帽形加劲复杂卷边槽钢柱偏压性能试验研究

对共计18个简支试件进行偏心受压试验,分析并研究了未加劲、腹板中央帽形加劲、腹板和翼缘中央帽形加劲3种截面复杂卷边槽钢的极限承载力、失稳模式及变形特征等特性.结果表明:有效形心移动对偏心承压构件的承载能力有很大影响.在板件中央设置帽形加劲可以适当减小板件的宽厚比,显著提升受压构件的极限承载力及钢材利用率,但畸变屈曲在构件失稳模式中起控制作用.在同等条件下,板件中央帽形加劲偏压构件的承载效率提升了15%~70%.     

基于路用性能的石灰-钢渣稳定土试验分析

基于路用性能设计正交试验,研究了影响石灰-钢渣稳定土抗压强度的4种因素.结果表明,对于石灰-钢渣稳定土初期抗压强度,石灰含量影响最大,钢渣影响较小;但对于其后期抗压强度,钢渣掺量的影响明显增强,且钢渣粒径大小对后期强度增长速率的影响较大.试验结果对比发现,石灰-钢渣稳定土具有较高的无侧限抗压强度和加州承载比,满足《公路路基设计规范》(JTG D30-2015)和《公路路面基层施工技术细则》(JTG/T F20-2015)的要求,表明可以使用钢渣代替部分石灰或水泥应用于高速公路路床填料.     

计入孔隙结构影响的复层含油轴承润滑特性分析

基于Darcy定律和Kozeny-Carman孔隙方程,建立多孔质复层含油轴承的流体润滑模型,利用有限差分法数值模拟,分析复层结构和孔隙参数对含油轴承润滑性能的影响.得出结论如下:复层含油轴承润滑性能随轴承高度增大而变差,随孔隙率减小而变好,当总孔隙率一定时,较低的表层孔隙率有利于提高复层含油轴承润滑性能.因此设计复层含油轴承时,在保证一定孔隙含油量的前提下,应尽可能减小表层孔隙率.研究工作为复层含油轴承摩擦学性能分析与结构设计提供一定的理论基础.     

歪斜安装对组配轴承转子系统动力学特性影响

针对多联组配轴承歪斜安装情况,推导了一个轴承外圈发生绕竖直方向歪斜时滚动轴承的非线性支承力形式,并借助Timoshenko梁轴单元建立了主轴模型,利用打靶法和Floquet理论分析了歪斜对系统全局非线性稳定特性和振动特性的影响。通过与正常安装组配轴承转子系统对比发现:外圈歪斜后系统在大间隙时的低转速区域容易出现倍周期分叉,在高转速区域易表现为伪周期分叉;在小间隙工况时容易获得大范围的周期运动参数区域。同时,歪斜使得系统的一临界峰峰值右移且明显放大,从而导致系统在高转速区域的水平方向振动明显增大。研究结果表明,掌握且合理利用轴承歪斜后的非均匀间隙特性,有助于改善系统运行的动力特性。     

基于显式动力学的发动机转子中介轴承的仿真分析

为研究复杂工况下中介轴承的动力学特性，针对外圈支承于低压转子轴颈，内圈支承于高压转子轴颈支承形式的中介轴承的工作特点，应用LS-DYNA建立了中介圆柱滚子轴承动力学模型，开展动力学仿真。该模型以显式算法为基础，在充分考虑中介轴承转速、旋转方向、负载、接触及摩擦的条件下，基于动力学仿真模型，分析了中介轴承应力水平随内外圈旋转方向、内外圈转速及径向外载荷变化的规律。分析结果表明：在内外圈反向旋转以及外圈转速增加的情况下中介轴承的振动更为平稳，而在径向外载荷增大的情况下，中介轴承的振动更加剧烈。仿真结果验证了模型的正确性，为中介轴承故障诊断提供了有益参考。     

Numerical methods for theoretical analysis of foil bearing dynamics

The bearing under consideration is a self-acting, gas bearing with a flexibly supported foil. In order to conduct the theoretical analysis, three systems were identified: a rotor, a gas film and a flexible structure. Each of these elements has been mathematically analysed and analytical equations have been formulated. It was found, that the gas flow in the bearing can be described by the Reynolds equation, whereas a spring-damper model was selected for the structural analysis. The Reynolds equation is a differential equation the exact solution to which is unknown. The work describes the finite difference method in detail, where the partial derivatives in the Reynolds equation are replaced by a system of algebraic equations. In order to solve the resulting system, the Alternating Direction Implicit method (ADI) was used. Based on that and on the analysis of interactions between the three systems the equations have been computed. The accuracy of methods has been verified by means of series of numerical tests. Chosen results are described in this paper.     

应用高分子材料整治铁路桥梁支座病害

分析了铁路桥梁支座病害的成因,介绍了应用高分子材料整治桥梁支座病害的施工工艺和取得的效果.     

Effect of modified glass fiber on tribological performance of water-lubricated bearing

Glass fiber (GF) is becoming one of the most popular reinforcement materials used in many fields. However, it still has some disadvantages such as brittleness and poor wear resistance. In order to improve its tribological property, the GF was modified and use high-density polyethylene (HDPE) as the matrix material to verify it. In this work, friction tests of HDPE samples with seven different compositions of modified GF were carried out. Different working conditions were applied to determine the tribological properties and service life as used in water-lubricated bearings. Their friction coefficient, surface morphology, wear scar, wear quality and wear mechanism were investigated. The results showed that the modified GF could significantly improve the HDPE tribological properties. Moreover, the wear mechanism of pure HDPE was mainly adhesive wear and slight fatigue wear, and the composite material was mainly abrasive wear. The 30% GF composite material had the best wear resistance, its friction coefficient was reduced by 51.56% under 0.4 MPa and 500 r/min. The findings from this experiment will provide a new method for reducing friction and wear of water-lubricated bearings.     

计入船体变形影响的轴系动态校中研究

船体变形是影响船舶推进轴系校中质量的一个非常重要的动态因素.在研究船舶装载、波浪荷载及环境温度作用下船体变形计算方法的基础上,提出了一种轴承变位的计算方法,用以进行轴系动态校中研究.以76 000 t成品油轮为例,计算了极限装载状态下的重力分布和常遇较大海况时的波浪荷载,并分析了环境温度荷载分布.通过对整船有限元模型合...     

超精密气浮工件台误差建模

为了研究多种作用因素在高加速、大行程条件下对超精密微动台静态精度的影响,利用刚体运动学,通过综合工件台中的线性位置误差与角位置误差,建立了超精密气浮工件台的静态误差解析模型。利用该模型,结合有限元等方法定量分析了超精密气浮工件台中加速度、制造误差、结构柔性及气浮轴承刚度等普遍存在的误差因素同时作用时对系统最终精度的影响。通过分析,证明在高加速、大行程条件下,气浮轴承的角刚度不足是造成静态误差的主要因素。