究．结果表明：FFC-1离子交换纤维为含适量酰肼类交联键的聚羧酸(钠)型离子交换材料，外比表面积大和传质距离短是其反应动力学性能优异的主要原因，FFC-1纤维具有良好的化学与热稳定性。在5mol/L硫酸、硝酸、盐酸和2mol／L氢氧化钠溶液中浸泡，交换容量未见明显降低。但过氧化氢溶液对其功能基有明显破坏，CO2为FFC-1纤维在高温区间(300℃～350℃)的主要分解产物。     

甲烷二氧化碳介质阻挡放电转化产物分布研究

针对介质阻挡放电甲烷二氧化碳转化实验,分析了反应的产物分布,探讨了进料组成和反应器结构对反应的影响.反应产物包括:高H2/CO摩尔比的合成气、气态烃、高辛烷值的汽油组分、醇和酸等含氧有机物.对所述电极结构,产物的选择性随碳数增加而降低;高的甲烷进料浓度有利于烃的生成,对醇和酸的最佳甲烷进料体积分数范围在67.4％～75.1％;放电间隙越小,原料转化率和烃、酸的选择性越大,大的放电间隙对醇的生成有利.     

Temperature-dependent dry etching characteristics of III–V semiconductors in HBr- and HI-based discharges

Microwave discharges of HBr/H₂/Ar and H/H₂/Ar with additional do biasing of the sample were used to etch InP, GaAs, and AlGaAs at temperatures between 50–250°C. The etch rates increase by factors of 3–50 and 5–9, respectively, for HBr-and HI-based discharges over this temperature range, but display non-Arrhenius behavior. The etched surfaces became very rough above 100°C for InP with either discharge chemistry due to preferential loss of P, while GaAs and AlGaAs are more tolerant of the elevated temperature etching. The near-surface electrical properties of InP are severely degraded by etch temperatures above 100°C, while extensive hydrogen in-diffusion occurs in GaAs and AlGaAs under these conditions, leading to dopant passivation which can be reversed by annealing at 400°C.     

Ga^3＋的新萃取体系的界面特性和胶团化作用研究

研究了Ｇａ~（３＋）协萃体系（Ｇａ~（３＋）－Ｄ_２ＥＨＰＡ－Ｈ_２ＭＰＡ－正十二烷－Ｈ_２ＳＯ_４）的界面吸附和胶团形成热力学，发现该萃取体系中［Ｈ_２ＭＰＡ］影响Ｄ_２ＥＨＰＡ和Ｈ_２ＭＰＡ的界面吸附性质。在中、高［Ｈ_２ＭＰＡ］范围内Ｄ_２ＥＨＰＡ与Ｈ_２ＭＰＡ的界面吸附行为相反，Ｄ_２ＥＨＰＡ的存在也影响Ｈ_２ＭＰＡ的界面吸附行为。研究了界面张力与各因素关系的数学模型，并获得某些胶团形成和界面吸附特性的物化参数。     

Structure and Electrochemical Behavior of Lithium-Manganese Spinels Doped with Chromium and Nickel

A series of compounds with the general formula LiMn_{2 - x - y} Cr _x Ni _y O₄, where x + y = 0.05, 0.5, or 1.0, is synthesized. It is shown that all these compounds are pure-phase spinels with parameter aequal to 0.8193-0.8236 nm. Doping a stoichiometric lithium-manganese spinel simultaneously with chromium and nickel makes the spinel structure stable. The initial specific capacity of a spinel depends on its doping degree. Doping LiMn₂O₄ with chromium and nickel simultaneously at an Mn : Cr : Ni ratio of 195 : 3 : 2 raises the spinel's specific capacity and reduces the cycling degradation. The change in the discharge capacity of LiMn_1.95Cr_0.03Ni_0.02O₄ electrodes cycled at 20, 0, and -14°C is determined.     

Influence of SMA content on the electro-optical properties of polymer-dispersed liquid crystal prepared by monodisperse poly(MMA-co-SMA)/LC microcapsules

Monodisperse poly(methyl methacrylate) (PMMA) particles containing various concentrations of stearyl methacrylate (SMA) were prepared, and a liquid crystal (LC) was swollen into the particles using a solute co-diffusion method (SCM). Phase separation behaviors between the polymer and LC were monitored by utilizing an optical and a polarized microscope (OM/POM). The monodisperse LC microcapsules were then applied to a polymer-dispersed liquid crystal (PDLC), and the electro-optical properties were investigated. As a result, the threshold and driving voltages were improved when the SMA content increased. The long alkyl chains of SMA in the capsules should exist at the interface of the LC and polymer resulting in an enhancement of phase separation between the polymer and LC, which largely influences the electro-optical properties of PDLC.     

Preparation and characterization of functional group gradient surfaces

Functional group gradient surfaces where the density of functional groups changes gradually along the sample length were prepared. The functional group (? COOH, ? CONH₂, and ? OH group) gradient surfaces were produced by the treatment of low-density PE sheets using a corona with gradually increasing power, followed by the graft copolymerization of acrylic acid and subsequent substitution reaction of carboxylic acid groups to amide or hydroxyl groups. The prepared gradient surfaces were characterized by the measurement of water contact angle, FTIR-ATR, and ESCA. The gradient surfaces prepared can be used to systematically investigate the interactions of biological or other species in terms of the surface functional groups and their density of polymeric materials. © 1994 John Wiley & Sons, Inc.     

Reactions in a Mixture of CH4 and CO2 under the Aciton of Microwave Discharge at Atmospheric Pressure

Reactions between CH4 and CO2 under the action of continuous microwave discharge at atmospheric pressure were studied in a special homemade reactor,The main products were CO and H2,while acetylene and ethylene were also found in the products.Experimental results show that conversions of CH4 and CO2 could be higher than 90% without the presence of any catalyst,Effects of CO2/CH4 molar ratio and total flow rate of the feed gas on the reaction were also investigated.     

Effects of type and number of impellers and liquid viscosity on the power characteristics of mechanically agitated gas—liquid systems

Effect of the type and number of high-speed impellers installed on a common shaft on the power characteristics was investigated in water and glucose solutions of different concentration. Different configurations of the Rushton or Smith turbines, pitched blade turbines, propeller, and A 315 impeller were tested. Measurements of power consumption were carried out within the transitional and turbulent regime of the fluid flow using the strain gauge method. Baffled agitated vessels with inner diameter of 0.288 m and 0.634 m were used for the experiments. Liquid height in the vessels was equal to the vessel diameter or it was twice higher. The relative power consumption was compared for different configurations of the impellers. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

Flammability studies of 3-methyl pyridine/water system

In industrial processes, information on the safety property of chemicals is essentially crucial for safe handling during unit operations. Ensuring the safe use of combustible or flammable substances in processes is unlikely without detailed investigations of their flammability characteristics and related hazards. We studied 3-methyl pyridine (3-picoline), e.g., flammability limits (LFL/UFL), maximum explosion pressure (P _max), maximum explosion pressure rise (dP/dt)_max, minimum oxygen concentration (MOC), vapor deflagration index (K _g), and characterized the influence of inert steam (H₂O) on critical parameters for 3-picoline/water mixtures at 270°C, 1 atm, various oxygen concentrations, and vapor mixing ratios (100/0, 30/70, 10/90 and 5/95 vol.%) with a 20-L-Apparatus in simulated conditions, respectively. The results showed that the flammability characteristics of 3-picoline_(aq) all increased with the oxygen concentration. However, as the composition of inert steam increased, the flammability parameters and the degree of fire and explosion hazards were significantly reduced, instead. This study elucidated the flammability properties of 3-picoline mixed with inert steam. The conclusions could be applied to proactively prevent the relevant processes from incurring fire and explosion accidents.