溶胶-凝胶法合成有机/无机杂化材料进展——1.组分间以化学键作用的有机/无机杂化材料

介绍了溶胶－凝胶法（Sol-gel process)制备组分间以化学键作用的有机／无机杂化材料的基本情况,根据合成方法进行分类,并指出其发展趋势。     

Ce1-xGdxO2-x/2的溶胶-凝胶法合成及其性质

利用溶胶-凝胶法合成了Ce₁-xGdxO_2-x/2(x=0.1～0.6)系列固体电解质,系统地研究了其结构、热膨胀系数和导电性.XRD结果表明,160℃即完全形成立方萤石结构.由于溶胶-凝胶法合成的物质粒度均匀,颗粒小,故在较低温度(1300℃)时即可形成高致密样品,此温度明显低于传统的高温固相法烧结温度(1600～1650℃).高温X射线衍射测得Ce_0.8Gd_0.2O_1.9的热膨胀系数为8.125×10^-6K₁.阻抗谱表明,溶胶-凝胶法合成可减少或消除固体电解质的晶界电阻,600℃时Ce_0.8Gd_0.2O_1.9的电导率为5.26×10^-3S/cm,活化能E_a=0.82eV.     

块状TiO2气凝胶的制备及其表征

随着以溶胶-凝胶法和超临界干燥技术为基础的气凝胶制备方法的逐步完善,已不断制备出多种气凝胶[1～3].由于TiO2具有半导体特性,它常被作为光催化剂而受到重视,但是TiO2气凝胶的结构强度远比SiO2气凝胶小,在制备过程中极易碎裂粉化,所以至今未见制备块状TiO2气凝胶的报道.Dagan等[4]曾用异钛酸丁酯为母体制得TiO2气凝胶,并发现水杨酸在TiO2气凝胶存在下的光解速率是一般TiO2粉末的10倍,但获得的仅为TiO2气凝胶粉末.张敬畅等[5]以无机盐为原料,采用溶胶-凝胶法结合超临界干燥技术制备了纳米级TiO2气凝胶,也未能得到块状TiO2气凝胶材料. 本文报道以正钛酸丁酯为原料制备块状TiO2气凝胶的方法,并用TEM,SEM,XRD和IR等手段对所获得的气凝胶进行了结构表征.     

溶胶-凝胶法制备壳聚糖/SiO2杂化材料

以正丁酐（Butyric anhydride)、壳聚糖(Chitosan）、甲基丙烯酰氧基丙基三甲氧基硅烷（MPTMS）、正硅酸乙酯（TEOS）为原料,采用迈克尔加成反应合成了丁酰壳聚糖-MPTMS,配合酸催化sol-gel过程,制备了透明的壳聚糖/SiO2杂化材料,FTIR表征了杂化材料的结构。TGA,SEM以及力学性能测试结果表明,杂化材料的成型工艺对材料的表面形貌、热分解温度以及力学性能的影响显著。     

Decomposition of methane over alumina supported Fe and Ni–Fe bimetallic catalyst: Effect of preparation procedure and calcination temperature

Catalytic decomposition of methane has been studied extensively as the production of hydrogen and formation of carbon nanotube is proven crucial from the scientific and technological point of view. In that context, variation of catalyst preparation procedure, calcination temperature and use of promoters could significantly alter the methane conversion, hydrogen yield and morphology of carbon nanotubes formed after the reaction. In this work, Ni promoted and unpromoted Fe/Al₂O₃ catalysts have been prepared by impregnation, sol–gel and co-precipitation method with calcination at two different temperatures. The catalysts were characterized by X-ray diffraction (XRD), N₂ physisorption, temperature programmed reduction (TPR) and thermogravimetric analysis (TGA) techniques. The catalytic activity was tested for methane decomposition reaction. The catalytic activity was high when calcined at 500 °C temperature irrespective of the preparation method. However while calcined at high temperature the catalyst prepared by impregnation method showed a high activity. It is found from XRD and TPR characterization that disordered iron oxides supported on alumina play an important role for dissociative chemisorptions of methane generating molecular hydrogen. The transmission electron microscope technique results of the spent catalysts showed the formation of carbon nanotube which is having length of 32–34 nm. The Fe nanoparticles are present on the tip of the carbon nanotube and nanotube grows by contraction–elongation mechanism. Among three different methodologies impregnation method was more effective to generate adequate active sites in the catalyst surface. The Ni promotion enhances the reducibility of Fe/Al₂O₃ oxides showing a higher catalytic activity. The catalyst is stable up to six hours on stream as observed in the activity results.     

磷钼酸和钛硅纳米复合氧化物构筑高活性氧化脱硫催化剂

采用溶胶凝胶法合成了钛硅纳米复合氧化物(TiO₂-SiO₂),并以其为载体用原位合成技术或浸渍法负载Keggin结构磷钼酸(HPMo)制备了复合催化剂,使用扫描电子显微镜(SEM)、傅里叶红外光谱仪(FT-IR)、紫外可见光谱仪(UV-Vis)、X射线衍射光谱(XRD)和比表面分析仪(BET)等测试手段对催化剂的结构进行表征。 结果表明,采用原位法合成的催化剂为纳米粒子,纳米晶骨架内存在微孔和介孔共存的孔道结构。 原位合成技术或浸渍法制备的催化剂中HPMo保持Keggin骨架结构。以模拟油品(二苯并噻吩、苯并噻吩或噻吩的正辛烷溶液)的氧化脱硫为探针反应,在选定的条件下:硫含量为200.0 g/g的正辛烷溶液和无水乙醇各10.0 mL,反应温度60 ℃,催化剂质量0.15 g,n(H₂O₂)∶n(S)=5∶1,二苯并噻吩的脱除率高于96.0%,产物中硫含量低于10.0 μg/g。 在相同的实验条件下,受电子云密度的影响,脱硫由易到难的顺序为二苯并噻吩>苯并噻吩>噻吩。 催化剂循环使用4次后活性未见明显降低,是一类绿色的模型有机硫化物氧化脱除工艺用催化剂。     

The Ionic Conductivity of Solid Electrolytes for Li4+xMxSi1–xO4‐yLi2O (M=Al,B) Systems

The Li_4+xM_xSi_4+xO₄‐yLi₂O (M=Al, B; x = 0 to 0.6, y = 0 to 0.5) ion conductors were prepared by the Sol‐Gel method and examined in detail. The powder and sintered samples were characterized by DTA‐TG, XRD, SEM, and AC impedance techniques. The experimental results show that the conductivity and sinterability in creased with the amount of excess lithium oxide in the silicate. The Li₂O phase acts as a flux to accelerate the sintering process and to obtain high conductivity of grain boundaries. The particle size of the sintered pellets is about 0.25 μm. The maximum conductivity at 200 °C is 5.40 × 10^?3s cm^?1 for Li_4.4Al_0.4 Si_0.6O₄‐0.3Li₂O.     

MoO3/SiO2催化剂的异丁烷选择氧化反应性能

分别采用浸渍法和溶胶－凝胶法制备了MoO3/SiO2催化剂，用XRD，TPR，IR，TPD和活性评价等手段对催化剂的影响，晶格氧活泼性，化学吸附性能和异丁烷选择氧化反应性能进行了研究。结果表明，催化剂表面由Lewis碱位Mo=M,Mo-O-Mo中的晶格氧和Lewis酸位Mo^6 构成，在MoO3/SiO2催化剂上，异丁烷主要通过甲基的H双位吸附在表面的Lewis碱位Mo=O上；在常压条件下，异丁烷选择氧化产物主要为异丁烷，甲基丙烯醛和甲基丙烯酸，其中深度氧化产物CO2主要由吸附的异丁烯继续反应生成；采用溶胶－凝胶法制备的MoO3/SiO2催化剂，可得到较高的异丁烷转化率和含氧有机物选择性。     

Development of new solid-phase microextraction fibers by sol-gel technology for the determination of organophosphorus pesticide multiresidues in food

Allyloxy bisbenzo 16-crown-5 trimethoxysilane was first used as precursor to prepare the sol-gel-derived bisbenzo crown ether/hydroxyl-terminated silicone oil (OH-TSO) SPME coating. The coating procedure involving sol solution composition and conditioning process was presented. Compared with commercial SPME stationary phases, the new coatings showed higher extraction efficiency and therefore could provide higher sensitivity for organphosphorous pesticides (OPs). Limits of detection (LODs) were in the range of 0.003-1.0 ng/g for these OPs in food samples (honey, juice, orange and pakchoi). The optimal extraction conditions of the new coatings to OPs in these samples were investigated by adjusting extraction time, salt addition, extraction temperature, and dilution ratios of samples with distilled water by using SPME coupled with gas chromatography (GC)-flame photometric detection (FPD). The method was applied to determine the concentrations of OPs in real samples.     

Preparation of a sulfonated fused-silica capillary and its application in capillary electrophoresis and electrochromatography

In the present paper, two new methods, sol-gel and chemical bonding methods, were proposed for preparation of sulfonated fused-silica capillaries. In the sol-gel method, a fused-silica capillary was coated with the sol solution obtained by hydrolysis of 3-mercaptopropyltrimethoxysilane (MPTS) and tetramethoxysilane, and followed by age; while in the chemical bonding method, a capillary was chemically bonded directly with MPTS. Then, both the resulting capillaries were oxidized with an aqueous solution of hydrogen peroxide solution (H2O2) (30%, m/m) to obtain the sulfonated capillaries. The electroosmotic flow (EOF) for the sulfonated capillaries was found to remain almost constant within the studied pH range, and greater than that of the uncoated capillary. However, the coating efficiency of the capillary prepared by chemical bonding method was higher than that by sol-gel method, by comparing their magnitude of the EOF, the degree of disguise of the silanol and reproducibility of preparation procedure. The effects of the electrolyte's concentration and the content of methanol (MeOH) on the EOF were also studied. Especially, the study of the apparent pH (pH*) on the EOF in a water-MeOH system was reported. Finally, capillary electrophoretic separation of seven organic acids was achieved within 6.5 min under optimal condition using the chemically bonded sulfonated capillary. Moreover, separation of four alkaloids on the sulfonated capillary was compared with that on uncoated capillary in different conditions. Ion-exchange mechanism was found to play a key role for separation of these four basic analytes on the sulfonated capillary.