Structural properties of the titanium dioxide thin films grown by atomic layer deposition at various numbers of reaction cycles

A dependence of structural properties of TiO₂ films grown on both Si- and Ti-substrates by atomic layer deposition (ALD) at the temperature range of 250-300 °C from titanium ethoxide and water on the number of reaction cycles N was investigated using Fourier-transform infrared (FTIR) spectroscopy and X-Ray diffraction (XRD). TiO₂ films grown on both Si- and Ti-substrates revealed amorphous structure at low values of N < 400. However, an increase of N up to values 400-3600 resulted in the growth of polycrystalline TiO₂ with structure of anatase on both types of substrates and according to XRD-measurements the sizes of crystallites rose with the increase of N. The maximum anatase crystallite size for TiO₂ grown on Ti-substrate was found to be on ∼35% lower in comparing with that for TiO₂ grown on Si-substrate. A use of titanium methoxide as a Ti precursor with the ligand size smaller than in case of titanium ethoxide allowed to observe an influence of the ligand size on both the growth per cycle and structural properties of TiO₂. The average growth per cycle of TiO₂ deposited from titanium methoxide and water (0.052 ± 0.01 nm/cycle) was essentially higher than that for TiO₂ grown from titanium ethoxide and water (0.043 ± 0.01 nm/cycle). Ligands of smaller sizes were found to promote the higher crystallinity of TiO₂ in comparison with the case of using the titanium precursor with ligands of bigger sizes.     

Formation of copper islands on a native SiO2 surface at elevated temperatures

A combination of in situ X-ray photoelectron spectroscopy analysis and ex situ scanning electron- and atomic force microscopy has been used to study the formation of copper islands upon Cu deposition at elevated temperatures as a basis for the guided growth of copper islands. Two different temperature regions have been found: (I) up to 250 °C only close packed islands are formed due to low diffusion length of copper atoms on the surface. The SiO₂ film acts as a barrier protecting the silicon substrate from diffusion of Cu atoms from oxide surface. (II) The deposition at temperatures above 300 °C leads to the formation of separate islands which are (primarily at higher temperatures) crystalline. At these temperatures, copper atoms diffuse through the SiO₂ layer. However, they are not entirely dissolved in the bulk but a fraction of them forms a Cu rich layer in the vicinity of SiO₂/Si interface. The high copper concentration in this layer lowers the concentration gradient between the surface and the substrate and, consequently, inhibits the diffusion of Cu atoms into the substrate. Hence, the Cu islands remain on the surface even at temperatures as high as 450 °C.     

Preparation and electrochemistry of one-dimensional nanostructured MnO2/PPy composite for electrochemical capacitor

One-dimensional nanostructured manganese dioxide/polypyrrole (MnO₂/PPy) composite was prepared by in situ chemical oxidation polymerization of pyrrole in the host of inorganic matrix of MnO₂, using complex of methyl orange (MO)/FeCl₃ as a reactive self-degraded soft-template. The morphology and structure of the composite were characterized by infrared spectroscopy (IR) X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the MnO₂/PPy composite consists of α-MnO₂ and PPy with nanotube-like structure. Electrochemical properties of the composite demonstrated the material showed good electrochemical reversibility after 500 charge-discharge cycles in the potential range of −0.4 to 0.6 V, the tube-like nanocomposite has the potential application in electrochemical capacitor.     

Improved performance of TiO2 electrodes coated with NiO by magnetron sputtering for dye-sensitized solar cells

TiO₂ electrodes are coated with NiO by DC magnetron sputtering, and their structural, optical and electrochemical performance has been investigated. X-ray diffractometry (XRD), UV-vis spectrophotometry, scanning electron microscopy (SEM), AC impedance, and linear sweep voltammetry (LSV) are used to characterize the TiO₂/NiO electrodes. Their performance is evaluated with a computer controlled electrochemical workstation in combination with three conventional electrodes. The experimental results indicate that the surface modification of TiO₂ electrodes with sputtered NiO reduces trap sites on TiO₂ and improves the electrochemical performance of dye-sensitized solar cells (DSSCs). Sputtering NiO for 7 min, which is about 21 nm thick, on 6.5 μm thick TiO₂ greatly improves the DSSC parameters, and the conversion efficiency increases from 3.21 to 4.16%. Mechanisms of the influence of the NiO coating on electrochemical performance are discussed.     

Synthesis and Characterization of Cobalt-Carbon Core-Shell Microspheres in Supercritical Carbon Dioxide System

研究了钴碳核壳微球在超临界二氧化碳体系中的合成过程. 在密闭的不锈钢高压反应釜中,适量的二茂钴和干冰在350 oC下,反应12 h后合成直径大约1 μm的钴碳核壳微球。通过X射线衍射、X射线光电子谱、透射电子显微镜、傅利叶红外光谱(FT-IR)以及拉曼光谱的分析,钴碳核壳微球是由直径小于1 μm的非晶钴核和厚度约为200 nm的非晶碳壳组成. 其生长机理可能是：二茂钴在超临界二氧化碳体系中的热分解,带单电子的碳原子或基团由于磁性作用沉积在磁性的钴核上. 由于非晶碳壳的存在,钴碳核壳微球的磁饱和强度141.     

基于VO2薄膜非致冷红外探测器光电响应研究

VO₂薄膜是非致冷微测辐射热红外探测器热敏电阻材料.研究中应用微电子工艺制备了VO₂溅射薄膜红外探测器,在296K的环境中测试了该探测器在不同的直流偏置、光调制频率下对873K标准黑体源8—12μm红外辐射的光电响应以及器件的噪声电压,在10和30Hz的调制频率下其响应率分别大于17kV/W和接近10kV/W.该探测器实现了探测率D大于1.0×10⁸cm (Hz)^1/2/W,热时间常量为0.011s的8—12μm非致冷 关键词： 非致冷测辐射热探测器 红外探测器 二氧化钒 薄膜     

中温烟气脱硫过程中CO2对脱硫剂钙利用率的影响

本文在300～600℃的中温区段,实验研究了CO2在烟气脱硫过程中与钙基脱硫剂发生碳酸盐还原反应,削弱脱硫效果的规律,发现石灰钙利用率随温度升高呈跳跃式变化,并因碳酸盐反应程度的迅速增加而在500℃附近出现低谷.由此明确了减小碳酸盐反应效应,提高脱硫剂钙利用率的途径,为进一步发展中温烟气脱硫工艺提供了重要依据.     

Nanosized metal deposits on titanium dioxide for augmenting gas-phase toluene photooxidation

The build-up of intermediate species on the surface of TiO₂ during gas-phase toluene (C₇H₈) photodegradation has been observed to deactivate the photocatalyst. Nanosized metallic deposits on the TiO₂ surface may enhance the photocatalytic process and improve photocatalyst performance. In this study, noble (Ag, Au) and platinum group (Pt, Pd, Rh) metals, at a nominal loading of 0.5 at.%, were deposited onto Degussa P25 TiO₂ to enhance photocatalyst performance and inhibit deactivation. Pd, Rh and Au deposits delayed photocatalyst deactivation by a factor of 2, while Pt deposits delayed photocatalyst deactivation by a factor of 20, when compared with neat TiO₂. Ag deposits did not improve photocatalyst activity. Metal deposit performance was related to the work function of each metal, however, the Pt finding suggested that these effects are not governed solely by this aspect, but factors such as deposit characteristics and/or thermal catalytic properties of the metals may be influential.     

吸收波长和吸收效率可控的超材料吸收器

为了使超材料完美吸收器(metamaterial perfect absorber,MPA)能够同时实现吸收效率和吸收波长的控制,本文提出利用二氧化钒(VO2)和石墨烯作为MPA的材料,通过对MPA的结构设计,在红外波段实现了高吸收,吸收效率最高可达99％.研究发现通过改变VO2的温度和石墨烯的化学势,可同时实现MPA...     

θ环填料塔中单乙醇胺吸收CO2传质性能研究

在乱堆θ环不锈钢填料的自制填料塔中,使用单乙醇胺(MEA)作为吸收剂,研究MEA脱除CO2的去除率和总体积传质系数KGav,考察了贫液中CO2负载量、吸收剂浓度、液体流量、吸收温度等不同参数对总体积传质系数的影响.实验结果表明,KGav随贫液中CO2负载量的增大而减小,随吸收剂浓度、液体流量的增大而增大;且进料温度在3...