Investigation of hypersonic nozzle flow uniformity using NO fluorescence

Planar laser-induced fluorescence visualisation is used to investigate nonuniformities in the flow of a hypersonic conical nozzle. Possible causes for the nonuniformity are outlined and investigated, and the problem is shown to be due to a small step at the nozzle throat. Entrainment of cold boundary layer gas is postulated as the cause of the signal nonuniformity. PACS 47.80.Jk, 47.40.Ki, 47.60.+i     

Optimal Planar Interception with Fixed End Conditions: Approximate Solutions

In a previous paper (Ref. 1), an exact solution of the optimal planar interception with fixed end conditions was derived in closed form. The optimal control was expressed as an explicit function of the state variables and two fixed parameters, obtained by solving a set of nonlinear algebraic equations involving elliptic integrals. In order to facilitate the optimal control implementation, the present paper derives a highly accurate simplified solution assuming that the ratio of the pursuer turning radius to the initial range is small. An asymptotic expansion further reduces the computational workload. Construction of a near-optimal open-loop control, based on the approximations, completes the present paper.     

有色金属冶炼厂回转干燥窑分布式控制系统

对于锌湿法冶炼过程中的回转干燥窑控制问题,本文提出一种温度场控制方案,它由负压控制、温度和煤气流量串级控制以及含氧量控制来实现。基于这个控制方案,一个回转干燥窑分布式控制系统已经建立在某有色金属冶炼厂。本文介绍控制系统设计中使用的理论和技术。     

离散边界条件系统的最优控制

研究离散边界条件系统的最优控制问题，给出了最优控制存在的必要条件，证明了此类系统最优控制仍有最大值原理成立。     

用正交试验法确定最佳调剖施工参数

针对文明寨油田地质特征和开采现状，按照油藏数值模拟原理，以调剖井对应油井的增油降水创经济效益大小为考核指标，运用正交试验的均衡分散性和整齐可比性及Ｌ９（３４），正交表进行调剖最佳施工参数试验．经现场试验、分析、讨论发现：影响调剖效果的主要因素是措施半径，其次为施工排量和注入方式，且最佳施工参数是措施半径在３．５ｍ左右，施工排量在１９ｍ３／ｈ左右，按连续注入方式调剖。经文明察油田、卫城油田、马寨油田５０井次现场试验证明，较好地改善了注水井吸水剖面，对应油井取得了明显的增油降水效果，收到了较好的经济和社会效益．     

动态校正的PI型广义预测控制器及其在反应釜系统中的仿真研究

提出了一种新型的广义预测控制器。由于在控制器的设计中,进行了预测误差的动态校正,并且控制器采用了比例积分型(PI)目标函数,因此该控制器对未建模动态具有很强的鲁棒性。应用低阶的模型对一个强放热的化学反应釜模型进行的仿真研究检验了该方法的有效性。     

压力淬火过程中锗的相结构研究

 应用高压原位差热方法，直接测量了压力下锗的固化参数─—固化温度与过冷度。高压差热信号表明，当压力大于3 GPa时，锗在凝固过程中可能发生结构相变。X射线结构分析表明，在最终的样品中除GeⅠ相外，还形成GeⅢ相和GeⅣ相。     

Numerical integration of ordinary differential equations on manifolds

Summary This paper is concerned with the problem of developing numerical integration algorithms for differential equations that, when viewed as equations in some Euclidean space, naturally evolve on some embedded submanifold. It is desired to construct algorithms whose iterates also evolve on the same manifold. These algorithms can therefore be viewed as integrating ordinary differential equations on manifolds. The basic method “decouples” the computation of flows on the submanifold from the numerical integration process. It is shown that two classes of single-step and multistep algorithms can be posed and analyzed theoretically, using the concept of “freezing” the coefficients of differential operators obtained from the defining vector field. Explicit third-order algorithms are derived, with additional equations augmenting those of their classical counterparts, obtained from “obstructions” defined by nonvanishing Lie brackets.     

一种新型自学习智能控制器研究

本文结合工程实践经验，基于传统控制方法和智能自学习控制思想，提出了一种切实可行的新型智能控制器，并应用锥稳定性定理为闭环系统建立了稳定性分析，给出了ｌ２稳定性结果。     

准移动闭塞系统的元胞自动机模型及列车延迟传播规律的研究

在NaSch模型的基础上，针对铁路交通的特点提出一种用于模拟准移动闭塞系统的元胞自动机模型.应用该模型模拟了准移动闭塞系统列车延迟传播的交通现象，分析了准移动闭塞系统中的轨道定位单元长度、发车时间间隔、初始延迟时间等因素对列车延迟传播的影响. 关键词： 元胞自动机 交通流 准移动闭塞