碱改性γ－Al_2O_3催化剂表面碱强度分布与COS水解活性的研究

用非水滴定法和Ｈａｍｍｅｔｔ系列指示剂测定了ＣＯＳ水解碱改性γ－Ａｌ_２Ｏ_３催化剂的表面碱强度分布．发现表面碱强度分布不均匀与表面能量分布不均匀相呼应．采用零点酸碱强度（Ｈ_（０，ｍａｘ））及碱中心区域分析法，Ｂｒｏｎｓｔｅｄ催化定律，进一步证实ＣＯＳ水解反应具有明显碱催化特征，较高活性催化剂的Ｈ_（０，ｍａｘ）一般为１０左右，对ＣＯＳ水解反应起主要作用的碱性中心的碱强度（Ｈ_０）为４．８≤Ｈ_０≤９．８．对碱金属氧化物改性后的γ－Ａｌ_２Ｏ_３催化剂，Ｂｒｏｎｓｔｅｄ规律在每个碱强度分区域内是适用的．     

Early-stage flocculation kinetics of polystyrene latex particles with polyelectrolytes studied in the standardized mixing: Contrast of excess and moderate polyelectrolyte dosage

Standardized mixing procedure was applied to the analysis of flocculation of polystyrene latex (PSL) particles with polyelectrolytes. After confirming the initial enhancement of flocculation rate in the very beginning followed by abrupt stop with excess dosage, attention was shifted to the system of moderate dosage. In the former, effects of ionic strength were further analyzed to find the consistency with adsorption isotherm. In the latter, flocculation started slowly in the beginning, sometime slower than salt-induced rapid coagulation, however, the rate gradually increases in the middle stage. Often, the increased rate exceeds that of salt-induced rapid coagulation. This behavior emerged more clearly in the case of lower ionic strength. This is the indication that the rate of relaxation of polymer on the colloidal surface is a function of surface coverage and ionic strength. The ultimate degree of flocculation is usually higher than that observed for excess dosage. The size distribution of flocs was also examined, however, no clear difference between different experimental conditions was confirmed for the same degree of flocculation.     

块状LaNi5基纳米合金的正电子湮灭研究

利用高温高压技术，在不同的压力和温度(-4．5GPa，-800℃)下将LaNi5基快淬合金粉直接压制成了块状纳米晶合金。X射线衍射分析表明，高压使其晶粒内部发生了明显的压致晶粒碎化，其平均晶粒尺寸在4．5GPa下从75．5nm降至24．6nm。利用正电子湮灭技术研究了这种晶粒碎化效应对纳米合金内部缺陷结构的影响。测试结果表明，在高温高压的作用下，由于界面上原子的迁移和弛豫加剧，导致晶界上尺寸较大的微孔隙缺陷逐渐转化为尺寸较小的自由体积缺陷，使得纳米合金的致密度逐渐增强，显微硬度逐渐升高，从而在高温高压下得到致密的块状纳米合金材料。     

电沉积羟基磷灰石/TiO2复合涂层

结合强度;电沉积羟基磷灰石/TiO2复合涂层     

Second Dissociation Constants of 4-[N-morpholino]butanesulfonic Acid and N-[2-hydroxyethyl]piperazine-N′-4-butanesulfonic Acid from 5 to 55°C

The values of the second dissociation constant, pK ₂, for the dissociation of the NH⁺ charge center of the zwitterionic buffer compounds 4-(N-morpholino)butanesulfonic acid (MOBS), and N-(2-hydroxyethyl)piperazine-N-4-butanesulfonic acid (HEPBS) have been determined from 5 to 55°C, including, 37°C at intervals of 5°C. The electromotive-force (emf) measurements have been made utilizing hydrogen electrodes and silver–silver chloride electrodes. The value of pK ₂ for MOBS was found to be 7.702 ± 0.0005, and 8.284 ± 0.0004 for HEPBS, at 25°C, respectively. The related thermodynamic quantities, G ^o, H ^o, S ^o, and C _p ^o for the dissociation processes of MOBS and HEPBS have been derived from the temperature coefficients of pK ₂. Both the MOBS and HEPBS buffer materials are useful as primary pH standards for the control of pH 7.3 to 8.6 in the region close to that of physiological fluids.     

Percolation in strongly correlated systems: The massless Gaussian field

We derive a number of new results for correlated nearest neighbor site percolation onZ ^d. We show in particular that in three dimensions the strongly correlated massless harmonic crystal, i.e., the Gaussian random field with mean zero and covariance –, has a nontrivial percolation behavior: sites on whichS _x h percolate if and only ifh _c . with0 _c < . This provides the first rigorous example of a percolation transition in a system with infinite susceptibility.     

羟丙基甲基纤维素作为水泥添加剂研究(四)

以萘磺酸甲醛缩合物为分散剂，水溶性羟丙基甲基纤维素衍生物为粘稠剂，研究了它们的混合物对混凝土材料的分散性与粘稠性及其它性能的影响，并探索了其作用机理。     

JD树脂刻蚀及涂层的XPS研究

ＪＤ光学树脂表面刻蚀过程的ＸＰＳ研究表明，引进树脂遥ＣＯＨ，Ｃ＝Ｏ，Ｃ－ＳＯ３Ｈ，ＣＯＯＨ等基因随刻蚀温度的提高或时间的延长而增加，对其相对含量进行了计算，固化后的耐磨涂层具有ＳｉＯ２结构，ＪＤ板材的最佳刻蚀条件为２０℃，２０ｍｉｎ。     

Potentiometric measurements of the first hydrolysis quotient of magnesium(II) to 250°C and 5 molal ionic strength (NaCl)

The first molal hydrolysis quotient, Q_1.1, of Mg²⁺ was measured potentiometrically from 1 to 250°C at ionic strengths of 0.11, 0.31, 1.01, and 5.0 mol-kg^-1 in an aqueous NaCl medium using a hydrogen-electrode, concentration cell. Only hydrolysis of the first four percent of the magnesium in solution could be followed before precipitation of brucite, Mg(OH)₂(cr), occurred. The log Q_1.1 values were fitted as a function of temperature and ionic strength using four adjustable parameters. The resulting constants are compared with the limited existing low temperature data. At infinite dilution and 25°C the following quantities are reported: logK _1.1 = -11.68±0.05, †H_so = 70.1±1.2 kJ-mol^-1, †S^o = 11±4 J-K^-1-mol^-1, and †C _p ^o = 0 J-K^-1-mor^-1. At each ionic strength, including the values extrapolated to infinite dilution, the heat capacity change for the hydrolysis reaction was zero,i.e., logQ _1.1 was found to be a linear function of the reciprocal temperature in Kelvin, at least over the measured range of l-250°C. The hydrolysis constants at infinite dilution were modeled to 550°C and two kbar pressure with a function incorporating solvent density using published results obtained at these extreme conditions.