Chemical environment of copper at the surface of a CuAl2 model alloy: XPS,MEIS and TEM analyses

Air‐formed oxide on a CuAl₂ model alloy is shown to be free of copper species, with copper enriching in the alloy. With thickening of the oxide by anodizing, copper enriches further to a critical concentration at which its oxidation proceeds with incorporation of Cu(II) species into the film. Such species migrate more rapidly through the film than aluminium species. Incorporation of copper species is associated with generation of oxygen gas within the film and subsequent film rupture is due to release of the gas. Reduction of Cu(II) to Cu(I) species during XPS analysis is characterized and the accelerating role of charge neutralizing is highlighted. Copyright © 2004 John Wiley & Sons, Ltd.     

富镧混合稀土对ZL101A合金组织和机械性能的影响

研究了富镧混合稀土对ＺＬ１０１Ａ合金的铸态、固溶态、Ｔ６状态、重熔态的组织和机械性能的影响，提出了混合稀土中入量低压铸造整体车轮合理的热处理状态。     

Formation of Bi-Sb, Bi-Sn, and Bi-Sb-Sn Nanoclusters in Silica Xerogel Matrices from Mixed-Metal Oxide Precursors

Homogeneous mixed-metal oxides of the general formula (Bi/E/Si)O _x , where E represents a dopant element (E=Sb, Sn, or Sb/Sn), can be prepared using typical sol-gel processing techniques. Reduction of the in-situ Bi(III) and E ions by hydrogen affords nanocomposites of Bi-Sb, Bi-Sn, or Bi-Sb-Sn widely dispersed throughout the silica xerogel matrix. The materials prepared have high Bi-E metal loading of 52–60 wt. % containing Bi-E alloy nanoclusters of 12–15 nm average diameter. These results demonstrate a convenient method for the production of practical quantities of nanostructured bismuth alloy ceramic composites at high metal content.     

高分子合金分离膜材料及结构研究进展

膜材料液相共混制备高分子合金分离膜不但可以调节膜材料与被分离物的亲和性，也在一定程度上改变了膜的结构。本文介绍高分子材料浓相共混对膜材料的亲水性、耐污染性及其它理化性能的影响和对膜结构的调节作用，同时指出高分子材料间的相容性是影响合金膜结构的重要因素。     

X-射线荧光光谱法测定钛铁中的硅、锰、磷、铝

介绍用X-射线荧光光谱仪测定钛铁中Si、Mn、P、Al含量的方法,通过试验确定了合适的研磨时间、压力和保压时间,用压片法制样,建立了各元素的工作曲线,各元素的测定范围分别为Si3.00%～6.00%,Mn1.00%～3.00%,P0.030%～0.070%,Al5.00%～9.00%。通过强度测量得到测定Si、Mn、P、Al的相对标准偏差分别为0.074%、0.308%、0.383%、0.040%,精密度满足测试要求。将该方法测定结果与化学法比对,准确度满足国家标准方法分析误差的要求。     

Characterization of non‐Cr‐based deoxidizers on Al alloy 7475‐T7651

The effects of three non‐chromate‐based deoxidizers, namely NaBrO₃/HNO₃, (NH₄)₄Ce(SO₄)₄/H₂SO₄ and Fe(III)/HF/HNO₃, on the Al alloy 7475‐T7651 were investigated. Several analytical methods were employed, including SEM, AES, transmission electron microscopy (TEM), electron energy‐loss spectroscopy (EELS) and glow discharge optical emission spectrometry (GDOES), to study the effects on the surface of this alloy after each treatment compared with the as‐received and alkaline‐cleaned alloy surfaces. The untreated alloy was found to have a thick oxide of 200–320 nm, consisting mainly of MgO. Alkaline cleaning results in an etching effect that thins the oxide and also deposits a thin silicate layer on the surface. In the case of the deoxidizers, there is significant removal of the native oxide of the alloy by the NaBrO₃/HNO₃ deoxidizer. There is also evidence of intermetallic attack on the alloy. The (NH₄)₄Ce(SO₄)₄/H₂SO₄ deoxidizer, which is a low‐etch‐rate deoxidizer, resulted in a slight thinning of the oxide. However, the effect was not significantly greater than with alkaline cleaning alone. The most effective deoxidizer in reducing the oxide thickness of the alloy is Fe(III)/HF/HNO₃, in which the etch rate was sufficiently high to remove completely the native oxide. In this case, equilibrium between oxide removal and the formation of new oxides on the alloy surface was achieved. Copyright © 2004 John Wiley & Sons, Ltd.     

弯曲铝合金方管的轴压性能试验研究

为研究带初弯曲度铝合金方管的轴压承载力,完成了8个试件的轴压稳定性试验,并建立了与试验条件一致的有限元模型。通过对比试验和有限元分析结果验证了有限元模型的可靠性。结果表明,带有较大初弯曲度铝合金方管的破坏模式为整体弯曲失稳。最后,根据有限元分析结果拟合得到较大初弯曲度铝合金方管的整体稳定系数计算式,并将拟合计算式结果和数值分析结果及试验结果进行对比,验证了计算式的正确性。     

电子束熔化成形与锻造Ti6Al4V合金的腐蚀行为对比研究

本工作采用电化学工作站研究了电子束熔化技术（EBM）成形TC4样品和传统锻造TC4在3.5wt% NaCl溶液中的电化学腐蚀行为. 结果表明EBM成形TC4样品的非平衡微观结构使其与传统锻造的TC4相比,表现出不同的耐腐蚀性. EBM成形TC4样品与锻件TC4相比,EBM成形样品不同平面存在耐蚀性差异,而且EBM水平面大于锻件,EBM垂直面小于锻件. EBM成形TC4样品垂直面出现的腐蚀性能的各向异性主要是β柱状晶导致的. 在腐蚀的过程中,点蚀优先发生在α晶界,因为晶界能量较高,形成多孔的钝化层. 本项工作有助于丰富增材制造制备TC4合金在航空钛合金领域的腐蚀性能研究.     

An orthotropic plate model for decks of suspension bridges

The main purpose of the present paper is to compare two different kinds of approaches in modeling the deck of a suspension bridge: in the first approach we look at the deck as a rectangular plate and in the second one we look at the deck as a beam for vertical deflections and as a rod for torsional deformations. Throughout this paper we will refer to the model corresponding to the second approach as the beam-rod model. In our discussion, we observe that the beam-rod model contains a larger number of elastic parameters if compared with the isotropic plate model. For this reason the beam-rod model is supposed to be more appropriate to describe the behavior of the deck of a real suspension bridge. A possible strategy to make the plate model more efficient could be to relax the isotropy condition with a more general condition of orthotropy, which is expected to increase the number of elastic parameters. In this new setting, a comparison between the two approaches becomes now possible.Basic results are proved for the suggested problem, from existence and uniqueness of solutions to spectral properties. We suggest realistic values for the elastic parameters thus obtaining with both approaches similar responses in the static and dynamic behavior of the deck. This can be considered as a preliminary article since many work has still to be done with the perspective of formulating models for a complete suspension bridge which take into account not only the deck but also the action on it of cables and hangers. With this perspective, a section is devoted to possible future developments.     

非对称碰撞约束下形状记忆合金梁的随机响应与分岔

形状记忆合金(SMA)是二十一世纪具有形状记忆效应的新型智能材料.针对具有非对称约束的SMA梁,本文构造了碰撞振动系统.在无碰撞和有碰撞两种情况下,利用随机平均法给出了近似解析结果.数值模拟作为验证解析结果的工具.结果表明,系统能量的概率响应曲线具有非光滑特性.当约束位置发生变化时,系统会出现随机P分岔和D分岔.