On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

液压支架压力变送器的电路设计

分析了液压支架的压力特性并提出对压力变送器的技术要求，阐述了压力传感器的选择和外围电路的设计，对压力变送器的信号调理电路进行了仿真分析。     

An Efficient Numerical Model for Planar Spiral Inductor On-Chip

In this paper, a very useful numerical technique has been developed for analyzing the transient characteristics of a planar-spiral inductor on-chip. A locally conformal technique and an alternating-direction implicit scheme are applied to the finite-difference time-domain method. A formulation for solving three dimensional Maxwell’s equations is proposed. Using the proposed method, various parameters of the planar-spiral inductors have been analyzed and an equivalent circuit, which includes frequency-independent circuit elements, has been introduced. Highly computational efficiency is implemented. Numerical results show excellent agreement with the measured data over a wide frequency range.     

乌桕类可可脂结晶过程中表现体积变化

为了解乌桕类可可脂(CTCBE)缓冷结晶横向胀罐爆裂原因，研究CTCBE结晶过程中的膨胀特性，采用流体静力法测试了不同等温结晶条件下CTCBE结晶形成的表观密度和表观体积及其横纵向膨胀状况。结果表明，CTCBE缓冷结晶后形成外部和中部两个晶区。在5-25℃的各等温结晶范围内，当结晶温度增加时，外部结晶区域减小、表观密度变化不大；中部结晶区域增大、表观密度明显减小，CTCBE的表观体积、横向、纵向膨胀率均增大，膨胀横向大于纵向。进一步表明CTCBE在自然缓冷固化的表观体积根本上由其结晶温度决定。为有效防止横向胀罐，自然缓冷固化温度应低于10℃。     

苯在Ru-Zn/Ru（0001）合金表面上的吸附——密度泛函研究

为了理解苯在Ru-Zn合金催化剂上的部分加氢催化机理,采用密度泛函方法对苯在Ru-Zn/Ru（0001）面上的吸附进行理论研究。计算结果表明,当苯的碳原子或者共轭双键直接位于表面Zn原子的atop位时,其吸附热较Ru（0001）面上的类似吸附状态下降约60%.Zn原子与苯环C原子之间的排斥作用导致苯环的成键轨道与表面Ru原子的价层轨道之间的空间对称性下降,从而不利于苯与合金表面的键合。当吸附位离开Zn原子时,邻近Zn原子对于苯的吸附基本没有影响。     

Reversible nonlinear conduction in high‐density polyethylene/acetylene carbon black composites at various ambient temperatures

The reversible nonlinear conduction (RNC) in of high‐density polyethylene/acetylene carbon black composites with different degrees of crosslinking was studied above room temperature and below the melting point of high‐density polyethylene (HDPE). The experimental current density‐electric field strength curves can be overlapped onto a master curve, suggesting that the microscopic mechanisms for the appearance of RNC exist regardless of the ambient temperature and the crosslinking degree of the HDPE matrix. The relationship between the crossover current density and the linear conductivity can be explained in the framework of the dynamic random‐resistor‐network model. According to these results, two electron‐tunneling models are suggested to interpret the microscopic conduction behavior. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1212–1217, 2004     

Desorption behavior of a surfactant in a linear low‐density polyethylene blend at elevated temperatures

The desorption behavior of a surfactant in a linear low‐density polyethylene (LLDPE) blend at elevated temperatures of 50, 70, and 80 °C was studied with Fourier transform infrared spectroscopy. The composition of the LLDPE blend was 70:30 LLDPE/low‐density polyethylene. Three different specimens (II, III, and IV) were prepared with various compositions of a small molecular penetrant, sorbitan palmitate (SPAN‐40), and a migration controller, poly(ethylene acrylic acid) (EAA), in the LLDPE blend. The calculated diffusion coefficient (D) of SPAN‐40 in specimens II, III, and IV, between 50 and 80 °C, varied from 1.74 × 10^?11 to 6.79 × 10^?11 cm²/s, from 1.10 × 10^?11 to 5.75 × 10^?11 cm²/s, and from 0.58 × 10^?11 to 4.75 × 10^?11 cm²/s, respectively. In addition, the calculated activation energies (E_D) of specimens II, III, and IV, from the plotting of ln D versus 1/T between 50 and 80 °C, were 42.9, 52.7, and 65.6 kJ/mol, respectively. These values were different from those obtained between 25 and 50 °C and were believed to have been influenced by the interference of Tinuvin (a UV stabilizer) at elevated temperatures higher than 50 °C. Although the desorption rate of SPAN‐40 increased with the temperature and decreased with the EAA content, the observed spectral behavior did not depend on the temperature and time. For all specimens stored over 50 °C, the peak at 1739 cm^?1 decreased in a few days and subsequently increased with a peak shift toward 1730 cm^?1. This arose from the carbonyl stretching vibration of Tinuvin, possibly because of oxidation or degradation at elevated temperatures. In addition, the incorporation of EAA into the LLDPE blend suppressed the desorption rate of SPAN‐40 and retarded the appearance of the 1730 cm^?1 peak. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1114–1126, 2004     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

强流四脉冲电子束源实验研究

 为了进行强流多电子束源研究，对现有2MeV LIA 注入器进行了四脉冲改造，二极管脉冲电压约500kV。实验研究了天鹅绒阴极在四脉冲条件下的发射能力、传导电流负载效应以及阴极等离子体运动对阴极电子发射和束能量的影响。利用空间电荷限制流模型推算出阴极等离子体膨胀速率在1 ~4cm/μs之间。     

静电加速管中强流空间电荷效应的研究

 对一种工业用大功率电子加速器(450kW)的加速管中的空间电荷效应作了5点假设，建立了物理模型。对模型的束内外径向电位分布、空间电荷对轴上电位的影响，以及空间电荷力对束流传输的影响等进行了理论分析，得到了束内径向电位分布。结果表明：束流内部径向电位沿径向均呈抛物线变化，并在轴上达到最小值；而空间电荷产生的束内电场与半径呈线性变化；空间电荷不仅会引起轴上电位的跌落，而且对束流有发散作用，特别是在电子速度较低时更为明显。在考虑了空间电荷效应后，强流静电加速管的电场设计关键在加速管的前端，与弱流加速管相比，强流加速管的电场变化要大得多。