Influence of annealing and chain defects on the melting behaviour of poly(vinylidene fluoride)

The melting behaviour of poly(vinylidene fluoride) (PVDF) was investigated by differential scanning calorimetry (DSC) and small- and wide-angle X-ray scattering in order to study the influence of the chain defects content and of the temperature of annealing on the crystallization and melting behaviour.All the DSC scans show a double endotherm and the analysis of the data suggests that the low temperature endotherm is due to the melting of a population of thin lamellae, whose thickness increases during the annealing, but a high content of chain defects prevents the lamellar thickening and the main effect in this case is the crystallization of thin lamellae from a portion of polymer which did not crystallize during the quenching from the melt. Furthermore, the two melting endotherms, which are observed, can be partially ascribed to a melting-recrystallization process.Furthermore, stepwise isothermal cooling was performed in a differential scanning calorimeter followed by melting scans of fractionated PVDF samples to point out the possible presence of a series of endothermic peaks.     

Laser spectroscopic investigation of a new precursor-type polyparaphenylenevinylene

Optical, structural and morphological properties of thin films of polyparaphenylenevinylene (PPV) formed by an alkyl sulfinyl precursor route have been studied. Thin films were fabricated on an optical glass and on quartz glass either by spin-coating of the precursor solution or by layer-by-layer deposition using Langmuir–Blodgett technique. PPV precursor films were also spin-coated on gold-coated glass in order to study thin-film optical parameters by surface plasmon spectroscopy. We have been successful in forming about 40 precursor mono layers on quartz glass by Langmuir–Blodgett technique using optimized surface pressure and dipping conditions. After thermal conversion of the precursor layers good quality fluorescent PPV films of yellow colour have been obtained. Optical characterization of the films was carried out by linear absorption and emission spectroscopy, ellipsometry, and surface plasmon spectroscopy. Structural and morphological studies on the thin films were carried out by using X-ray scattering and atomic force microscopy. Wave-guided travelling-wave laser action has been achieved in a PPV film on quartz glass. The sample was transversally pumped with picosecond laser pulses (wavelength 347.15 nm, duration 35 ps). Laser emission occurred at 550 nm for pump pulse energy densities above .     

激光水下扫描成像系统的图像修正机理

同步扫描系统可以克服后向散射，但同时也产生了两种非线性，一是扫描线速度的非线性，一是由于距离对光能衰减造成的非线性，两种非线性都需要修正，本文从原理上讨论水下激光成像时能量衰减的修正原理与修正方法，并给出仿真结果。     

Changes in the Laser-Induced Fluorescence Spectrum of Myocardium Tissue with Decrease in Its Viability

We investigated the laser-induced fluorescence spectra (LIF) of porcine cardiac tissues with different degrees of viability. The data obtained are compared with the results of routine histological investigations and also with the experiments performed with the use of fluorescent probes. It has been found with a high degree of reliability that the loss of the viability of the myocardium tissue leads to the alteration of its LIF spectra. This can be used for low-invasive rapid control of transplant viability in the process of its preparation and during surgery.     

Submicrometric Displacement and Vibration Measurement Using Optical Feedback in a Fiber Laser

A very simple and efficient technique for the remote sensing of a noncooperative target is presented. This technique is based on the frequency-shifted reinjection of light in a class B laser. Ytterbium- and erbium-doped fiber lasers have both been used to measure displacements with a submicrometric resolution and the vibration power spectrum of an object.     

蓝光相变光盘的多层膜结构设计

为了使光盘获得优良的记录／读出性能并能够长期稳定地使用，必须优化设计相变光盘的多层膜结构。采用自行设计的模拟分析相变光盘读出过程设计软件，从光学角度出发模拟计算了蓝光(405nm)相变光盘的膜层结构，研究了多层膜系的反射率和反射率对比度等光学参量与各层膜厚度和槽深的关系。研究得出的最佳多层膜结构为：下介电层／记录层／上介电层／反射层的厚度对于台记录为100nm／10nm／25nm，／60nm，而对于槽记录则为140nm／15nm／30nm，／60nm，槽深为50nm。模拟计算结果对于将来高密度蓝光相变光盘的制备具有一定的指导意义。     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

毛细管放电X光激光装置中的预脉冲电源

 针对目前毛细管放电X 光激光装置产生的预脉冲电流幅值过大、持续时间较短的问题，提出了增加预脉冲开关抑制原有预脉冲，再外加由脉冲成形网络组成的预脉冲发生器，产生所需预脉冲的改造方案。可在主脉冲来临之前产生幅度10~50A，持续时间约17μs的方波预脉冲电流，来满足毛细管放电泵浦类氖氩X光激光实验的需要。     

液晶显示器用导电粉的扫描电镜图像

液晶显示器用导电粉的形状、尺寸及偏差对于液晶显示屏的质量控制来说是非常重要的。论述了液晶显示器(LCD)用导电粉的作用和性能要求。给出了液晶显示器用导电粉的扫描电镜图像。该图像对观测导电粉的粒径分布、导电粉在导电点中的浓度和分析导电点缺陷、提高液晶显示器的产品质量具有一定的意义。     

一种控制掺铒光纤激光器超混沌的方法——非线性延时反馈参数调制法

提出一种非线性延时反馈参数调制法来控制混沌/超混沌，给出了利用这种方法控制处于超混沌状态的双环掺铒光纤激光器的方案.数值模拟表明，只要延时时间和反馈强度合适就可以把双环掺铒光纤激光器从超混沌状态成功地控制到不同的周期状态. 关键词： 掺铒光纤激光器 超混沌 非线性延时反馈参数调制 混沌控制