Hydroxyapatite coating on porous silicon substrate obtained by precipitation process

Hydroxyapatite Ca₁₀(PO₄)₆(OH)₂ (HAP) is known as a bioactive and biocompatible material, HAP coatings were used to improve the biocompatible of substrate by many researcher, In this work, HAP thin films on porous silicon (PS) substrates have been prepared by aqueous precipitation method with rapid thermal annealing (RTA) processes. The HAP films had been prepared under the annealing temperature ranging from 300 to 1000 °C. By the measurement of X-ray diffraction (XRD), it was found that for the crystallinity optimization, the heat-treatment at 850–950 °C for 1 h would be favorable. Atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements reveal a dense and smooth surface of the HAP film, and tightly adherence of the coating on porous silicon substrate after sintered. Thus, by this method, porous silicon could be increased its bioactivity and so that could be used in the biomedical area.     

活塞环表面碳化铌镀覆新工艺试验研究

用化学液相沉积方法，在高强度灰铸铁活塞环表面实现了Ｎｂｃ覆层，盘销磨擦磨损试验表明，无论在无润滑的情况时，Ｎｂｃ镀层表面要比镀Ｃｒ表面或铸铁原始表面具有更高的耐磨性，可以延长活塞环使用寿命，而Ｎｂｃ镀层与铸铁之间低的磨擦系数可使Ｓ１９５柴油机磨擦损失降低０．３５ｋＷ，降低比油耗９－５ｇ／（ｋＷ．ｈ）。     

气密性碳涂覆光纤筛选强度与电阻关系研究

通过实验分析确立了把光纤电阻作为衡量气密性碳涂覆光纤通过２％应变筛选的过渡标准。要拉制２％应变筛选的碳涂覆光纤，其电阻值应小于３０ｋΩ／ｃｍ。     

对煤矿岩体中固流耦合效应问题研究的探讨

本文对固流耦合效应的基本概念、基本原理进行了简单介绍。并对采动影响下邻近煤层、岩层的瓦斯向本层采空区的流动规律,以及煤和瓦斯突出的机理和发生的理论,分别作为固流耦合效应的两类不同问题进行了研究.同时提出了今后进行进一步研究的看法。     

端羟基聚二甲基硅氧烷缩聚固化涂膜的“等当点”特性

实验发现,线型端羟基聚二甲基硅氧烷与固化剂发生聚缩反应而固化成膜时,在“等当点”膜表面有最强的疏水性。且对同一种端羟基聚二甲基硅氧烷,“等当点”随固化剂官能度而改变。     

水性涂料用聚丙烯酸酯微乳液的合成及其表征

低污染、低能耗的乳液涂料在建筑涂料中得到了广泛应用,具有核壳结构的聚合物乳液对胶膜的力学性能有较大的改善[1],微米(或纳米)级乳液具有优异的成膜性能,两者均是近年来高分子材料科学中发展十分迅速的新领域[2]。但微乳液聚合时乳化剂用量大,单体含量少。本文采用阴非离子复合乳化剂体系,单体预乳化工艺,种子乳液聚合法,通过正交实验优化聚合工艺参数及体系配方,合成了纳米级聚丙烯酸酯微乳液。并对乳液聚合物的粒径及分布、热性能、分子量及分布、结构等进行了表征。1　实验部分1 1　主要原料及乳液表征苯乙烯(St)、甲基丙烯酸甲…     

有机硅耐磨透明涂层的固化分析

ＦＴＩＲ、ＴＧ、ＴＢＡ等对有机硅耐磨涂料（有机硅溶胶）的热固化过程研究表明有机硅胶体中缔合羟基间的脱水缩合速率很高；羟基脱水程度与固化温度有关，温度越高，达平衡时羟基的浓度越低，在１０５～１３０℃间羟基的浓度变化最大，加入适当的固化剂，对羟基的脱水交联有促进作用，在较高的固化温度下，反应体系中出现了环氧环异构化产生的酮羰基的吸收峰     

Tribological properties of ormosil coatings

Transparent plastics are not scratch resistant. The damage leads to a loss of optical properties. Coatings prepared using either tetraethoxysilane or colloidal silica particles embedded in glymo is a way to avoid these disadvantages. Tribological experiments are carried out to better understand the surface modification due to a sliding friction. It is shown that the wear track is not directly related to usual mechanical properties such as Young's modulus and the hardness of the coating. The different stages leading to material loss are discussed in term of particle removal and debris circulation (accumulation or elimination) through the friction track. The mechanical properties of the film combined with the film to substrate adhesion are expected to play an important role as it can be deduced from results obtained as a function of the coating composition.     

A scratch-resistant single-layer antireflective coating by a low temperature sol-gel route

A novel quarterwave-thick narrow-bandwidth antireflective coating has been developed for both plastic and vitreous substrates by a sol-gel route. This coating has revealed pronounced scratch- and climatic-resistance under adverse conditions. The single-layer coating consists basically of a composite material made of silica as the discontinuous phase and of a polytetrafluoroethylene-derived (Teflon¹) organic polymer as the continuous phase. This leads to fluorine-containing colloidal silica product, or a so-called Flucosil coating. The coating is applied by spinning or dipping from specific solutions at room temperature followed by a mild and short heat treatment. In addition to remarkable abrasion and environmental resistance properties, such coatings have displayed excellent laser-induced damage threshold levels, surpassing uncoated substrates.We hope such a product might open new perspectives concerning household articles, architectural optical thin-films, ophthalmic uses, and so on.     

Determination of cake thickness and porosity during cross-flow ultrafiltration on a plane ceramic membrane surface using an electrochemical method

The thickness and the porosity of a deposit during ultrafiltration experiments are determined using an electrochemical method. Twenty microelectrodes are mounted flush to a ceramic plane membrane and maps of deposit thickness are determined for three inlet/outlet distributors configurations. Combining an electrochemical method and a step transient method, the determination of the thickness and the porosity of a particles deposit is performed. These local thickness and porosity values are analyzed thanks to wall shear stress local measurements obtained in a previous work [Sep. Sci. Technol. 37 (10) (2002) 2251]. The results emphasize the heterogeneity of the deposit thickness, especially in zones of low wall shear stress. Furthermore, the porosity values of the deposit are ranged between 0.3 and 0.8 as a function of the location at the membrane surface.