Application of a solid‐phase microextraction fiber coated with a graphene oxide‐poly(dimethylsiloxane) composite for the extraction of triazoles from water

A solid‐phase microextraction fiber was prepared by mixing graphene oxide and hydroxyl‐terminated polydimethylsiloxane together and then coating the mixture on the surface of etched stainless‐steel wire by sol–gel technology. After aging by heating, the graphene oxide‐polydimethylsiloxane composite coated fiber was used for the direct solid phase microextraction of triazole fungicides from water samples. The properties of the graphene oxide‐polydimethylsiloxane coating were characterized by transmission electron microscopy and thermogravimetric analysis. And the chemical stability of the coating was tested as well. Several important experimental parameters that could influence the extraction efficiency such as desorption temperature and time, extraction temperature and time, sample pH and stirring rate, were investigated and optimized. Under the optimized conditions, the limits of detection were in the range from 0.01 to 0.03 μg/L. The results indicated that the homemade fiber had the advantages of good thermal and chemical stability and high extraction efficiency, which was successfully applied to the analysis of triazoles in water samples.     

Comparison of BOD optical fiber biosensors based on different microorganisms immobilized in ormosil matrixes

Fiber-optical microbial sensors for determination of biochemical oxygen demand (BOD) are described. Sensing films consisting of layers of an oxygen-sensitive fluorescent material and two different kinds of seawater microorganisms immobilized in poly(vinyl alcohol) sol–gel matrix were investigated. Tris(4,7-diphenyl-1,10-phenanthroline)ruthenium(II) perchlorate was used as the oxygen fluorescent quenching indicator. After preconditioning, the BOD biosensors could consistently perform well for up to one month. For films of domestic bacilli and films of sieved bacteria from seawater, the linear fluctuant coefficients (R ²) in the range of 4–200?mg/L were 0.9975 and 0.9783 when a glucose/glutamate BOD standard was applied. The relative error of standard deviations for the two microorganism-immobilized BOD sensing films were within 4%?and 2%?of the mean value, respectively. The effects of temperature, pH and sodium chloride concentration on the two microbial films were also studied. For low biochemical oxygen demand, a film of sieved bacteria from seawater had superior sensitivity and is expected to be developed further.     

锂电池阴极材料Li(Co_xAl_(1-x))O_2的溶胶-凝胶法合成及表征

采用溶胶 -凝胶方法合成了锂二次电池阴极材料 Li( Cox Al1 - x) O2 ,并采用 XRD方法分析了材料的相变过程、烧结时间对材料合成的影响及不同 Al/Co比掺杂对材料相变的影响 ,并进行了结构表征 .研究表明 ,材料结构随 Al固溶度的增大及温度的升高呈现出 a轴缩短 ,c轴伸长的趋势 .材料晶相稳定温度在60 0～ 90 0℃之间 ,烧结时间在 3 h以上     

A novel strategy to increase performance of solid‐phase microextraction fibers: Electrodeposition of sol‐gel films on highly porous substrate

In the present work, the effect of substrate porosity for preparation of solid‐phase microextraction (SPME) fibers was investigated. The fibers were prepared by electrodeposition of sol‐gel coatings using negative potentials on porous Cu wire and compared with previous reported technique for preparation of SPME fibers using positive potentials on smooth gold wire. Porous substrate was prepared by electrodeposition of a thin layer of Cu on a Cu wire. The extraction capability of prepared fibers was evaluated through extraction of some aromatic hydrocarbons from the headspace of aqueous samples. The effect of substrate porosity and some operating parameters on extraction efficiency was optimized. The results showed that extraction efficiency of SPME fibers highly depends on porosity of the substrate. The LOD ranged from 0.005 to 0.010 ng/mL and repeatability at the 1 ng/mL was below 12%. Electrodeposited films were characterized for their surface morphology and thermal stability using SEM and thermogravimetric analysis, respectively. SEM analysis revealed formation of porous substrate and subsequently porous coating on the wire surface and thermogravimetric analysis showed high thermal stability of the prepared fiber.     

溶胶-凝胶法合成超细Li_(2 x)RE_xSi_(1-x)O_3及其离子导电性

用溶胶 凝胶法合成了Li2 xRExSi1 -xO3(RE =Pr ,Nd ,Sm ,Gd ;x =0～ 0 15 ) ,用DTA TG ,XRD ,TEM及交流阻抗等技术对样品的结构、形貌、粒径及离子导电性等进行了观察和测试。其固溶体形成范围是 0 相似文献   

Application of sol–gel TiO2 film for an extended-gate H+ ion-sensitive field-effect transistor

In this study, a sol–gel TiO₂ thin film has been spin-coated on a commercial ITO glass substrate as the extended-gate field effect transistor (EGFET) for hydrogen ion sensing. The as-deposited films are further annealed at various temperatures (T_a) under ambient atmosphere. It is found that the bi-layer structure of TiO₂/ITO EGFET exhibits good linear sensitivity from pH 1 to 11. Anatase TiO₂ appeared as early as T_a = 200 °C and a brookite (121) diffraction evolved at T_a = 500 °C. No prominent influence on the surface fine structures could be found at higher T_a. Due to the reduction or disappearance of the surface hydroxyl groups on TiO₂, the sensitivities of the TiO₂/ITO pH-EGFET device are rapidly reduced. However, the influence of the conductivity decay for ITO substrates annealed at high T_a could not be excluded. A maximum sensitivity 61.44 mV/pH is achieved as T_a = 300 °C.The bi-layer structure of TiO₂/ITO exhibits better long-term stability than the traditional ITO sensing membranes. In addition, the asymmetric hysteresis is more significant in alkaline buffer solutions, which could be explained by a site-binding model because the diffusion of H⁺ ions into the buried sites of the sensing film is more rapid than that of OH⁻ ions.     

Multiferroicity in La1/2Nd1/2FeO3 nanoparticles

Nano-sized La_1/2Nd_1/2FeO₃ (LNF) powder is synthesized by the sol–gel citrate method. The Rietveld refinement of the X-ray diffraction profile of the sample at room temperature (303 K) shows the orthorhombic phase with Pbnm symmetry. The particle size is obtained by transmission electron microscope. The antiferromagnetic nature of the sample is explained using zero field cooled and field cooled magnetisation and the corresponding hysteresis loop. A signature of weak ferromagnetic phase is observed in LNF at low temperature which is explained on the basis of spin glass like behaviour of surface spins. The dielectric relaxation of the sample has been investigated using impedance spectroscopy in the frequency range from 42 Hz to 1 MHz and in the temperature range from 303 K to 513 K. The Cole–Cole model is used to analyse the dielectric relaxation of LNF. The frequency dependent conductivity spectra follow the power law. The magneto capacitance measurement of the sample confirms its multiferroic behaviour.     

Pure CuCr2O4 nanoparticles: Synthesis,characterization and their morphological and size effects on the catalytic thermal decomposition of ammonium perchlorate

In the present paper a pure phase of the copper chromite spinel nanoparticles (CuCr₂O₄ SNPs) were synthesized via the sol–gel route using citric acid as a complexing agent. Then, the CuCr₂O₄ SNPs has been characterized by field emission scanning electron microscope (FE-SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). In the next step, with the addition of Cu–Cr–O nanoparticles (NPs), the effects of different parameters such as Cu–Cr–O particle size and the Cu/Cr molar ratios on the thermal behavior of Cu–Cr–O NPs + AP (ammonium perchlorate) mixtures were investigated. As such, the catalytic effect of the Cu–Cr–O NPs for thermal decomposition of AP was evaluated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA/DSC results showed that the samples with different morphologies exhibited different catalytic activity in different stages of thermal decomposition of AP. Also, in the presence of Cu–Cr–O nanocatalysts, all of the exothermic peaks of AP shifted to a lower temperature, indicating the thermal decomposition of AP was enhanced. Moreover, the heat released (ΔH) in the presence of Cu–Cr–O nanocatalysts was increased to 1490 J g⁻¹.     

Synthesis and electrochemical characteristics of xLi2MnO3–(1−x)Li(Mn0.375Ni0.375Co0.25)O2 (0.0 ≤ x ≤ 1.0) thin film cathode for lithium rechargeable micro batteries

We have compared the structure, microstructure, and electrochemical characteristics of xLi₂MnO₃–(1−x)Li(Mn_0.375Ni_0.375Co_0.25)O₂ (0.0 ≤ x ≤ 1.0) thin films with their bulk cathode laminate counterparts of identical compositions. Pure Li(Mn_0.375Ni_0.375Co_0.25)O₂ as well as the synthesized composite films partially transform into cubic spinel structure during charge–discharge cycling. In contrast, such layered to spinel phase transformation has only been identified in bulk cathode laminates with x ≥ 0.75. At a current density 0.05 mAcm⁻², the discharge capacity of Li(Mn_0.375Ni_0.375Co_0.25)O₂ thin film was measured to be ∼60 μAhcm⁻². The discharge capacity (∼217 μAhcm⁻²) was markedly improved in x∼0.5 composite thin film. The capacity retention after 20 charge discharge cycles are improved in composite films; however, their capacity fading could not be eliminated completely.