Operational characteristics and power scaling of a transverse flow transversely excited CW CO<Subscript>2</Subscript> laser

Transverse flow transversely excited (TFTE) CO₂ lasers are easily scalable to multikilowatt level. The laser power can be scaled up by increasing the volumetric gas flow and discharge volume. It was observed in a TFTE CW CO₂ laser having single row of pins as an anode and tubular cathode that the laser power was not increasing when the discharge volume and the gas volumetric flow were increased by increasing the electrode separation keeping the gas flow velocity constant. The discharge voltage too remained almost constant with the change of electrode separation at the same gas flow velocity. This necessitated revision of the scaling laws for designing this type of high power CO₂ laser. Experimental results of laser performance for different electrode separations are discussed and the modifications in the scaling laws are presented.     

A tentative approach to the direct simulation of drag reduction by polymers

An efficient technique for drag reduction uses dilute solutions of a few p.p.m. of polymers. A possible reduction in drag of up to 80% is achieved. Several experimental observations have been made which tend to indicate that the polymers modify the turbulence structures within the buffer layer. Flow visualisations have shown that the changes consist of a weakening of the strength of the streamwise vortices. Existing literature reveals no attempts of numerical simulation of this phenomenon. In this paper an approach is pursued by using a constitutive equation which relates the elongation viscosity to the local properties of the flow. According to this model this viscosity is large in zones where the amount of strain rate is greater than the amount of vorticity, and is zero when the vorticity exceeds the strain rate. Simulations have been performed in a “minimal channel” to give good resolution with a limited number of grid points. The accuracy of the method is tested by comparison with the results of other techniques. For simulations with polymers, quantitative comparisons cannot be made, but the results reproduce the qualitative outputs of the experiments. The mean streamwise velocity is modified in the buffer layer; the peak of the streamwise turbulent intensity, in wall units, increases and its maximum moves far from the wall; and the vertical turbulent intensity is largely reduced in the wall region. An interesting outcome from both the simulation and the experiments is that the strength of the longitudinal vortices is reduced when the polymers are present.     

基于遗传禁忌算法的双资源约束下并行生产线调度研究

并行生产线调度问题兼有并行机器和流程车间调度问题的特点,是一类新型的调度问题。在考虑遗传算法早熟收敛特性和禁忌搜索法自适应优点的基础上,将遗传算法和禁忌搜索法结合起来,提出了基于遗传算法和禁忌搜索算法的双资源并行作业车间的调度优化问题算法,即考虑到了产品的调度受到机器、工人等资源制约的影响,对算法中种群的构造,适应度计算,遗传操作等方面进行了研究,最后给出了实例仿真和结论。     

知识库中精确知识的判定算法

研究了知识库中挖掘它所包含的精确知识的方法，给出知识库的相关概念及精确知识的定义，讨论了一种在所定义的知识库中提取并判定精确知识的算法．     

Improved dust capture methods for crushing plant

The use of compressive crushing equipment such as gyratory crushers within minerals processing plants can potentially generate large quantities of dust. Remedies to this problem include the retrofitting of shrouds, enclosures, local exhaust ventilation (LEV) systems and water suppression systems. The single or combined application of these systems must be optimised to ensure they operate efficiently. It is desirable that the future design planning of such facilities include integrated dust suppression and/or removal systems to ensure material delivery rates are maintained and the welfare of the workforce is protected.     

多级轴流压气机全工况特性计算

本文使用三维粘性流动计算软件Fine／Numeca,对某十五级轴流压气机进行了内流流场和全工况特性的数值计算尝试。分析了该压气机在设计工况和非设计工况的性能,同时把整机计算结果和前七级叶片的计算结果进行了比较。计算结果表明,当计算的级数较少时,目前的软件和硬件平台可以比较合理地预测压气机的全工况特性;而当计算的级数较多时,准确的数值模拟仍需要更为准确的多级模型和数值方法。     

Thermal stability of shear-induced precursor structures in isotactic polypropylene by rheo-X-ray techniques with couette flow geometry

Combined in situ rheo-SAXS (small-angle X-ray scattering) and -WAXD (wide-angle X-ray diffraction) studies using couette flow geometry were carried out to probe thermal stabilty of shear-induced oriented precursor structure in isotactic polypropylene (iPP) at around its normal melting point (162 °C). Although SAXS results corroborated the emerging consensus about the formation of “long-living” metastable mesomorphic precursor structures in sheared iPP melts, these are the first quantitative measures of the limiting temperature at which no oriented structures survive. At the applied shear, rate = 60 s⁻¹ and duration t_s = 5 s, the oriented iPP structures survived a temperature of 185 °C for 1 h after shear, while no stable structures were detected at and above 195 °C. Following Keller's concepts of chain orientation in flow, it is proposed that the chains with highly oriented high molecular weight fraction are primarily responsible for their stability at high temperatures. Furthermore, the effects of flow condition, specifically the shear temperature, on the distributions of oriented and unoriented crystals were determined from rheo-WAXD results. As expected, at a constant flow intensity (i.e., rate = 30 s⁻¹ and duration, t_s = 5 s), the oriented crystal fraction decreased with the increase in temperature above 155 °C, below which the oriented fraction decreased with the decrease in temperature. As a result, a crystallinty “phase” diagram, i.e., temperature versus crystal fraction ratio, exhibited a peculiar “hourglass” shape, similar to that found in many two-phase polymer–polymer blends. This can be explained by the competition between the oriented and unoriented crystals in the available crystallizable species. Below the shear temperature (155 °C), the unoriented crystals crystallized so rapidly that they overwhelmed the crystallization of the oriented crystals, thus depleting a major portion of the crystallizable species and increasing their contribution in the final total crystalline phase. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3553–3570, 2006     

Reformulation of the support set selection problem in the logical analysis of data

The paper is concerned with the problem of binary classification of data records, given an already classified training set of records. Among the various approaches to the problem, the methodology of the logical analysis of data (LAD) is considered. Such approach is based on discrete mathematics, with special emphasis on Boolean functions. With respect to the standard LAD procedure, enhancements based on probability considerations are presented. In particular, the problem of the selection of the optimal support set is formulated as a weighted set covering problem. Testable statistical hypothesis are used. Accuracy of the modified LAD procedure is compared to that of the standard LAD procedure on datasets of the UCI repository. Encouraging results are obtained and discussed.     

Assessment of filtered gas–solid momentum transfer models via a linear wave propagation speed test

The propagation speeds of linear waves in gas–solid suspensions depend strongly on the solids volume fraction and the wave frequency. The latter is due to gas–solid momentum transfer and allows a simple test on filtered gas–solid momentum transfer models. Such models may predict linear wave propagation speeds different from those obtained with the non-filtered model at wave frequencies higher than the filter frequency, but not at wave frequencies lower than the filter frequency.     

Phase diagram of Na2S2O3 + ethanol + water at ambient pressure and temperature

In the present communication, we report the studies concerning liquid–liquid–solid equilibria for the ternary system sodium thiosulphate (Na₂S₂O₃) + ethanol + water at ambient pressure and at room temperature (303 ± 2 K). The solubility data of Na₂S₂O₃ are reported for solutions in water, ethanol and solutions of varying concentrations of ethanol in water. The phase diagram for the said system is developed, described and compared with similar system K₂CO₃ + methanol + water. These results have been explained in terms of structural properties of aqueous ethanol solutions and further discussed in terms of the effect of ions to cause phase separation.