阿姆河右岸生物礁滩储层的横波速度预测方法

为提高阿姆河右岸生物礁滩储层叠前弹性参数反演的精度和可靠性,采用岩石物理测试分析的纵、横波速度的关系式估算小孔隙度储层的横波速度,采用基于基质矿物等效体积模量反演方法、碳酸盐岩孔隙结构反演方法和Xu-White模型方法估算中、大孔隙度储层的横波速度。用该方法计算的横波速度结果与没有考虑该区孔隙结构的计算方法结果对比,精度明显提高,并且和实际测井的横波速度曲线也更加吻合。根据阿姆河右岸生物礁储层的特点,对储层孔隙结构分类采用不同的横波预测方法,更适合于该区的生物礁滩储层反演和油气预测。     

BIC实验的数值模拟研究

为研究低速撞击作用下炸药点火机理,采用非线性动力学LS-DYNA程序和Visco-SCRAM本构模型数值模拟弹道撞击室实验. 计算得到了5.35 m/s初始撞击条件下炸药发生点火反应,与文献中的实验结果比较吻合. 计算结果表明,炸药整体温升并不能导致其点火反应,而裂纹面摩擦生热形成热点能使炸药发生点火反应,计算结果可为低速撞击条件下炸药装药发生非冲击点火反应机理提供新的依据和支撑.      

Comparative study of bulk and partial digestion methods for airborne PM10-bound elements in a high mineral dust urban site in Constantine,Algeria

When high mineral loads in atmospheric particulate matter (PM) are present, particular attention should be paid to the selection of appropriate acidic digestion protocols for wet chemical analysis. We report on a comparative study of elemental recovery yields from five different pre-analytical acid digestion procedures for mineral-rich urban background PM₁₀ samples collected in the city of Constantine (Northeastern Algeria). Five reference materials (NIST 1633b, UPM 1648, NAT-7, SO-2 and SO-4) were also digested according to the same protocols. The selected acidic digestion/extraction procedures are widely used for PM chemical analysis and comprise P1 (HNO₃/HF/HCl), P2 (HCl/HNO₃), P3 (HCl/H₂O₂/HNO₃), P4 (HNO₃/HF/HClO₄) and P5 (HNO₃/H₂O₂); the latter assisted with microwave digestion. Elemental recovery yields were compared for major and trace elements typically determined in PM for source apportionment analysis and the results evidenced large differences. For most elements, the bulk extraction procedures (requiring the use of HF) allowed a full elemental recovery, particularly for elements that are associated with aluminium silicate species and oxides that are resistant to mild acid attack. In contrast, in the extraction protocols without HF low recovery yields were obtained for elements such as Al, Ti, Zr, Sc and other aluminium silicate-related elements in PM₁₀ samples with high mineral dust load. We highlight that the European standard digestion method EN-14902:2005 should be applied specifically for the metals for which this method was developed, but caution should be taken when the analysis of other elements in PM is required, especially in urban areas where road and vehicle wear dust is likely to be a major component of ambient PM. When using wet chemistry analysis for PM source apportionment studies, we strongly recommend HF bulk dissolution of samples to ensure the reliability of the geochemical information when coupled with an appropriate analytical tool.     

Individual and simultaneous determination of lead, cadmium, and zinc by anodic stripping voltammetry at a bismuth bulk electrode

A bismuth bulk electrode (BiBE) has been investigated as an alternative electrode for the anodic stripping voltammetric (ASV) analysis of Pb(II), Cd(II), and Zn(II). The BiBE, which is fabricated in-house, shows results comparable to those of similar analyses at other Bi-based electrodes. Metal accumulation is achieved by holding the electrode potential at −1.4 V (vs. Ag/AgCl) for 180 s followed by a square wave voltammetric stripping scan from −1.4 to −0.35 V. Calibration plots are obtained for all three metals, individually and simultaneously, in the10-100 μg L⁻¹ range, with a detection limit of 93, 54, and 396 ng L⁻¹ for Pb(II), Cd(II), Zn(II), respectively. A slight reduction in slope is observed for Cd(II) and Pb(II) when the three metals are calibrated simultaneously vs. individually. Comparing the sensitivities of the metals when calibrated individually vs. in a mixture reveals that Zn(II) is not affected by stripping in a mixture. However, Pb(II) and Cd(II) have decreasing sensitivities in a mixture. The optimized method has been successfully used to test contaminated river water by standard addition. The results demonstrate the ability of the BiBE as an alternative electrode material in heavy metal analysis.     

放电脉冲重频准分子激光器在不同应用领域的发展现状(英文)

研究了脉冲宽度为25～40 ns的放电脉冲XeCl准分子激光器的工作参数。结果显示,激光器产生的脉冲能量为0.2～0.7 J,重复频率为100 Hz,表明在泵浦功率为2.8～3.3 MW/cm3时,激光器实现了2.6%的激光效率和3.8%的本征效率。     

What we have learned from studies on chemical properties of amorphous alloys?

Amorphous alloys have many attractive characteristics including extremely high corrosion resistance if the sufficient amounts of corrosion-resistant elements are added. The superiority of amorphous alloys is based on the homogeneous single phase nature without any chemical and physical heterogeneities. Although there are processing limitations to avoid the formation of heterogeneous crystalline structure in addition to no welding technology without crystallization, the application of corrosion-resistant amorphous alloys is expected particularly to the very aggressive environments, where any conventional crystalline metallic materials cannot be used. Some amorphous bulk alloys showed zero corrosion mass loss due to spontaneous passivation even in 12 M HCl. Production of amorphous bulk alloys became possible for selected compositions. The homogeneous single phase nature is also effective to form useful catalysts with unique composition and structure. An example of catalysts is for carbon dioxide methanation useful for supply of renewable energy in the form of methane.     

Pressure–volume–temperature behavior of two polycyanurate networks

The pressure–volume–temperature (PVT) behavior was studied for two polycyanurate networks having different crosslink densities using a pressurizable dilatometer. The samples were studied at temperatures ranging from 60 to 180 °C and at pressures up to 170 MPa to yield PVT data in both rubbery and glassy states. The Tait equation is found to well describe the isobaric temperature scan and isothermal pressure scan data. The thermal expansion coefficients, instantaneous bulk moduli, and thermal pressure coefficients are extracted from the data and their dependence on crosslink density is examined. The time‐dependent viscoelastic bulk modulus (K(t)) is also calculated in the vicinity of the α‐relaxation from previously published pressure relaxation experimental data, and the strength and shape of the dispersion are found to be independent of crosslink density. The limiting bulk moduli depend strongly on temperature with those of the more loosely crosslinked sample being lower at a given temperature and pressure, although at T_g(P), the limiting moduli of the more loosely crosslinked sample are slightly higher than those of the more highly crosslinked sample. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

包覆状态下的大块Pb晶体的动力学过热

研究了非自由表面大块晶体Pb的过垫热，主要介绍通过有效的方法制得试样，然后，用DSC-7准确测量大块晶体Pb在不同加热速度条件下的过热度，从而得出大块晶体Pb能够产生动力学过热。