Wear resistance of reactive plasma sprayed and laser remelted TiB2-TiC0.3N0.7 based composite coatings against medium carbon steel

Wear resistance of reactive plasma sprayed TiB₂-TiC_0.3N_0.7 based composite coatings and the as-sprayed coating with laser surface treatment was investigated using plate-on-plate tests. Wear tests were performed at different normal loads and sliding speeds under dry sliding conditions in air. The surface morphologies of counterparts against as-sprayed and laser remelted coatings were investigated. The microstructure and chemical composition of wear debris and coatings were studied using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS), respectively. The results show that the wear resistance of the laser remelted coating is improved significantly due to their increased microhardness and reduced flaws. The primary wear mechanism of the remelted coating is oxidation wear and its minor wear mechanisms are grain abrasion and fatigue failure during the course of wear test. In contrast, the primary wear mechanism of the as-sprayed coating is grain abrasion at the low sliding speed (370 rpm) and fatigue failure at the high sliding speed (549 rpm). The oxidation wear mechanism is a minor contributor for the as-sprayed coating.     

A corrosion resistant cerium oxide based coating on aluminum alloy 2024 prepared by brush plating

Cerium oxide based coatings were prepared on AA2024 Al alloy by brush plating. The characteristic of this technology is that hydrogen peroxide, which usually causes the plating solution to be unstable, is not necessary in the plating electrolyte. The coating showed laminated structures and good adhesive strength with the substrate. X-ray diffraction and X-ray photoelectron spectroscopy analysis showed that the coatings were composed of Ce(III) and Ce(IV) oxides. The brush plated coatings on Al alloys improved corrosion resistance. The influence of plating parameters on structure and corrosion resistance of the cerium oxide based coating was studied.     

Characterization of coating probe with Ti-DLC for electrical scanning probe microscope

In electrical scanning probe microscope (ESPM) applications, the wear and conductivity of the probe are undoubtedly serious concerns since they affect the integrity of the measurements. This study investigates the characterization of Ti doped diamond-like-carbon (DLC) as coating material on a silicon cantilever for ESPM. We deposited a layer of Ti-DLC thin film on the surface of Si cantilever by magnetron sputtering. The morphology and composition of the Ti-DLC films were characterized by scanning electron microscopy and Raman spectroscopy, respectively. We also compared the wear resistance, electric conductivity and scanning image quality of the Ti-DLC-coated probes with those of commercially available conductive probes. The results showed that the electric conductivity and the scanning image quality of the Ti-DLC-coated probes were the same as the commercial conductive probes, while the wear resistance and service life was significantly better.     

Investigation of the voltage and time effects on the formation of hydroxyapatite-containing titania prepared by plasma electrolytic oxidation on Ti-6Al-4V alloy and its corrosion behavior

Producing titania and hydroxyapatite (HA) bioceramic coating on titanium alloys increases corrosion resistance and biocompatibility of these alloys. Plasma electrolytic oxidation (PEO) is one of the effective techniques for producing this type of coating. This method produces coatings with enough thickness and appropriate adhesion. In this study, titania and HA were directly produced on Ti-6Al-4V by applying PEO process in a Ca- and P-containing electrolyte by changing voltage and time parameters. Morphology and cross section, chemical composition and elements of coatings were investigated by scanning electron microscope, X-ray diffraction and energy dispersive spectroscopy, respectively. Corrosion behavior of the samples was also examined by potentiodynamic polarization and electrochemical impedance spectroscopy. The results indicated that the formation of HA phase with titania needs a minimum voltage below which HA is not formed. By increasing the operation time, the amount of the formed HA increased. Also, the sample coated at 500 V and 15 min showed the best corrosion behavior in Ringer's solution.     

Enhanced in vitro biocompatibility of ultrafine-grained biomedical NiTi alloy with microporous surface

Bulk ultrafine-grained Ni_50.8Ti_49.2 alloy (UFG-NiTi) was successfully fabricated by equal-channel angular pressing (ECAP) technique in the present study, and to further improve its surface biocompatibility, surface modification techniques including sandblasting, acid etching and alkali treatment were employed to produce either irregularly roughened surface or microporous surface or hierarchical porous surface with bioactivity. The effect of the above surface treatments on the surface roughness, wettability, corrosion behavior, ion release, apatite forming ability and cytocompatibility of UFG-NiTi alloy were systematically investigated with the coarse-grained NiTi alloy as control. The pitting corrosion potential (E_pit) was increased from 393 mV (SCE) to 704 mV (SCE) with sandblasting and further increased to 1539 mV (SCE) with following acid etching in HF/HNO₃ solution. All the above surface treatment increased the apatite forming ability of UFG-NiTi in varying degrees when soaked them in simulated body fluid (SBF). Meanwhile, both sandblasting and acid etching could promote the cytocompatibility for osteoblasts: sandblasting enhanced cell attachment and acid etching increased cell proliferation. The different corrosion behavior, apatite forming ability and cellular response of UFG-NiTi after different surface modifications are attributed to the topography and wettability of the resulting surface oxide layer.     

Preparation of a silicon micro-strip nuclear radiation detector by a two-step annealing process

The annealing process for boron implantation is a crucial step during large size nuclear radiation detector fabrication. It can reduce the lattice defects and the projection straggling. A two-step annealing process for boron implantation was developed instead of a one-step annealing process, and the reverse body resistance of a silicon micro-strip detector was significantly increased, which means that the performance of the detector was improved.     

The electronic transport properties in C60 molecular devices with different contact distances

By applying non-equilibrium Green?s functions in combination with the density-functional theory, we investigate the transport behavior of molecular devices composed by metal electrode-C₆₀ molecule-metal electrode. Our results show that the electronic transport properties are affected obviously by the different contact distances between the electrodes, and the tunneling current decreases approximately exponentially at a certain bias with the increasing of contact distances. The negative differential resistance is observed and the peak-to-valley ratio can be tuned by different contact distances. The mechanisms of the contact distance effect and the negative differential resistance behavior are proposed.     

A delay-dependent model with HIV drug resistance during therapy

The use of combination antiretroviral therapy has proven remarkably effective in controlling HIV disease progression and prolonging survival. However, the emergence of drug resistance can occur. It is necessary that we gain a greater understanding of the evolution of drug resistance. Here, we consider an HIV viral dynamical model with general form of target cell density, drug resistance and intracellular delay incorporating antiretroviral therapy. The model includes two strains: wild-type and drug-resistant. The basic reproductive ratio for each strain is obtained for the existence of steady states. Qualitative analysis of the model such as the well-posedness of the solutions and the equilibrium stability is provided. Global asymptotic stability of the disease-free and drug-resistant steady states is shown by constructing Lyapunov functions. Furthermore, sufficient conditions related to the properties of the target cell density are obtained for the local asymptotic stability of the positive steady state. Numerical simulations are conducted to study the impact of target cell density and intracellular delay focusing on the stability of the positive steady state. The occurrence of Hopf bifurcation of periodic solutions is shown to depend on the target cell density.     

仪表放大器中电阻变化率与噪声的关系

探讨电阻变化率对由3个运算放大器组成的仪表放大器输出端噪声的影响.把运算放大器噪声模型和电阻噪声模型代入仪表放大器电路,得到输出端噪声与电阻的关系式,通过列表分析,按不同的电阻比筛选出对输出端噪声影响显著的电阻.orCAD软件的仿真结果验证了分析是正确的.     

某信用联社综合营业楼结构设计

通过一个高层建筑的工程实例，介绍高层建筑设计中经常遇到的设计问题的解决方法．