磺化丁基橡胶离聚体在混合溶剂中的聚集行为

用顺磁共振（ESR）谱和粘度法考察了磺化丁基橡胶离聚体在二甲苯／正己醇混合溶剂中的聚集行为．ESR谱表明离聚体的离子基团发生聚集，其聚集程度受极性共溶剂（正己醇）的影响．粘度考察表明，在不同的浓度时离子基团有不同的聚集形式，低浓度时以分子内聚集为主，高浓度时以分子间聚集为主．离聚体的聚集度（DA）与浓度（c）的关系可用经验式DA＝Aexp（kc2）表示，其中A、k为常数．k值反映聚集度受浓度影响的程度，醇含量增大时k值减小，这是因为醇对离子的溶剂化作用导致离子聚集的倾向减小．     

Mechanical properties of fiber reinforced styrene-butadiene rubbers using surface-modified UHMWPE fibers under EB irradiation

Aiming to develop a high performance fiber reinforced rubber of SBR, a special technique using electron beam (EB) irradiation-induced graft-polymerization was applied to ultra-high molecular-weight polyethylene (UHMWPE) fibers. Although UHMWPE is chemically inert, N-vinyl formamide (NVF) could be graft-polymerized onto the UHMWPE fiber surface with this special technique. A maximum grafting percentage of 23.6% was achieved. The composite of SBR and grafted UHMWPE fibers with maximum grafting indicated a linear increase in the initial modulus and strength with the fiber content. At the fiber content of 10%, the initial modulus was improved about five times with respect to that of the pure SBR, while the strength was done about twice. At this moment, only a small reduction could be observed in the strain compared with that of pure SBR. The fiber reinforced rubber with a good performance was obtained in the system of SBR and grafted UHMWPE fibers.     

Surface Modification of Nitrile Rubber by Plasma Polymerization

Radio frequency plasma polymerization of vinylidene fluoride was used to modify the surface properties of nitrile rubber. The chemistry and frictional properties of the plasma films were characterized. FTIR transmission spectra and EDX analysis of plasma polymer films deposited on NaCl windows showed that the degree of fluorination of the plasma polymers increased as plasma power was increased from 25 to 50 W, and then decreased monotonically at higher powers. An estimation of the actual F/C ratio from EDX data indicated that the plasma polymer films contained approximately one fluorine atom for every 2–5 carbon atoms. Sliding friction tests on a Delrin countersurface showed that the coefficient of friction of the plasma treated rubbers was lower than untreated rubber, but slighly higher than rubber coated with silicone oil. Repetitive sliding friction testing showed that silicone oil treated samples had a longer lubricating lifetime than plasma treated samples. However, cyclic friction tests conducted with nitrile rubber o-rings yielded similar frictional behavior and lubricating lifetimes for silicone oil and plasma treatments. There was no correlation between chemical composition and the frictional and wear properties of the plasma films. Environmental scanning electron micrographs showed that the plasma films were brittle and tended to crack and flake off during wear testing.     

Study on microstructure and mechanical properties relationship of short fibers/rubber foam composites

Research on short fibers/rubber foam composites is rarely found in the literature. In this paper, microcellular rubber foams unfilled (MF), strengthened by pretreated short fibers (MFPS) and untreated short fibers (MFUS) are prepared, respectively. The microstructure and mechanical properties of the three composites have been studied via scanning electron microscope (SEM) and mechanical testing, respectively. The SEM results show that both pretreated and untreated short fibers disperse uniformly in the composites and in bidimensional orientation. Moreover, the pretreated short fibers have much better adhesion with the rubber matrix than untreated ones. The experimental results also indicate that the introduction of short fibers is mainly responsible for the great enhancement of most mechanical properties of the microcellular rubber foams, and the good interfacial adhesion of the short fibers with the matrix contributes to the more extensive improvement in the mechanical properties. It is also found that the reinforcement effect of short fibers to compressive modulus strongly depends on the density of microcellular rubber foams, the orientation of short fiber and the deformation ratio. The compressive modulus of microcellular rubber foams at the normalized density less than 0.70 and beyond 0.70 is predicted by the modified Simple Blending Model and the Halpin-Kerner Model, respectively. The theoretically predicted values are in good accordance with the experimental results.     

环氧化橡胶及其合金的研究与应用

综述了国内外环氧化橡胶及其合金的研究现状和应用趋势,重点介绍了环氧化天然橡胶、环氧化聚丁二烯、环氧化苯乙烯-丁二烯-苯乙烯三嵌段共聚物及其合金的优点,以及影响其物理机械性能的因素和环氧化橡胶的发展方向。     

New double negative and positive temperature coefficients of conductive EPDM rubber TiC ceramic composites

In this paper, we have successfully prepared ethylene-propylene-diene monomer (EPDM)/TiC composites as thermistors, with new double negative and positive temperature coefficients of conductivity (NTCC/PTCC). EPDM composites loaded with 50 phr HAF carbon black and different concentrations of TiC were prepared. This study focuses on the effect of TiC content on the vulcanization process, the network structure and the electrical and thermal properties of EPDM/TiC composites. The effect of TiC on the network structure was evaluated e.g. the curing process, the characteristic time constant during vulcanization, the volume fraction of rubber, gel fraction, interparticle distance between conductive particles, the extent of TiC reinforcement in the rubber matrix and molecular weight between cross-linking through experimental and affine-phantom models. The effects of TiC content on the percolation theory, electrical conductivity, conducting mechanism of conductivity, conducting hysteresis and I-V characteristics were also studied, as well as its TiC on the (NTCC/PTCC), thermoelectric power, dielectric constant and thermal conductivity. Stability and reproducibility of the thermal cycles for heating element applications was tested. Specific heat and the amount of heat transfer by radiation and convection as a function of TiC content was calculated using both the calorimetric technique and a theoretical model. It was proved that TiC improves the network structure, electrical and thermal properties of EPDM composites for practical applications.     

类人气动肌肉模型与实验研究

在理论分析和实验的基础上，建立了人工气动肌肉的数学模型．该模型中考虑了橡胶管弹性、类人气动肌肉壁厚、人工肌肉末端弧度、编织网线之间以及编织网和橡胶管之间的摩擦力对气动肌肉驱动特性的影响．设计实验系统对人工气动肌肉进行了等压实验、负载拉力恒定实验和等长实验，实验结果与改进后的模型仿真结果吻合较好．     

橡胶补强用酚醛树脂的研究

对橡胶补强用酚醛树脂的合成方法、反应原理、工艺条件、性能鉴定等予以较为详细的讨论。认为该类酚醛树脂是现代子午线轮胎和其他橡胶制品重要而理想的补强剂。     

高岭土机械力化学改性研究

利用物料在超细粉碎过程中的机械力效应,以振动磨为载体和工具,对用作橡胶补强剂的高岭土材料进行了一系列机械力化学改性实验,探讨了偶联剂种类、改性剂投入时间和持续作用时间等工艺参数对改性效果的影响,实验结果对同类的研究提供了借鉴依据.     

新型天然橡胶吸油树脂的研制及其性能研究

以天然橡胶生胶为单体．二乙烯苯为交联剂，过氧化蓉甲酰为引发剂，在甲苯溶液中交联聚合得到新型天然橡胶吸油树脂，并对其分子结构进行红外光谱表征。此外探讨了聚合反应条件对树脂吸油率和吸油速率的影响以及树脂的缓释性能。天然橡胶吸油树脂对甲苯的最大吸收率为25．0，对煤油的最大吸收率为26.6。