Mossbauer investigations of corrosion environment influence on Fe valence states in oxide films of zirconium alloys

Mössbauer investigations about iron atom redistribution in oxide films of zirconium alloys subjected to corrosion at 500°C in pure oxygen and water pair have been analysed. The alloys were also subjected to autoclave conditions at a pressure of 10.0 MPa and autoclave conditions at 350°C and at a pressure of 16.8 MPa, using distilled water and water with additives of lithium and fluorine. It is shown that, depending on the corrosion environment, various compounds of iron, such as α-Fe₂O₃, Fe₃O₄, and FeO, as solid solutions of iron in ZrO₂ are formed in oxide films.     

侵彻环境下两种钨合金的细观响应特性

本文实验发现具有较大密度和较高速度的93W钨合金长杆模拟弹的穿靶深度反而比密度较小，速度较低的90W钨合金长杆弹的穿靶深度小．针对这一现象，本文从两种材料在侵彻环境下的细观响应特性的差异上给出了有实验根据的合理分析，结论是90W在侵彻环境下较易于形成绝热剪切带，从而在弹头部发生“自锐化”效应所致．     

Microstructure transition of Al-Cu eutectic alloy during containerless rapid solidification

Droplets of Al-32.7%Cu eutectic alloy were rapidly solidified during containerless processing in a 3 m drop tube. The microstructural evolution of Al-Cu eutectic alloy depends strongly on droplet size. The eutectic growth morphology changes from regular lamellar eutectic to a kind of anomalous eutectic with the decrease in droplet size. This microstructural transition was analyzed within the current theories of eutectic growth. The results indicate that there exists a critical velocity for eutectic growth beyond which anomalous eutectic appears. The coupled zone of the Al-Cu eutectic alloy system has been calculated on the basis of the Trivedi-Magnin-Kurz(TMK) eutectic growth and the Lipton-Kurz-Trivedi(LKT)/Boettinger-Coriell-Trivedi(BCT) dendrite growth models, which provides a further interpretation for the morphological transition.     

钙和钡对钢脱氧及夹杂变性的理论分析

在比较了各种常用脱氧剂单质脱氧能力的基础上，对钙合金、钡合金夹杂的变性能力进行了理论分析和探讨，并对钡合金的脱氧和夹杂物变性工艺提出了建议。     

Specific heat and related thermophysical properties of liquid Fe-Cu-Mo alloy

The specific heat and related thermophysical properties of liquid Fe77.5Cu13Mo9.5 monotectic alloy were investigated by an electromagnetic levitation drop calorimeter over a wide temperature range from 1482 to 1818 K. A maximum undercooling of 221 K (0.13 Tm) was achieved and the specific heat was determined as 44.71 J·mol-1·K-1. The excess specific heat, enthalpy change, entropy change and Gibbs free energy difference of this alloy were calculated on the basis of experimental results. It was found that the calculated results by traditional estimating methods can only describe the solidification process under low undercooling conditions. Only the experimental results can reflect the reality under high undercooling conditions. Meanwhile, the thermal diffusivity, thermal conductivity, and sound speed were derived from the present experimental results. Furthermore, the solidified microstructural morphology was examined, which consists of (Fe) and (Cu) phases. The calculated interface energy was applied to exploring the correlation between competitive nucleation and solidification microstructure within monotectic alloy.     

电磁相分离法制备自生表层复合材料

采用电磁相分离法制备出以初生富铁相（AlSiFeMn复杂金属间化合物）为增强相，表层硬度为HB62．25，基体硬度为HB59．00的Al-11.70%Si-1.20?-1.50%Mn合金自生表层复合材料，增强相的显微硬度为HV 842。87，大小为20－80μm，该表层复合材料同基体材料相比，耐磨性提高了57．41％，所用方法工艺过程简单，成本低，为解决材料在服役环境中不同部位，不同性能的问题提供了新途径。     

铜基合金中马氏体穿晶行为的研究

在形状记忆合金中,存在马氏体穿晶生长现象,它是热弹马氏体相变在小角晶界的行为。     

室温下压致铁钴镍合金的bcc→hcp相变

 本文采用高压X光衍射方法在金刚石对顶压砧中在位地（in situ）研究了Fe₆₈Co₂₄Ni₈（wt%）合金在室温下的压致bcc→hcp结构相变和直到40.5 GPa的等温压缩行为。实验结果表明该合金在常压下为bcc结构，晶格常数a₀=(0.287 0±0.000 1) nm，体积V₀=(7.119±0.007) cm³/mol，密度ρ₀=(7.981±0.008) g/cm³；在20.9 GPa附近出现bcc→hcp结构相变，两相共存压力区约10 GPa，在此区域内有晶面间距d(002)_hcp=d(110)_bcc，且原子平面(002)_hcp//(110)_bcc，hcp相比bcc相体积减小(0.33±0.02) cm³/mol；高压相hcp结构的晶格参数比值c/a=1.608±0.004；相变后原子配位数的增加使得hcp相(002)平面内及(002)平面间的最近邻原子间距比bcc相最近邻原子间距分别增大约1.6%和0.5%；用Murnaghan状态方程对实验数据进行最小二乘法拟合，得到bcc相B₀=(130±13) GPa，B₀'=12.6±0.5；hcp相V₀=(6.62±0.04) cm³/mol，B₀=(243±21) GPa，B₀'=6.8±0.3；对于该合金的bcc→fcp相变时的结构转变机制做了详细的讨论。     

Experimental Study on the Milling of a Ti Beta 21S

Ti Beta 21S (Ti-15Mo-2.7Nb-3Al-0.2Si) was devel op ed by TIMET in 1989. It is a metastable beta titanium alloy that offers subs tantial weight reductions over other engineering materials. Compared with common beta Ti alloys, it offers the high specific strength, good cold formability, im proved oxidation resistance, elevated temperature strength, creep resistance, an d thermal stability. Besides the common characters of titanium alloy, such as po or heat diffusivity, low elastic modulus, Ti Beta 21S has ...     

Mössbauer effect study of the decagonal quasicrystal Al65Co15Cu20

The ⁵⁷Fe Mössbauer effect study at 5.0 K and in an external magnetic field of 9.0 T on a high-quality stable decagonal quasicrystal Al₆₅Co₁₅Cu_19.9Fe_0.1 is presented. It is shown that the iron atoms are located in two distinct classes of sites. The values of the principal component of the electric field gradient tensor and the asymmetry parameter at these sites are, respectively, ?1.90(10)?×?10²¹ V/m², 0.97(15) and ?3.95(12)?×?10²¹ V/m², 0.00(17).