Emanation Thermal Analysis of SiC Based Materials

Results of emanation thermal analysis (ETA) characterizing microstructure changes of SiC based materials during heat treatment in argon are demonstrated. This method made it possible to reveal fine changes of the texture of SiC nano-sized powders, SiC micro-sized powders and SiC whiskers under in situconditions of the heating. ETA curves can serve as fingerprints of the respective samples.This revised version was published online in November 2005 with corrections to the Cover Date.     

Y2O3:Eu3+纳米线阵列的制备与表征

Y2O3:Eu3+红色荧光粉由于色纯度高、化学性质稳定和量子效率接近100%而广泛用于荧光灯和投影电视等方面.近年来,Y2O3:Eu3+的大量研究工作主要集中于纳米粉末的制备方法及其与体相材料不同的发光特性[1～3].最近,有关Y2O3:Eu3+及其稀土化合物的纳米管、纳米线和纳米带一维材料的制备成为研究热点.Wu Changfeng等[4,5]利用表面活性剂合成了Y2O3 : Eu3+纳米管.激光格位选择激发测试结果表明,Eu3+在纳米管中占据3个不同的格位,其611 nm处的红色发光峰出现了宽化.He Yu等[6]采用水热法及退火处理制备出了Y2O3:Eu3+纳米带,发现Eu3+的发射峰不仅宽化,而且出现了625 nm的新峰.Li Yadong等[7～9]采用水热法制备了稀土氧化物、硫氧化物和氢氧化物等的纳米线和纳米管,并探索了其形成机理,同时发现Y2O3S : yb3+,Er3+具有上转换的性质.     

聚甲醛自然老化的SEM研究

对户外曝晒3～36个月的聚甲醛(POM)老化形态进行了研究,讨论了老化层厚度,裂纹宽度、裂纹深度及断口形态与老化时间的关系。结果表明:POM的老化导致了材料内部结构由韧性变成脆性而几乎完全丧失物理机械性能。     

Visible Up-Conversion Luminescence in Ho3+: BaTiO3 Nano-Crystals Prepared by Sol Gel Technique

Visible up-conversion emissions at (435, 545, 580, 675 and 690 nm) and (437, 547 575 and 675 nm) have been observed from the sol-gel derived nano-crystalline Ho³⁺: BaTiO₃ powders and thin films respectively, under 808 nm laser diode excitation emissions. Combined with the energy level structure of Ho³⁺ ions and the kinetics of the visible emissions, the up-conversion mechanism has been analyzed and explained. The blue, green and red emissions of both samples has been attributed to the ground state-directed transition from (⁵F₁), (⁵S₂) and (⁵F₅), which are populated through excited state absorption (ESA) for 808 nm excitation. Nano-structure pure barium titanate and doped with different concentrations of Ho³⁺ ions in the from of powder and thin film have been prepared by sol-gel technique, using barium acetate (Ba(Ac)₂), and titanium butoxide (Ti(C₄H₉O)₄), as precursors. The thin films were prepared by sol-gel spin coating method. The as-grown thin films and powders were found to be amorphous, which crystallized to the tetragonal phase after heating at 750°C in air for 30 minutes. The crystallite sizes of the thin film and powder both doped with 4% Ho³⁺ ions was found to be equal to 11 and 16 nm, respectvely.     

Thermal Analysis of Acrylonitrile Polymerization and Cyclization in the Presence of N,N-Dimethylformamide

This paper examines the polymerization of acrylonitrile to poly(acrylonitrile)(PAN), and its cyclization, in bulk form and using N,N-dimethylformamide (DMF) as solvent in which both monomer and polymer are soluble. Thermal analysis of the resultant products after polymerization has been performed by DSC and pyrolysis gas chromatography/mass spectrometry (Py-GC/MS). Scanning electron microscopy has been used to study the morphology of the resultant products and after thermal treatments. The DSC thermal curve of PAN-DMF sample is quite different from the PAN bulk sample, showing a single sharp exothermic peak associated with nitrile group polymerization (cyclization) of PAN at lower temperature (240°C) than that of bulk PAN sample (314°C). Cyclization of PAN was confirmed by IR spectroscopy. It was found that the amide molecules are difficult to eliminate completely in the product obtained after the polymerization reaction, even after prolonged heating at 110°C, and remain occluded. The formation of a complex by dipolar bonding is also possible and it is discussed. It is concluded that the amount of heat evolved as well as the temperature interval over which it is released are influenced by the chemical processing of PAN when using DMF as solvent of both monomer and polymer. Pyrolysis of these PAN samples revealed the release of occluded molecules of DMF, and several compounds containing nitrogen produced from the thermal degradation processes. All these results are interesting to know the chemical processing of carbon fibres and activated carbon fibres from PAN modified precursors.This revised version was published online in November 2005 with corrections to the Cover Date.     

Chemometric classification of gunshot residues based on energy dispersive X-ray microanalysis and inductively coupled plasma analysis with mass-spectrometric detection

A gunshot residue sample that was collected from an object or a suspected person is automatically searched for gunshot residue relevant particles. Particle data (such as size, morphology, position on the sample for manual relocation, etc.) as well as the corresponding X-ray spectra and images are stored. According to these data, particles are classified by the analysis-software into different groups: ‘gunshot residue characteristic’, ‘consistent with gunshot residue’ and environmental particles, respectively. Potential gunshot residue particles are manually checked and – if necessary – confirmed by the operating forensic scientist.     

A comparative study between inductively and capacitively coupled plasma deposited polystyrene films: chemical and morphological characterizations

Thin polystyrene films were deposited on stainless steel substrates by capacitively and inductively coupled radio frequency glow discharge plasma, in order to compare their chemical and morphological properties. The films were characterized by Fourier‐transform infrared spectroscopy (FTIR), X‐Ray photoelectron spectroscopy (XPS), time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS), atomic force microscopy (AFM) and scanning electron microscope (SEM). Wettability properties were also determined by contact angle measurements. Ageing effect was studied by analysing films aged for 15 min and for 1 week. Results from both capacitively and inductively plasma polymerized polystyrene (pPS) films aged for 15 min showed that the chemical structure of the bulk, chemical composition of the surface (depth < 10 nm) and wettability properties were rather similar. Only their microstructures were very different: the pPS_capa film's microstructure showed homogeneous distribution of spherical particles of about 100 nm in diameter but the pPS_ind film's microstructure seemed to be mainly influenced by the surface of the metallic substrate: orientated ‘lamellae‐like layers’ of polymers were observed on each metallic grain. Ageing for 1 week in ambient air induced low oxygen uptake in the surface of both pPS films. The pPS_ind topmost surface (depth < 3 nm) was more oxidized than that of pPS_capa but no modification of the chemical structure of the bulk or of the morphology was noticed after ageing. Copyright © 2006 John Wiley & Sons, Ltd.     

JEE—4x型真空镀膜仪功能扩展

报道了对ＪＥＥ－４ｘ型真空镀膜仪蒸发装置的改进以及建立蒸发材料回收装置的具体方法，并介绍了改进后该仪器在高分辨扫描电镜样品制备上的应用实例．实验证明，上述改进不但扩展了ＪＥＥ—４ｘ型真空镀膜仪的制样功能又节省了蒸发材料，集中了离子溅射法及常规高真空镀膜法的优点，完全满足ＳＥＭ样品的分析要求，该方法简单易操作．     

Copper corrosion in buffered and non-buffered synthetic seawater: a comparative study

The electrochemical behaviour of copper in neutral buffered and non-buffered synthetic seawater and in pure chloride solutions has been studied by cyclic voltammetry, weight loss measurements, open circuit potential and scanning electron microscopy (SEM). Values of the repassivation potentials of Cu in non-buffered and buffered synthetic seawater, at 50 mV s^–1, were 0.12 and 0.46 V vs. SCE, respectively. The sharpness, heights and location of the different peaks as well as their charges were shown to be influenced by the composition of the solution, buffering conditions, deoxygenation, polarization potential and time. High chloride concentrations lead to higher oxidation charges. The anodic and the cathodic charges were shown to increase as the chloride concentration increases. The open circuit potential transients of copper in non-deoxygenated, non-buffered synthetic seawater indicate pitting from the beginning of the exposure, while in buffered solutions the pitting appeared only after a quite long exposure period, i.e. after 40 days. Corrosion rates of Cu samples after 3 months of immersion were higher in solutions of pure chloride (0.5 M) than in synthetic seawater. After six months the differences were even more noticeable. SEM images have showed a somewhat higher density of pits on copper samples immersed in the chloride solution (0.5 M), in comparison with those in synthetic seawater.     

Loss and recovery in hydrophobicity of silicone rubber exposed to corona discharge

This paper describes the loss and recovery in the hydrophobicity of unfilled high temperature vulcanized silicone rubber (HTV-SR) resulting from corona discharge. In this study, HTV-SR specimens were exposed to corona stress generated by a parallel needle-plane electrode system, and physicochemical analyses on the surface layer of SR before and after corona discharge treatment were carried out by using Fourier transform infra-red (FTIR) spectroscopy, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). It is demonstrated that hydrophilic OH groups that are by-products of ageing can be formed instead of hydrophobic CH₃ groups on the surface of aged SR and the corona discharge plays an important role on the temporary loss of hydrophobicity. After a substantial period of ‘rest’, the hydrophobic recovery of SR results from the diffusion of low-molecular weight (LMW) silicone fluid from the bulk onto the aged layer.