Ni-SDC固体氧化物燃料电池阳极的合成和性质

采用柠檬酸-硝酸盐溶胶-凝胶低温自蔓延燃烧法制备氧化镍（NiO）粉末和Ce0.8Sm0.2O1.9（SDC）粉末，并将NiO与SDC按不同质量比和不同制备工艺制备了固体氧化物燃料电池（SOFC）的阳极前身。再用自组装的还原装置将其在820℃经2．5h还原后，采用四端子法测量其电导率值。分析了阳极片电导率与阳极片微结构、Ni的质量百分数、混合研磨时间及烧结温度之间的关系。结果显示，阳极片的电导率强烈依赖于镍含量和制备工艺。     

壳聚糖固体聚合物电池用膜

壳聚糖是甲壳素脱乙酰基的产物，具有良好的成膜性、生物相容性、环保以及价格低廉等特点。作为一种碱性高分子膜材料，近年来已成为聚电解质研究领域中的研究热点。本文综述了壳聚糖固体聚合物电池用膜的研究现状，其改性工艺主要包括共混、化学改性、质子酸掺杂、无机盐掺杂等方法，比较了各种工艺处理后壳聚糖固体聚合物电解质膜的性能差异，并就壳聚糖固体聚合物电解质膜中离子传导机理中有待解决的问题进行探讨，并提出了进一步改进壳聚糖固体聚合物电解质膜性能的研究思路。     

Effect of Ba and Bi doping on the synthesis and sintering of Ge-based apatite phases

Recently, high oxide ion conduction has been observed in the apatite-type systems La_9.33+x(Si/Ge)₆O_26+x/2, with conductivities approaching and even exceeding that of yttria-stabilized zirconia. The Ge-based phases have been reported to suffer from Ge loss and undergo irreversible structural changes on sintering at the high temperatures required to obtain dense pellets. In this paper we discuss doping studies (Ba, Bi for La) aimed at stabilizing the hexagonal apatite lattice to high temperature, and/or lowering the synthesis and sintering temperatures. The results show that doping with Ba helps to stabilize the hexagonal lattice at high temperatures, although Ge loss appears to still be a problem. Conductivity data show that, as previously reported for the Si-based systems, non-stoichiometry in the form of cation vacancies and/or oxygen excess is required to achieve high oxide ion conduction in these Ge-based systems. Neutron diffraction structural data for the fully stoichiometric phase La₈Ba₂Ge₆O₂₆ shows that the channel oxygen atoms show little anisotropy in their thermal displacement parameters, consistent with the low oxide ion conductivity of this phase. Bi doping is shown to lower the synthesis and sintering temperatures, although the presence of Bi means that these samples are not stable at high temperatures under reducing conditions.Presented at the OSSEP Workshop Ionic and Mixed Conductors: Methods and Processes, Aveiro, Portugal, April 10–12, 2003     

Nickel-cermet anode for fuel cells with the LSGM electrolyte

The effect of some technological parameters (firing temperature, thickness of an interphase layer made of solid electrolyte Ce_0.82Gd_0.18O_1.91 (GDC), the GDC electrolyte amount in nickel-cermet) on the electrochemical and electric properties of a nickel-cermet (Ni-GDC) anode intended for fuel cells with the La_0.88Sr_0.12Ga_0.82Mg_0.18O_2.85 (LSGM) electrolyte is studied. The polarization resistance of such an electrode is shown to hardly depend on the thickness of the interphase layer (4.5–23.5 μm) and the GDC electrolyte amount in nickel-cermet and to increase with the anode firing temperature. It is established that the contact resistance is concentrated in cells with the developed nickel-cermet electrode at the GDC/LSGM interface. At a temperature of 700°C the developed anodes may ensure a current density of 1 A cm^?2 at an overvoltage of less than 100 mV when using both moist hydrogen and a methane-oxygen mixture as the fuel.     

丹麦生物质发电的现状和研究发展趋势

丹麦是世界上利用秸秆生物质燃烧发电技术开发、运行最好的国家，其经验值得中国借鉴。根据作者在丹麦对生物质燃烧发电的研究经历，系统地介绍了丹麦在秸秆生物质发电的经验、遇到的问题及相应的研究和今后的发展方向。     

CuZnAl水滑石衍生催化剂上甲醇水蒸气重整制氢Ⅲ.合成水滑石用金属盐的影响

采用共沉淀法,用不同金属盐为Cu源和Zn源合成了一系列CuZnAl水滑石,以此为前体经600℃焙烧后制得相应催化剂.用硝酸盐和醋酸盐合成的水滑石结晶度高,其衍生催化剂比表面积大、Cu的分散性好且易于还原;而用硫酸盐和盐酸盐合成的水滑石结晶度差,其衍生催化剂比表面积小、Cu的分散性差且不易还原.反应评价结果显示,用硝酸盐和醋酸盐制得的催化剂活性高、反应稳定性好;而用硫酸盐和盐酸盐制得的催化剂由于低的Cu表面积以及S和Cl的毒化作用而几乎无催化活性.在醋酸盐制备的催化剂上,产物干气中CO的浓度明显较低,在250℃和WHSV=3.28 h-1的条件下约为0.03%~0.04%,仅为硝酸盐所制催化剂上CO浓度的1/5;在210℃和WHSV=0.5 h-1的条件下,该催化剂上甲醇几乎完全转化,同时CO浓度降至约0.005%.N2O滴定、CO2程序升温脱附和程序升温还原结果显示,用醋酸盐和硝酸盐制备的催化剂具有极相近的Cu表面积和表面碱性,但前者CuO的还原峰温较后者低近70℃,归因于ZnO与CuO间的强相互作用,这是催化剂具有良好选择性的可能原因.     

精制煤液化中油加氢裂化制取喷气燃料的研究

在实验室固定床反应装置上,选用Mo-Ni-P/Si-Al工业催化剂,对精煤液化中油进行了加氢裂化制取喷气燃料的实验。考察了反应温度、空速对芳烃加氢转化及产品馏分分布的影响。通过加氢裂化,降低了油品芳烃含量,提高了喷气燃料馏分的收率。在总压为15MPa,反应温度为350—360℃,空速为0.8—1.0h~(-1)条件下,获得了芳烃含量低于10w%的低结晶点的优质喷气燃料产品。并对煤液化中油制取的喷气燃料的组成和性质进行了分析和评价。     

新型柴油节能降污添加剂的研制

为改善柴油燃料的燃烧性能,充分利用有限的石油资源,通过对两种单剂的制备、筛选,研制了一种新型柴油节能降污表面修饰纳米添加剂 添加剂以0.01‰质量分数加入柴油中,能显著提高柴油的燃烧效率、减少残炭.     

Characterization of SiO2-P2O5-ZrO2 Sol-Gel/NAFION™ Composite Membranes

Composite membranes were prepared by (a) infiltrating NAFION with SiO₂-P₂O₅-ZrO₂ sol, and (b) recasting a film using NAFION solution containing SiO₂-P₂O₅-ZrO₂ sol. The membranes were characterized by Differential Thermal Analysis and ac-impedance spectroscopy as a function of relative humidity. The influences of the heat treatment (80°C–150°C) and cleaning on the electrical properties were investigated. The incorporation of SiO₂-P₂O₅-ZrO₂ gels into NAFION lead to improvements in its thermal stability and proton conductivity.     

Electrochemical characteristics of Ce0.8Gd0.2O1.9|La0.6Sr0.4CoO3-δ + Ce0.8Gd0.2O1.9 half-cell

The analysis of the medium temperature half-cell Ce_0.8Gd_0.2O_1.9|70 wt% La_0.6Sr_0.4CoO_3- (LSCO) + 30 wt % Ce_0.8Gd_0.2O_1.9 (CGO) has been made by electrochemical impedance, cyclic voltammetry and chronoamperometry. The shape of complex impedance plots depends on temperature and cathodic polarisation of the electrode. Nyquist (Z, Z-) plots were fitted by equivalent circuit taking into account the electrolyte properties (at very high frequencies), charge transfer process at grain boundaries (at high frequencies), and medium and low frequency O₂ reduction process at the cathode surface and inside the porous cathode material. Two different time constants have been obtained for the cathode process, i.e. for electroreduction of oxygen. It was found that the addition of CGO into the cathode material (LSCO) only somewhat decreases the surface catalytic activity but the noticeably higher low-frequency resistance (i.e. mainly diffusion-like mass transfer resistance R_D) values at lower temperatures have been calculated. It was found that the mainly bulk diffusion-limited process at T773 K deviates toward the kinetically mixed process (diffusion + charge transfer) with increasing temperature.