相变材料在装配式复合墙体日光温室中的应用研究

为进一步提高日光温室墙体的蓄热能力,改善室内热环境,对石蜡-膨胀珍珠岩复合相变材料（paraffin-expanded perlite composite phase change material,PCM-PE）在温室中的应用进行研究。利用TRNSYS（transient system simulation program）建立装配式复合墙体日光温室的模型,用晴天和阴天的实测数据验证模型准确性,利用该模型分析温室的北屋顶、侧墙、北墙等结构内表面分别添加PCM-PE后室内温度的变化和单位成本,及温室北屋顶、侧墙和北墙均添加PCM-PE时的最佳厚度。结果表明：温室不同结构内表面添加PCM-PE均对室内平均温度有明显提升作用,侧墙内表面添加PCM-PE使晴天时室内平均温度提高1.32 ℃,单位成本最低,为2 094元/℃;北屋顶、侧墙、北墙均添加PCM-PE时,其最佳厚度为50 mm,晴天室内平均温度和北墙平均温度分别提升3.9和3.7 ℃,阴天分别提升2.2和2.3 ℃;添加50 mm PCM-PE后,温室墙体传热系数较试验温室降低了15%,热阻提高了9.9%,对维持室内温度、降低温室能耗具有积极作用。分析温室不同结构应用PCM-PE的效果,同时考虑单位成本,可为建造经济性好、蓄热性能强的温室提供参考。     

SUS441不锈钢/Al金属间化合物微叠层复合板的界面结构与力学性能

采用“表面预处理—交替层叠—热轧复合—热处理”的工艺流程制备了SUS441不锈钢/Al金属间化合物微叠层复合板。利用光学显微镜、X射线衍射仪、扫描电子显微镜等检测与表征方法研究了热处理温度对复合板界面形貌、微观组织、物相组成、维氏硬度、拉伸性能的影响。结果表明：复合板界面结合良好;热处理后,固–液反应界面氧化严重,易导致界面分层而开裂;固–固、固–半固、固–液热处理后,金属间化合物层由均匀层和两相层组成,均匀层的物相组成为Fe₂A1₅,两相层的物相组成为Fe₄Al₁₃和Al₁₃Cr₂,且两相层具有韧性特征,固–半固反应所得到的复合板的综合力学性能最佳。     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

金属/电介质颗粒复合介质光学双稳的温度效应

应用有效媒质近似，结合自洽平均场理论和谱表示方法，研究了金属电介质颗粒复合介质的光学双稳行为与温度的关系.数值计算了不同的入射频率、体积分数和形状因子下光学双稳的温度效应，结果发现，温度对光学双稳的产生、双稳阈值及阈值宽度有很大影响. 关键词： 复合介质 光学双稳 谱表示 温度     

Electrolytical production of Ni + Mo + Si composite coatings with enhanced content of Si

Ni + Mo + Si composite coatings were prepared by co-deposition of nickel with molybdenum and silicon powders from a nickel solution in which Mo and Si particles were suspended by stirring. The layers have been deposited on a carbon steel substrate (St3S) under galvanostatic conditions. The content of Si in deposited layers was about 2-5 wt.% depending on deposition current density and the value of electric charge. For comparison Ni + Mo composite coatings were obtained under analogous current conditions. Composite coatings of enhanced Si content (15 wt.%) were deposited from an electrolyte in which 40 g/dm³ of Si covered with electroless plated nickel was dispersed. Deposition current density was equal 0.1 A/cm² and the value of electric charge Q = 500 C/cm². The thickness of the coatings was about 100-300 μm depending on their kind, electric charge and the deposition current density. Surface and cross-section morphology were investigated by scanning electron microscope (SEM). All deposited coatings are characterized by great, developed surface area. No internal stresses causing their cracking were observed. Chemical composition of the layers was determined by X-ray fluorescence spectroscopy (XRF) method and quantitative X-ray analysis (QXRD). It was stated, that the content of molybdenum and silicon in Ni + Mo + Si coatings depends on deposition current density and the amount of the powder in bath. The results of structural investigation of the obtained layers by the X-ray diffraction (XRD) method show, that they consist in crystalline Mo or Mo and Si phases built into Ni matrix. Moreover, Ni + Mo + Si composite coatings were modified by thermal treatment. It has been found that the thermal treatment of Ni + Mo + Si composite coatings caused that the new phases (NiSi, Mo₂Ni₃Si and Ni₆Mo₆C_1.06) were obtained.     

Mild synthesis of a Zn(II) metal organic polymer and its hybrid with activated carbon: Application as antibacterial agent and in water treatment by using sonochemistry: Optimization,kinetic and isotherm study

In this work, a room temperature and short method (30 min) for synthesis of nanosized rod-like metal organic polymer (MOP) has been described. Reaction of 1,4-phenylenedioxy diacetic acid with zinc salt leads to the formation of [Zn(C₁₀H₈O₆)(H₂O)₄]_n and subsequently was loaded on activated carbon following sonication and structurally characterized by FTIR, SEM, EDX and XRD analysis. The combination of this new composite with sonication was applied for rapid and efficient adsorption of Bromocresol Purple (BCP). Effects of initial BCP concentration, mass of adsorbent and sonication time on response were investigated and optimized by central composite design (CCD). Analysis of variation (ANOVA) was adapted to experimental data to find best optimum conditions which was set at 15.22 mg L⁻¹, 2.41 min, 0.02 g and 0.009 mg for initial BCP concentration, sonication time and adsorbent mass, respectively. Conduction of similar experiments at specified condition permit achievement of 98.69% removal percentage. 1,4-phenylenedioxy diacetic acid and Zn(NO3)₂.4H₂O which have applied for preparation of MOP are interesting antibacterial properties and accordingly MOP was screened in vitro for their antibacterial actively against Proteus vulgaris bacteria and experimental results reveal this MOP was able to inhibit growth of the tested bacteria. The experimental data were best fitted by pseudo-second order and Langmuir for kinetic model and the adsorption equilibrium isotherm, respectively.     

Microfabrication of stacks of acoustic matching layers for 15 MHz ultrasonic transducers

This paper presents a novel method used to manufacture stacks of multiple matching layers for 15 MHz piezoelectric ultrasonic transducers, using fabrication technology derived from the MEMS industry. The acoustic matching layers were made on a silicon wafer substrate using micromachining techniques, i.e., lithography and etch, to design silicon and polymer layers with the desired acoustic properties. Two matching layer configurations were tested: a double layer structure consisting of a silicon–polymer composite and polymer and a triple layer structure consisting of silicon, composite, and polymer. The composite is a biphase material of silicon and polymer in 2-2 connectivity. The matching layers were manufactured by anisotropic wet etch of a (1 1 0)-oriented Silicon-on-Insulator wafer. The wafer was etched by KOH 40 wt%, to form 83 μm deep and 4.5 mm long trenches that were subsequently filled with Spurr’s epoxy, which has acoustic impedance 2.4 MRayl. This resulted in a stack of three layers: The silicon substrate, a silicon–polymer composite intermediate layer, and a polymer layer on the top. The stacks were bonded to PZT disks to form acoustic transducers and the acoustic performance of the fabricated transducers was tested in a pulse-echo setup, where center frequency, −6 dB relative bandwidth and insertion loss were measured. The transducer with two matching layers was measured to have a relative bandwidth of 70%, two-way insertion loss 18.4 dB and pulse length 196 ns. The transducers with three matching layers had fractional bandwidths from 90% to 93%, two-way insertion loss ranging from 18.3 to 25.4 dB, and pulse lengths 326 and 446 ns. The long pulse lengths of the transducers with three matching layers were attributed to ripple in the passband.     

Preparation, structures and photoluminescent enhancement effect of PbWO4–TiO2 composite nanofilms

A novel route for preparing PbWO₄–TiO₂ nanofilms on a glass substrate is firstly proposed. The collodion is used as a dispersant and film-forming agent. The nanofilms are characterized through SEM, XRD, TG/DTA, PL and IR, respectively. The results of XRD indicate PbWO₄ particles with tetragonal scheelite structure and TiO₂ particles with Anatase phase, and SEM shows they are well dispersed in the substrate. Compared with nanoparticles, when TiO₂ nanoparticles are added in 5% ratio, the PL intensities at 395 nm of PbWO₄ nanofilms are enhanced obviously. IR spectrum reveals a large absorption band between 750 and 870 cm⁻¹, which is the W–O stretching vibration in WO₄ tetrahedron.     

Trace determination of safranin O dye using ultrasound assisted dispersive solid-phase micro extraction: Artificial neural network-genetic algorithm and response surface methodology

In this study, ultrasound assisted dispersive solid-phase micro extraction combined with spectrophotometry (USA-DSPME-UV) method based on activated carbon modified with Fe₂O₃ nanoparticles (Fe₂O₃-NPs-AC) was developed for pre-concentration and determination of safranin O (SO). It is known that the efficiency of USA-DSPME-UV method may be affected by pH, amount of adsorbent, ultrasound time and eluent volume and the extent and magnitude of their contribution on response (in term of main and interaction part) was studied by using central composite design (CCD) and artificial neural network-genetic algorithms (ANN-GA). Accordingly by adjustment of experimental conditions suggested by ANN-GA at pH 6.5, 1.1 mg of adsorbent, 10 min ultrasound and 150 μL of eluent volume led to achievement of best operation performance like low LOD (6.3 ng mL⁻¹) and LOQ (17.5 ng mL⁻¹) in the range of 25–3500 ng mL⁻¹. In following stage, the SO content in real water and wastewater samples with recoveries between 93.27–99.41% with RSD lower than 3% was successfully determined.