Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

对煤矿岩体中固流耦合效应问题研究的探讨

本文对固流耦合效应的基本概念、基本原理进行了简单介绍。并对采动影响下邻近煤层、岩层的瓦斯向本层采空区的流动规律,以及煤和瓦斯突出的机理和发生的理论,分别作为固流耦合效应的两类不同问题进行了研究.同时提出了今后进行进一步研究的看法。     

低密度聚乙烯光引发交联机理——Ⅱ.BNB自旋捕捉ESR研究

在光引发剂二苯甲酮(BP)存在下,紫外光辐照低密度聚乙烯(LDPE)所形成的自由基中间体已被自旋捕捉剂2,4,6-三特丁基亚硝基苯(BNB)所捕捉,其自旋加合物自由基已为电子自旋共振(ESR)所特征。现已检测和鉴定到二种自旋加合物:一种是叔碳自由基;另一种是仲碳自由基。它们分别是由BP的激发三重态从LDPE链的支化点和亚甲基团上夺氢所形成的自由基中间体同自旋捕捉剂BNB反应生成的。上述的证据表明:LDPE的光引发交联点主要发生在叔碳和仲碳原子上,且H-型交联点占主导地位。     

Γ andX bandgap hydrostatic deformation potentials for epitaxial In0.52Al0.48As on InP(001)

The pressure dependence of the direct and indirect bandgap of epitaxial In_0.52Al_0.48As on InP(001) substrate has been measured using photoluminescence up to 92 kbar hydrostatic pressure. The bandgap changes from Γ toX at an applied pressure of ∼ 43 kbar. Hydrostatic deformation potentials for both the Γ andX bandgaps are deduced, after correcting for the elastic constant (bulk modulus) mismatch between the epilayer and the substrate. For the epilayer we obtain and+(2.81±0.15)eV for the Γ andX bandgaps respectively. From the pressure dependence of the normalized Γ-bandgap photoluminescence intensity a Γ-X lifetime ratio, (τ_Γ/τ _X ), of 4.1×10⁻³ is deduced.     

Pressure and temperature effects on the excess deuteron and proton conductance

The limiting molar conductances ° of deuterium chloride DCl in D₂O were determined as a function of pressure and temperature in order to examine the proton-jump mechanism in detail. The excess deuteron conductances °_E(D ⁺), as estimated by the equation [°_E(D ⁺) = °(DCl/D ₂ O) – °(KCl/D ₂ O)], increases with an increase in the pressure and temperature as well as the excess proton conductance [°_E(H ⁺) = °(HCl/H ₂ O) – °(KCl/H ₂ O)]. The isotope effect on the excess conductances, however, depends on the pressure and temperature contrary to the model proposed by Conway et al.: °_E(H ⁺)/°_E(D ⁺) decreases with increasing pressure and temperature. The magnitude of the decrease with pressure becomes more prominent at lower temperature. These results are discussed in terms of the pre-rotation of adjacent water molecules, the bending of hydrogen bonds with pressure, and the difference in strength of hydrogen bonds between D₂O and H₂O.     

Effect of pressure on the solubilities ofo-,m- andp-xylene in water

The solubilities of o-, m- and p-xylene in water were measured at 25.0°C up to 250, 385, and 50 MPa, respectively. The solubility increased with increasing pressure up to 120 MPa (50 MPa for p-xylene) and then decreased. The reaction volumes, V^o accompanying the dissolution at 0.1 MPa were estimated as –3.6±0.5, –3.4±0.5, and –4.1±0.5 cm³-mol^–1 for o-, m-, and p-xylene, respectively, from the pressure dependences of the solubilities. The limiting partial molar volumes, of p- and o-xylene in water under high pressure were estimated from V^o and the molar volume of the xylene. The partial molar volumes decreased with increasing pressure. The reaction volume for the formation of intra-molecular pairwise hydrophobic interaction between the methyl groups, as proposed by Ben-Naim, is discussed for the V^o of p- and o-xylene at 0.1 MPa.     

Clathrate formation in water-cyclic ether systems at high pressures

Experimental data on the investigation of the water-trimethyleneoxide system,P, t, x phase diagram (up to 6 kbar) are presented. The results are compared with those on water systems with ethyleneoxide, 1,3- and 1,4-dioxane, 1,3-dioxolane and tetrahydrofuran, on the basis of which a summarizedP, t, x diagram is plotted for water-cyclic ether systems. It is shown that in all the systems in which a cubic structure II hydrate forms at 1 bar, it eventually turns to cubic structure I under pressure. The nature of high pressure hydrates is discussed.Dedicated to the memory of D. W. Davidson.     

Characterization of some essential oils and their key components: Thermoanalytical techniques

The present study was aimed at determining the kinetics of evaporation and establishing vapor pressure curves for both single and multi-component systems by thermogravimetry (TG) and differential scanning calorimetry (DSC). Essential oils (e.g. lavender oil, orange oil, clove oil and eucalyptus oil, etc.) are typically multi-component systems consisting of various volatile pure components (e.g. linalyl acetate, limonene, cinnamaldehyde, etc.) which resemble single component systems. In this study linalyl acetate was taken as the calibration compound for TG. The vapor pressure curves for the pure substances were plotted using TG and vapor pressure plots for clove oil and eucalyptus oil were constructed using DSC. The thermodynamic and kinetic parameters of the pure compounds were compared to that of the multi-component systems to quantitatively and qualitatively measure the influence of different compounds on each other. The k-value from the vapor pressure data for linalyl acetate was calculated as 112006 Pa kg^0.5mol^0.5s^-1 m^-2 K^-0.5. The vapor pressure values were used to determine the Antoine constants using the SPSS 10.0 software.This revised version was published online in November 2005 with corrections to the Cover Date.     

New PVC materials for medical applications—the release profile of PVC/polycaprolactone–polycarbonate aged in aqueous environments

Medical grade PVC plasticised with polycaprolactone–polycarbonate (PCL–PC) was subjected to aqueous environments at different temperatures. The release profile during ageing was determined by solid phase microextraction (SPME) and GC–MS. At the same time changes in the surface composition due to, for example, migration of PCL–PC from the blend were followed by FTIR. Almost no changes in the material or its surface composition were observed during 98 days at 37 °C in water or phosphate buffer. Only trace amount of 6-hydroxyhexanoic acid the final hydrolysis product of PCL–PC was detected in the GC–MS chromatograms and the weight loss was negligible. Even when the ageing temperature was raised to 70 °C only minor increase in the amount of 6-hydroxyhexanoic acid was observed and the weight loss after 98 days was under 1%. Changes in the FTIR spectra indicating migration of PCL–PC towards the surface of the PVC/PCL–PC tubing were observed first after 70 days at 70 °C. Large increase in the hydrolysis rate of PCL–PC and almost complete depletion of PCL–PC from the blend was observed when the ageing temperature was raised to 100 °C.     

Development of a new analytical method for the evaluation of hazards from slow decomposition of waste streams and process solutions

A wide variety of liquid streams are generated as part of the process research and development effort. Frequently these streams are drummed off, either as intermediates that must be held for processing or as wastes that must be sent off-site for disposal. Because of the long times and low concentrations often involved, current thermoanalytical techniques were inadequate to detect the potential of streams to generate gas. A custom-made apparatus, the gas evolution test cell (GETC), was developed in the Merck Research Laboratories to measure the gas generation potential of various streams under precisely defined conditions, is the key innovation for the development of a quantitative gas-generation test method.