准分子激光全固态脉冲电源设计与实验研究

针对脉冲能量5~8 mJ的ArF准分子激光器,设计了基于可控硅开关结合三级磁脉冲压缩开关的全固态脉冲电源,采用国产可控硅和磁开关材料,获得了上升时间约150 ns,电压10~14 kV,传递能量0.35~0.68 J的激励脉冲,并实现了对准分子激光器快放电激励。三级磁开关总效率35%,分析表明磁开关损耗较大主要原因为电容能量转移不充分、导线铜损及磁芯材料铁损较大,并提出了相应改进办法。     

光学薄膜激光诱导损伤机理研究

基于电子密度演化模型,借助数值方法,研究了飞秒激光作用下光学薄膜内的电子密度演化过程,讨论了初始电子密度Ni和激光脉冲宽度τ对光学薄膜激光损伤阈值Fth的影响,分析了激光诱导薄膜损伤过程中MPI和AI的性质和作用.研究结果表明,对应于一定的脉宽,存在一个临界初始电子密度,当Ni低于这一临界密度时,Fth不受Ni影响;当Ni高于临界密度时,Fth随Ni增加而降低.临界初始电子密度随着脉宽的减小而增加。对于FS和BBS介质薄膜,Fth随脉宽的增加而升高。初始电子密度Ni对BBS中的MPI和AI基本没有影响;同样Ni对FS中的AI基本不产生影响,但当Ni>1011 cm－3时,FS中MPI电子密度随Ni增加而降低.在所研究的脉宽范围τ∈［0.01,5］ps,AI是FS介质激光诱导损伤的主要机制.而对于BBS,当脉宽τ∈［0.03,5］ps,AI是激光诱导损伤的主要机制;当脉宽τ∈［0.01,0.03］ps,MPI在激光诱导损伤中占主导地位.     

Soft X-ray induced chemical modification of polysaccharides in vascular plant cell walls

Scanning transmission X-ray microscopy and micro carbon X-ray Absorption Near Edge Spectroscopy (C-XANES) can provide quantitative information regarding the distribution of the biopolymers cellulose, hemicellulose, and lignin in vascular plant cell walls. In the case of angiosperms, flowering plants, C-XANES may also be able to distinguish variations in lignin monomer distributions throughout the cell wall. Polysaccharides are susceptible to soft X-ray irradiation induced chemical transformations that may complicate spectral analysis. The stability of a model polysaccharide, cellulose acetate, to variable doses of soft X-rays under conditions optimized for high quality C-XANES spectroscopy was investigated. The primary chemical effect of soft X-ray irradiation on cellulose acetate involves mass loss coincident with de-acetylation. A lesser amount of vinyl ketone formation also occurs. Reduction in irradiation dose via defocusing does enable high quality pristine spectra to be obtained. Radiation induced chemical modification studies of oak cell wall reveals that cellulose and hemicellulose are less labile to chemical modification than cellulose acetate. Strategies for obtaining pristine C-XANES spectra of polysaccharides are presented.     

Radiation damage from EELS and NEXAFS in diesel soot and diesel soot extracts

Carbon NEXAFS and EELS spectra of soot, and NEXAFS spectra of soot extracts, are presented. The EELS spectra of solid soot particles from a TEM-EELS show fewer structures than the corresponding NEXAFS spectra obtained at two different synchrotron beamlines. We attribute radiation damage in the TEM-EELS to the failure at resolving structures of surface functional carbon groups in or on soot. NEXAFS spectra of soot extracts studied with a scanning transmission X-ray microscope show alterations during X-ray exposure, which can be explained by a simple chemical model where oxygen apparently reacts with the sample. When the same extract is studied in an ultrahigh-vacuum beamline, no such alterations are observed.     

Controlling subsurface damage in neodymium-doped phosphate glass

We investigate the removal mechanism of neodymium-doped phosphate glass dominated in loose abrasive grinding and bound abrasive grinding. Moreover, we investigate the surface roughness and subsurface damage change with optical fabrication parameters, such as different spindle speed, load and abrasive size under different grinding processes in details. For a range of experimental conditions, we find that fracture is the principal removal mechanism for loose abrasive grinding, while plastic scratching is the dominating mechanism for bound abrasive grinding. The load has more influence on subsurface damage for bound abrasive grinding than for loose abrasive grinding. However, the spindle speed has different effect on subsurface damage produced with loose abrasive grinding and bound abrasive grinding. Moderate spindle speed and low load is preferred to produce smaller subsurface damage for loose abrasive grinding. Moreover, higher spindle speed and lower load are preferred to plastic scratching for bound abrasive grinding. Bound abrasive grinding produces 4 times lower surface roughness and 3 times lower subsurface damage than loose abrasive grinding.     

HOMOTOPY CONTINUATION ALGORITHM FOR STRUCTURAL DAMAGE IDENTIFICATION

I. INTRODUCTIONStructural damages due to the loss of sti?ness such as crack, localization bulking have remarkablein?uences on the physical properties of structure such as deformation, stress, frequency and modelshape. So the change of these properties can be used to identify the damage location and degree ofstructures. The damage identification techniques based on these properties’ changes have attractedmuch attention in recent years, and many approaches have been developed[1??5].Nowaday…     

石英玻璃低能质子辐照损伤动力学研究

地面模拟研究了JGS3光学石英玻璃在真空、热沉和能量低于200keV的低能质子辐照下表面光学性能变化的基本规律．并建立了辐照损伤色心演化的动力学唯象模型。试验结果表明．大通量低能质子辐照对石英玻璃表层具有明显的表面损伤效应。随着辐照吸收剂量的增加,光密度变化先以线性规律迅速增加．加进一步增加时逐渐呈现饱和趋势;采用较高能量辐照作用后光密度变化出现饱和趋势的拐点提前,且饱和数值降低。根据对试验结果的分析,建立了低能质子辐照下石英玻璃色心演化的动力学模型．并给出了光密度变化的表达式。采用模型结果进行数学模拟,模拟曲线与试验结果曲线相似。因此所建立的动力学模型可以用来定量描述低能质子辐照下石英玻璃光学性能随辐照吸收剂量的变化规律。     

PMMA光纤辐照特性研究

分析了聚合物光纤在辐照环境下的物理化学变化,实验研究了聚甲基丙烯酸甲脂（PMMA）光纤在不同剂量的γ射线辐照下的辐照损伤和恢复特性,测量了PMMA光纤在可见光波段的辐照光谱和恢复光谱以及在638 nm的辐照前后透过率及辐照损伤.测量结果表明,光纤的辐照损伤和恢复都有波长相关性,辐照剂量低于5 kGy,PMMA光纤在整个可见光波段的辐照损伤情况差别不大,辐照剂量超过5 kGy,PMMA光纤在400 nm~550 nm波段的辐照损伤比600 nm~800 nm的辐照损伤要严重.     

脉冲激光辐照光学薄膜的缺陷损伤模型

建立了缺陷吸收升温致薄膜激光损伤模型,该模型从热传导方程出发,考虑了缺陷内部的温度分布以及向薄膜的传导过程,通过引入散射系数简化了Mie散射理论得出的吸收截面.对电子束蒸发沉积的ZrO₂:Y₂O₃单层膜进行了激光破坏实验,薄膜样品的损伤是缺陷引起的,通过辉光放电质谱法对薄膜制备材料的纯度分析发现材料中的主要杂质元素为铂,其含量为0.9％.利用缺陷损伤模型对损伤过程进行了模拟,理论模型和实验结果取得了较好的一致性.     

衍生化-毛细管气相色谱法同时测定糖尿病大鼠坐骨神经中葡萄糖、山梨醇、肌醇

建立了大鼠坐骨神经中糖醇化合物葡萄糖、山梨醇、肌醇同时测定的毛细管气相色谱分析方法。选择甘露糖为内标,先加入盐酸羟胺吡啶溶液进行肟化反应,再加入乙酸酐溶液进行乙酰化反应,将葡萄糖、山梨醇、肌醇转化成糖腈乙酰酯化合物,经SE 30毛细管柱色谱分离,氢火焰离子化检测器检测。葡萄糖、山梨醇、肌醇的回收率均在93%以上,其检出限分别为0.40、0 30、0.26ng/μL。对比测定了正常对照组、糖尿病组、某中药复方治疗组大鼠坐骨神经中以上3种糖醇含量。