测接触角法确定偶联剂的最佳用量

偶联剂是一类能在无机填料和聚合物基材之间形成“分子桥”、改善两者之间相容性或提高两者之间相互作用能力的化合物。将经偶联剂改性的无机填料填充到聚合物中可以制得成本低、性能好的复合材料。由于偶联剂用量多少将对复合材料的性能产生较大影响,因此建立一种准确、简便地确定偶联剂最佳用量的方法有着十分重要的理论和实际应用意义。     

Electrokinetic and contact angle measurements of grafted carbon fibers

 The grafting method that has successfully been applied to methacrylic acid and liquid crystalline monomers was expanded to prepare amphoteric carbon fiber surfaces using 2-(N,N-dimethylamino)ethyl methacrylate as monomer. The obtained carbon fiber surfaces were characterized by contact angle and ζ-potential measurements. The expected basic behavior was not observed, instead an amphoteric character of the modified carbon fiber surface was found. The fiber surfaces display a basic character in the acidic pH-range, while they are acidic in the alkaline part of the pH-scale. An important influence is derived from the amount of initiator used to graft the monomers onto the fibers. The smaller the initiator concen-tration used during polymerization, the larger the amount of amino functionalities introduced to the carbon fiber surface. The wetting behavior versus water depends on the overall conformation of the immobilized polymer. During immersion into water the polymer acts hydrophobic, while during emersion, a hydrophilic character is observed, probably derived from conformational changes and swelling during the contact angle measure-ments in water. Received: 9 June 1998 Accepted: 13 August 1998     

Studies on the phase properties of lyotropic liquid crystals of Brij35/sodium oleate/oleic acid/water system:By means of polarizing microscope,SAXS,~2H-NMR and rheological methods

The pseudo-quaternary phase diagram of Brij35/sodium oleate/oleic acid/water systems has been investigated, and the liquid crystal area has been identified, which covers about two thirds of the whole phase diagram. The liquid crystal structure and behavior have been also studied by using polarizing texture, small angle X-ray scattering, 2H-NMR and rheometer etc. The result shows that when the composition of the system changes along the line of AA′ in this large liquid crystal region, the structural change is cubic→cubic/lamellar→lamellar→lamellar/hexagonal→hexagonal. Meanwhile, we made the first attempt of systematic study of the rheological properties of the above system. The lattice constants of cubic and hexagonal liquid crystals are 10.53 and 5.68 nm, respectively.     

精制煤液化中油加氢裂化制取喷气燃料的研究

在实验室固定床反应装置上,选用Mo-Ni-P/Si-Al工业催化剂,对精煤液化中油进行了加氢裂化制取喷气燃料的实验。考察了反应温度、空速对芳烃加氢转化及产品馏分分布的影响。通过加氢裂化,降低了油品芳烃含量,提高了喷气燃料馏分的收率。在总压为15MPa,反应温度为350—360℃,空速为0.8—1.0h~(-1)条件下,获得了芳烃含量低于10w%的低结晶点的优质喷气燃料产品。并对煤液化中油制取的喷气燃料的组成和性质进行了分析和评价。     

煤炭液化复合铁系催化剂的研究

用微型高压釜,以杂酚油为溶剂,在反应温度400℃,氢初压6.08MPa,反应时间30分钟的条件下,研究了多种含铁矿物质、复合铁系催化剂对煤炭液化的催化效果。并用高压DTA技术进一步证实了复合铁系催化剂的良好液化加氢活性。     

抚顺烟煤及其抽出物的FTIR光谱结构表征

用富立叶变换红外光谱(FTIR)对抚顺烟煤的有机组分进行了测定。通过对谱图的解析,指出抚顺烟煤及其吡啶抽出物和抽提残煤在结构上的异同。以及抽出物各色谱馏分中存在的官能团和官能团之间极性的差异,对原煤整体结构提供了精细的结构信息。     

纳派林类二萜生物碱研究

纳派林类化合物是一类重要的二萜生物碱,本文概述了此类化合物的化学结构,波谱特征及某些化学反应,着重介纠~1H慢~13C NMR 的特征。并列表说明所有已知的天然存在的纳派林类化合物的结构、理化性质及植物来源等。     

缓慢炭化部分氧化对制备煤质活性炭的影响

研究了炭化升温速度、炭化低温区引入空气部分氧化对活性炭制备过程中炭化阶段、炭化物结构、活性炭性能等的影响。结果表明，炭化时低温部分氧化可提高炭化物得率，使炭化物微晶的ｄ００２值升高和Ｌｃ值减小；而较慢的炭化升温速度有利于制备优质活性炭。缓慢炭化、部分氧化可以在一定程度上控制炭化路径，使炭化向生成取向性差、难石墨化、各向同性、呒定形炭多的炭化物的方向进行；并讨论了它们控制炭化的作用机理。以此为指导，     

氧弹分解-原子荧光法测定煤中汞的研究进展

介绍氧弹分解-原子荧光法测定煤中汞含量的研究进展。影响该方法主要因素为称样量、氧气浓度、吸收剂、还原剂、煤种以及灰分含量。分别综述了各个因素对该方法的影响,可为相关标准的制定提供参考。该方法能够简单、经济、快速地测定煤中汞的含量,但是目前学者们对于该方法的相关研究还存在分歧,需要进一步的研究验证;同时,还需要注意以下几个研究方向:吸收剂和还原剂的选择对汞回收率的影响;吸收剂在密闭氧弹中对汞的回收率及吸收时间的研究;氧弹废气中汞含量的测定;煤种和灰分含量对汞含量测定的影响。     

ELECTROSPRAYING/ELECTROSPINNING OF POLY(γ-STEARYL-L-GLUTAMATE): FORMATION OF SURFACES WITH SUPERHYDROPHOBICITY

  Electrospraying/electrospinning of poly(γ-stearyl-L-glutamate) (PSLG) was investigated on a series solutions with different concentrations in chloroform. Field emission scanning electron microscopy (FESEM) and attenuated total reflectance Fourier transform infrared spectroscopy (FT-IR/ATR) were used to characterize the morphology and structure of the electrosprayed/electrospun polypeptide mats. It was found that electrospraying of PSLG with concentrations lower than 16 wt% afforded beads, while microfibers could be electrospun at the concentration of 22 wt%. The hydrophobicity of the electrosprayed/electrospun PSLG mats was investigated with static water contact angle (WCA) and tilt angle measurements. It was demonstrated that the superhydrophobic surfaces of PSLG with WCAs and tilt angles in the ranges of 150°-170° and 16.5°-4.2°, respectively, were obtained through electrospraying/electrospinning process.