Coulometric argentometric determination of microamounts of sulphur in iron and steel after reduction to hydrogen sulphide with iron(II) in strong phosphoric acid medium

A coulometric method was developed for the determination of microamounts of sulphur in iron and steel. Hydrogen sulphide is quantitatively evolved by reduction with iron(II) in strong phosphoric acid medium and is titrated with electrolytically generated silver ion from a silver anode. Microamounts of sulphide (2.96–224.3 μg) in sodium sulphide standard solutions could be determined with an error of only a few percent. Sulphur in a potassium sulphate standard solution is quantitatively reduced to hydrogen sulphide and could be separated from the solution by heating and determined accurately. Trace amounts of sulphur (7–100 μg g^?1) in iron and steels could be determined with a standard deviation of 0.7–2.1 μg g^?1.     

Development of new lubricating grease formulations using recycled LDPE as rheology modifier additive

The recovery of plastic waste but also its applicability in product development may be an incentive to industry, since the use of such plastics represents a cheaper source of raw material. The aim of the present paper is to study the feasibility of recycling polyolefins as additives to improve the rheological properties of lithium 12-hydroxystearate lubricating greases. The effects that both soap and recycled low-density polyethylene (LDPE) concentration exert on the rheology of lithium lubricating greases and its relationship with grease microstructure are discussed in this work. In this way, different lubricating grease formulations were manufactured by modifying the concentration of lithium 12-hydroxystearate and content of recycled LDPE, according to a RSM statistical design. These lubricating greases were rheologically characterized through small-amplitude oscillatory shear (SAOS) and viscous flow measurements. In addition to these, scanning electronic microscopy (SEM) observations and mechanical stability tests were also carried out. Recycled LDPE was found to be an effective additive to modify grease rheology, acting as filler in the soap entangled microstructure. The values of both apparent viscosity and viscoelastic functions in the linear viscoelastic region increase with soap and recycled polymer concentrations. However, the addition of recycled LDPE distort the microstructural network of these greases resulting greases with less relative elastic characteristics and poorer mechanical properties as LDPE content increases.     

Study and characterization of virgin and recycled LDPE/PP blends

Recycling of mixed plastic wastes composed of low-density polyethylene (LDPE) matrix and polypropylene (PP) was carried out by compounding using single-screw or twin-screw extruders. Blends of virgin polymers have been prepared to compare mechanical properties of both virgin and regenerated materials. First, a model composition of virgin LDPE/PP blend was prepared to study the effect of process parameters and that of different types of compatibilizers. Second, the results were applied to plastic wastes coming from industrial post-consumer plastic wastes. By adding compatibilizing agents such as ethylene-propylene-diene monomer, ethylene-propylene monomer, or PE-g-(2-methyl-1,3-butadiene) graft copolymer, elongation at break and impact strength were improved for all blends. The effect of these various copolymers is quite different and is in relation with their chemical structure. The recycled blends exhibit suitable properties leading to applications that require good mechanical properties.     

The way to measure quantitatively full dissolution and crystallization of polyamides in water up to 200 °C and above by DSC

The way to measure quantitatively full dissolution and crystallization of polyamides in water up to 200 °C and above by DSC is described. Stainless-steel high-pressure pans enable research on fully dissolving polyamides in water under vapor pressure. The results show clearly that polyamide 6 (PA6) is soluble in water under vapor pressure in the whole concentration range and that water acts as a crystallization and melting point suppressor. The maximum temperature depression is approximately 60 °C. This depression of the transitions is independent of concentration over a large range (10-70 mass% PA6 in water). When PA6 dissolves in water during heating, the polymer often sets to the sides of the DSC sample pan. Because of this the contact between the sample and the bottom of the pan reduces during measurement and therefore DSC heating curves are frequently curved. Adding steel wool to these stainless-steel high-pressure pans improves the measurements by increasing the thermal conductivity between the sample and pan bottom, and as a result the DSC curves become less curved. The interpretation of the measurements improves and the possibility of reproducible peak area calculations also in heating comes in sight.     

热致型液晶聚合物的近晶相结构研究

本文借助于不同热处理样品的WAXD研究和变温FTIR分析,从液晶态与结晶态面间距的变化,晶态、液晶态和各向同性液态下结构构象的差异出发,研究了聚合物液晶态下的近晶相结构模型。     

The Photochemistry of Ch3I in Various Matrices at Low Temperature

The photodissociation of methyl iodide in various matrices at low temperature was studied. The observed Raman spectra excited by 514.5 nm laser radiation showed that there were two different photolytically produced iodine species isolated in the matrices after illumination by a medium pressure mercury lamp. One species which was dominant at lower iodine concentrations and exhibited a progression with an ωe of 201 cm^?1, belonged to the matrix isolated iodine monomer (I₂). The other species, which was dominant at higher iodine concentrations with an ω_e of approximately 180 cm^?1, belonged to the iodine aggregate ((I₂)_n). Five progressions of resonance Raman or resonance fluorescence of these two species were also observed in the other matrices. The iodine aggregate in the methyl iodide matrix at 77 K was formed in a crystalline structure, while the photolytically generated iodine aggregate from CH₃I/Ar (2/3) matrix at 10 K, after illumination with a mercury lamp, was in amorphous form. The rearrangement of photolytically produced iodine aggregate in methyl iodide matrix was observed as a function of the duration of illumination. Local heating effects of the laser radiation might induce the iodine monomer to aggregate in matrices. The photodissociation mechanism of methyl iodide in matrices is also proposed.     

Tying together the ultrastructural modifications of wood fibre induced by pulping processes with the mechanical properties of paper

The composition and ultrastructural arrangement of cell wall polymers in wood fibres have determining influence on the properties of wood derived materials. It is therefore important to improve our understanding of the relationship between fibres organisation, the modifications induced by pulping treatments, and the resulting paper sheet mechanical properties. The different treatments to which fibres are subjected during the manufacturing of pulps and papers induce morphological and micro-structural alterations due to the removal of wall constituents and of microfibrillar elements. The impact of pulping processes on fibres was investigated at the ultrastructural scale of transmission electron microscopy. Particular attention was given to the effects of beating in refiners at various intensities on the ultrastructure of fibres. The most characteristic effects consisted of delaminations, microfibril disorganisation, and even fractures, of varying importance depending on the intensity of the mechanical refining. The consequences of internal alterations and surface modifications of the fibres were examined in relation to the paper sheet mechanical properties. Correlations between the type of alteration observed in the fibres and its possible impact on a given paper mechanical property are suggested. With similar approaches, the effects of drying and recycling were studied.     

42CrMo钢回火方程的建立

通过回归分析给出了４２ＣｒＭｏ钢的回火硬度、回火温度及回火时间的函数关系式。该关系式具有精度高，使用方便。同时分析了回火参量Ｐ＝ｆ［Ｔ（Ｃ＋ｌｇτ）］的算法，指出了其存在较大误差的原因