高静态动作压力下粉尘爆炸泄放标准的可靠性

粉尘爆炸泄放设计标准的可靠性对能否实现爆炸防护尤为关键.以中径70μm石松子粉尘为介质,采用20 L球形粉尘爆炸装置进行了4种泄放口径、静态动作压力在0.12~0.6 MPa的爆炸泄放实验,对比了实验值与NFPA 68和EN 14491计算值.结果表明,NFPA 68在预测高静态动作压力下的泄放面积时,随着泄放口径的增大,预测结果由保守变为危险,但预测结果精度较好且数值稳定;EN 14491在预测高静态动作压力下的泄放面积时非常保守,预测精度较差,数据不可靠.依据两种标准推荐的经验函数关系,分析了NFPA 68和EN 14491在预测高静态动作压力时产生这种差异的原因.     

Bis-tridentate IrIII Phosphors Bearing Two Fused Five-Six-Membered Metallacycles: A Strategy to Improved Photostability of Blue Emitters

Iridium complexes bearing chelating cyclometalates are popular choices as dopant emitters in the fabrication of organic light-emitting diodes (OLEDs). In this contribution, we report a series of blue-emitting, bis-tridentate Ir^III complexes bearing chelates with two fused five-six-membered metallacycles, which are in sharp contrast to the traditional designs of tridentate chelates that form the alternative, fused five-five metallacycles. Five Ir^III complexes, Px-21 – 23 , Cz-4 , and Cz-5 , have been synthesized that contain a coordinated dicarbene pincer chelate incorporating a methylene spacer and a dianionic chromophoric chelate possessing either a phenoxy or carbazolyl appendage to tune the coordination arrangement. All these tridentate chelates afford peripheral ligand–metal–ligand bite angles of 166–170°, which are larger than the typical bite angle of 153–155° observed for their five-five-coordinated tridentate counterparts, thereby leading to reduced geometrical distortion in the octahedral frameworks. Photophysical measurements and TD-DFT studies verified the inherent transition characteristics that give rise to high emission efficiency, and photodegradation experiments confirmed the improved stability in comparison with the benchmark fac-[Ir(ppy)₃] in degassed toluene at room temperature. Phosphorescent OLED devices were also fabricated, among which the carbazolyl-functionalized emitter Cz-5 exhibited the best performance among all the studied bis-tridentate phosphors, showing a maximum external quantum efficiency (EQE_max) of 18.7 % and CIE_x,y coordinates of (0.145, 0.218), with a slightly reduced EQE of 13.7 % at 100 cd m⁻² due to efficiency roll-off.     

QEPAS系统中石英音叉模态仿真计算与研究

对石英音叉增强型光声光谱(QEPAS)系统中常用的石英音叉进行了有限元模态计算，获得石英音叉前6阶振型与模态频率，认知了第4阶对称摆动振型为有效振动，利用单因素法分析了石英音叉的音臂长度l₁、音臂宽度w₁、音臂厚度t、音臂切角θ、音臂圆孔直径d及音臂圆孔高度h对低阶有效共振频率(Fre)的影响，敏感度依次为： l₁> w₁>d>θ>t>h，考虑实际设计情形，筛选出了l₁，w₁，d与h四个石英音叉设计变量，采用Box-Behnken实验设计方案与RSM(response surface methodology)方法，以Fre为函数目标，建立l₁，w₁，d与h的二次回归响应面模型，得到了参数之间的交互作用，利用Design-Expert软件对响应面模型进行设计参数反求，结果表明，在15 000 Hz≤Fre≤25 000 Hz计算区域内误差较小，基本满足QEPAS系统的计算需求，所提出的研究与设计方法具有一定通用性，可为QEPAS系统中石英音叉结构参数设计提供参考。     

建筑物地基处理的设计与施工探讨

以具体工程为例，介绍了建筑物地基处理的设计、施工中遵循的原则，施工中遇到特殊情况时采取的处理方法和必要的检测方法，对几种桩基的设计要求、施工工艺及过程、质量控制等情况进行了简单阐述。     

任职经济责任审计系统设计与实现

该系统严格遵照国家干部经济责任审计的有关准则与规定，能够对企事业单位、行政单位等不同部门各个层次的领导干部，从内控制度、管理、经营、财务等多方面、多角度、全方位地进行跟踪审计，客观公正、实事求是地对有关报表数据进行科学分析，恰如其分地认定干部实绩和经济责任。     

物流系统容错设计方法

在相关理论的指导下，提出了物流容错技术的基本概念，论述了常见的系统故障、典型的容错设计方法和故障检测手段，讨论了物流容错技术的应用前景和发展方向。     

论住宅户型设计

为适应现代人居住观念的变化，结合设计工作的实践，分别就住宅户型设计中的户内空间序列以及起居室、卧室、厨房、卫生间的设计理念、设计原则和有关具体问题进行了探讨。     

Improved spacer design and cost reduction in an electrodialysis system

In electrodialysis using thin membranes and spacers, the compactness of the membrane cell-pairs leads to a small potential drop, and hence to energy saving. The spacer design itself has a great effect on the cost of the plants, since spacers act as turbulence promoters. A careful design, to increase the mass transfer coefficients, can reduce the membrane surface area required for a given application. Limiting current measurements, cell-pair resistance and pressure losses are presented for several thin spacers, for different flow-velocity values and feed water concentrations. It was possible to find an advantageous geometry of the separating mesh leading to substantial savings on investment and operation costs.     

固体力学有限元体系的结构拓扑变化理论

本文是文[1]的继续.文[1]提出了杆件系统的结构拓扑变化理论和拓扑变化法本文将这一理论和方法推进到连续体有限元体系;且在此基础上揭示出有限元体系的一个新性质,称为基本位移之梯度的正交性定理,从而给出一套设计敏度的显式表达式,可直接用于计算.     

在管理信息系统中单据设计的新方法

在分析PowerBuilder中用户对象的基本概念与特点基础上，提出了利用用户对象技术实现MIS(管理信息系统)中单据设计功能的方法，并给出了详细的实现过程。实际应用表明，该方法可使用户按企业的实际需要对单据的录入界面进行自由设计，无需修改软件即可满足不同用户的需求，适合各种管理信息系统的单据设计，具有通用性。