Effects of Total Thermal Balance on the Thermal Energy Absorbed or Released by a High-Temperature Phase Change Material

Front tracking and enthalpy methods used to study phase change processes are based on a local thermal energy balance at the liquid–solid interface where mass accommodation methods are also used to account for the density change during the phase transition. Recently, it has been shown that a local thermal balance at the interface does not reproduce the thermodynamic equilibrium in adiabatic systems. Total thermal balance through the entire liquid–solid system can predict the correct thermodynamic equilibrium values of melted (solidified) mass, system size, and interface position. In this work, total thermal balance is applied to systems with isothermal–adiabatic boundary conditions to estimate the sensible and latent heat stored (released) by KNO3 and KNO3/NaNO3 salts which are used as high-temperature phase change materials. Relative percent differences between the solutions obtained with a local thermal balance at the interface and a total thermal balance for the thermal energy absorbed or released by high-temperature phase change materials are obtained. According to the total thermal balance proposed, a correction to the liquid–solid interface dynamics is introduced, which accounts for an extra amount of energy absorbed or released during the phase transition. It is shown that melting or solidification rates are modified by using a total thermal balance through the entire system. Finally, the numerical and semi-analytical methods illustrate that volume changes and the fraction of melted (solidified) solid (liquid) estimated through a local thermal balance at the interface are not invariant in adiabatic systems. The invariance of numerical and semi-analytical solutions in adiabatic systems is significantly improved through the proposed model.     

聚1-氨基蒽醌在二次锂电池正极材料中的应用

采用化学方法合成聚1-氨基蒽醌并用于二次锂电池正极材料,通过红外光谱、扫描电镜、粒度测试、循环伏安以及充放电测试等方法对材料的官能团结构、微观形貌、颗粒大小以及电化学性能等进行了研究与分析.实验表明,与金属锂组成二次锂电池后,聚1-氨基蒽醌达到了218.3 mAh•g－1的首次放电容量,经过25次循环后仍可保持较高的充放电效率.由于材料具有较高的能量密度且不含对环境有污染的元素S,因此是二次锂电池非常有希望的正极材料.     

有机元素微量分析标准物质——茴香酸的研制

茴香酸的分子式为C_8H_8O_3,碳含量63.15%、氢含量5.30%、氧含量31.55%、甲氧基含量20.40%。该标样与日本元素分析恳谈会委员会、英国化学协会微量化学委员会所公布的微量化学标样之一——香草醛一样,都具有相同的碳、氢、氧和甲氧基含量,美国国家标准局(NBS)发行SRM142茴香酸作为微量分析中甲氧基的分析标样。     

高温固相法合成LiNi1/3Mn1/3Co1/3O2及其性能研究

采用高温固相法合成出层状锂离子电池正极材料LiNi_1/3Mn_1/3Co_1/3O₂。通过XRD、ICP、SEM和电化学测试手段对产物的结构、组成、形貌及电化学性能进行了研究。XRD结果表明此方法合成的LiNi_1/3Mn_1/3Co_1/3O₂具有标准的α-NaFeO₂型层状结构，SEM照片显示颗粒粒径大约在500 nm左右，粒径分布较窄。以20 mA·g^-1电流密度放电，充放电电压在2.8～4.4 V之间，其首次放电比容量为170 mAh·g^-1，40次循环容量保持率为85.3%。进一步加入石墨导电剂后，同样条件下首次放电比容量变为179 mAh·g^-1，50次循环容量保持率为89.6%。容量衰减主要发生在前10次循环。XRD和SEM测试表明循环初期容量衰减的原因是由材料本体结构变化和界面反应共同作用的结果。     

Mechanical properties decay and morphological behaviour of biodegradable films for agricultural mulching in real scale experiment

The use of plastic materials in agriculture causes the serious drawback of huge quantities of waste. The introduction of biodegradable materials, which can be disposed directly into the soil, can be one possible solution to this problem. Biodegradable materials are actually innovative materials; therefore, their physical properties must be evaluated in relation to their functionality during the use in field. In the present research results of experimental tests carried out on biodegradable films used in strawberries protected cultivation are presented. The decay of some relevant physical parameters of biodegradable films during the cultivation period was monitored by laboratory tests (SEM analysis, mechanical tensile tests and infrared reflectance spectroscopy). Infrared spectroscopy clearly indicated that the mechanical degradation starts from the starch component of the material. Tensile tests showed that the value of elongation at break of biodegradable materials decreased in some cases by 300% after 10 days of field application.     

Normalized Dynamic Characterization and Application of Multiple Heat Storage Materials Based on Standard Thermal Resistance北大核心CSCD

基于标准热阻和能量流法,推导出储热材料与换热流体的瞬态换热热阻,通过类比电路分析法,获得了储热-换热过程的瞬态热量流模型及动态响应时间常数。进一步引入节点温度,重新定义换热热阻,获得了储热与换热过程耦合的三阶电路瞬态热量流模型,求解得到了加热、储热和释热三类时间常数,可用于协同表征储热材料中储热与释热的快慢程度,从而实现了多类储热材料的归一化动态表征。通过数值模拟验证与应用对比分析,发现基于多时间常数的归一化动态模型用于表征储热材料的动态特性是可行的,可直接对不同换热、储热材料进行对比分析。案例分析发现与固体储热材料换热时,液态金属的动态换热能力优于熔融盐,而相比于水蒸气和CO₂,空气与陶瓷材料换热能更快达到稳态。     

智能材料与智能建筑结构

综述了智能材料与智能蛄构的研究与应用,着重论连了智能材料应用在建筑工程中彤成智能建筑结构,使建筑结构本身不仅具有承受荷戢的能力,而且还具有识别、分析、判断和驱动功能及自诊断、自适应和自修复功能。     

贮氢合金的开发与研究进展

贮氢合金是近年来开发的一类新型高性能材料。本文介绍了贮氢合金的开发和研究的最新进展,论述了它在氢的提纯、热泵、空调、压缩机和镍—氢化物电池等高技术领域中的应用前景。     

复合材料设计的原理与实践

对复合材料设计的原理与实践进行简要介绍,对其研究现状与发展趋势进行评述．重点在于工程结构复合材料,特别是航空航天领域应用的先进复合材料,重点是仿生与机敏材料设计,材料设计的目的是实现材料性能优化．     

2,3-二羟基哌嗪与几种氨基化合物的缩合反应研究

由乙二胺与乙二醛的缩合物２,３－二羟基哌嗪,分别与甲酰胺、脲和乙二胺反应,制得２,４,７,９,１１,１４－六氮杂三环［８,４,０,０３,８］十四烷六盐酸盐四水合物（１）,２,５,７,９－四氮杂双环［４,３,０］壬－８－酮二盐酸盐－水合物（２）和２,５,７,１０－四氮杂双环［４,４,０］癸烷（３）。化合物１为未见文献报道的新化合物。化合物２的合成工艺条件优化后,反应得率与文献［１］相比有一定提高。化合物３的合成,由于将反应分为低温和高温两个缩合阶段,使反应得率提高到７７．５％。