Structure evolution and mechanical properties enhancement of Al/AlN multilayer

A set of Al/AlN multilayers with various modulation periods were prepared using DC magnetron sputtering method. Low angle X-ray diffraction (LAXRD) was used to analyze the layered structure of multilayers. The phase structure of the films was investigated with grazing angle X-ray diffraction (GAXRD). LAXRD results indicate that well-defined multilayer modulation structures are formed for the relatively larger modulation periods. However, the loss of mutilayered structure is detected in the multilayer with low modulation period. A very wide amorphous peak is observed in multilayer with modulation period of 4 nm. The multilayers show obvious crystallization at larger modulation periods, however, the diffraction peaks are much wider than the Al single layer because of the interruption of the continuous columnar grain growth by alternating deposition processes. Nanoindentation experiments were performed to study the mechanical properties as a function of multilayer modulation period. It is found that the hardness of the multilayers is greater than the hardness calculated from rule of mixtures. With the modulation periods adjusted, the multilayers are even harder than its hard component (AlN). A maximum hardness of 24.9 GPa, about 1.9 times larger than its hard component (AlN) and 3.7 times larger than the hardness calculated from the rule of mixtures, is found at the multilayer with modulation period of 16 nm. The wear test results show that the multilayers possess lower and stable friction coefficient, and superior wear properties.     

橡胶接触轮硬度、槽形和工件硬度对砂带磨削的影响

本文主要研究橡胶接融轮硬度、槽形和工件硬度对金属切除量、砂带磨损、磨削比、磨削力 和工件表面粗糙度的影响，它对砂带磨削时根据不同的工件硬度、不同的技术要求正确选用橡胶接触轮的硬度和槽形提供了依据．     

填料对软质聚氯乙烯硬度及力学性能的影响

研究了滑石粉和炭黑对软质聚氯乙烯的硬度及其温度依赖性和力学性能的影响，并将它们同ＡＢＳ和ＭＢＳ进行了比较，高度填充和适当的滑石粉／炭黑组合能提高软质ＰＶＣ的硬度和降低硬度对温度的依赖性，并使材料保持较好的力学性能和低温柔性。     

Effect of pearlitic morphology with varying fineness on the cavitation erosion behavior of eutectoid rail steel

The present work discusses the effect of the pearlitic morphology with varying fineness on the cavitation erosion behavior of eutectoid rail steel. Cavitation erosion of three different types of the pearlitic steels (furnace-cooled, air-cooled, and forced-air-cooled) consisting of coarse, fine, and very fine microstructures were tested in 3.5% NaCl solution and compared with that of the as-received pearlitic rail steel. The variation in the mean depth of erosion (MDE) and mean depth erosion rate (MDER) with erosion time was analyzed. Furthermore, the cavitation erosion resistance of the as-received, the air-cooled, and the forced-air-cooled was found to be 1.03, 1.51, and 2.14 times better than the furnace-cooled pearlitic steel, respectively. It was concluded that the cavitation erosion resistance of the pearlitic steel increased with the increase in the fineness of the microstructure.     

Determination of mechanical properties by instrumented indentation

The paper reviews the current state of the depth-sensing indentation (sometimes called nanoindentation), where the information on material behaviour and properties is obtained from the indenter load and depth, measured continuously during loading and unloading. It is shown how the contact parameters and principal characteristics are determined using pointed or spherical indenters. Indentation tests can be used for the measurement of hardness and elastic modulus, and also of the yield stress and for the construction of stress–strain diagrams, for the determination of the work of indentation and its components. Most devices use monotonic loading and unloading, but some also enable measurement under a small harmonic signal added to the basic monotonously increasing load. This makes possible continuous measurement of contact stiffness and the study of dynamic properties and the determination of properties of coatings. One section is devoted to the measurement on viscoelastic-plastic materials, where the delayed deforming must be considered during the measurement as well as in data evaluation. Instrumented indentation can also be used for the study of creep under high temperatures. The paper also discusses the errors arising in depth-sensing measurements and informs briefly about some other possibilities of the method.     

Crystal growth and dielectric, mechanical, electrical and ferroelectric characterization of n-bromo succinimide doped triglycine sulphate crystals

Single crystals of triglycine sulphate (TGS) doped with n-bromo succinimide (NBS) were grown at ambient temperature by the slow evaporation technique. An aqueous solution containing 1-20 mol% of n-bromo succinimide as dopant was used for the growth of NBSTGS crystals. The incorporation of NBS in TGS crystals has been qualitatively confirmed by FTIR spectral data. The effect of the dopant on morphology and crystal properties was investigated. The cell parameters of the doped crystal were determined by the powder X-ray diffraction technique. The dielectric constant of NBS doped TGS crystal was calculated along the ferroelectric direction over the temperature range of 30-60 °C. The dielectric constant of NBSTGS crystals decrease with the increase in NBS concentration and considerable shift in the phase transition temperature (T_C) towards the higher temperature observed. Pyroelectric studies on doped TGS were carried out to determine the pyroelectric coefficient. The emergence of internal bias field due to doping was studied by collecting P-E hysteresis data. Temperature dependence of DC conductivity of the doped crystals was studied and gradual increase in the conductivity with the increase of dopant concentration was observed. The activation energy (ΔE) calculated was found to be lower in both the ferroelectric and the paraelectric phases for doped crystals compared to that of pure TGS. The micro-hardness studies were carried out at room temperature on thin plates cut perpendicular to the b-axis. Less doped TGS crystals show higher hardness values compared to pure TGS. Piezoelectric measurements were also carried out on 010 plates of doped TGS crystals at room temperature.     

Laser carbonitriding of alumina surface

Laser carbonitriding of alumina surfaces is examined. Temperature and stress fields developed during the laser heating of the substrate surface are predicted using the finite element method in line with the experimental conditions. The formation of Al(C, N) and AlN compounds in the surface region of irradiated workpiece is examined using X-ray Photoelectron Spectroscopy (XPS) and X-ray Diffraction (XRD). The microstructural and morphological changes in the laser irradiated region are examined using Scanning Electron Microscope (SEM). The microhardness of the resulting surface is measured and compared with the base material hardness. It is found that high temperature gradient is developed in the irradiated region, which in turn, results in high residual stress levels in this region. XPS and XRD data reveal the presence of Al (C, N) and AlN compounds in the surface region. The microhardness in the surface region of the laser treated workpiece increases significantly.     

Influence of Ti/TiAlN-multilayer designs on their residual stresses and mechanical properties

In this research work, Ti/TiAlN multilayers of various designs were deposited onto substrates pretreated by different etching procedures. The influence of multilayer design and substrate pretreatment on multilayers adhesion, hardness, wear and friction coefficients was systematically analyzed and correlated with residual stresses of these multilayers as well as with residual stresses on the coating-near substrate region, which were analyzed by synchrotron X-ray diffraction at HZB-BESSYII. These investigations show that the adhesion can be improved by a specific etching procedure, which cause increased compressive stress in the coating-near the substrate region. Additionally, it was found, that the multilayer with the thickest ceramic layers has the highest hardness and the lowest wear coefficients as well as the lowest compressive residual stress within studied multilayers.     

Preparation of a novel Ni/Co-based alloy gradient coating on surface of the crystallizer copper alloy by laser

A high wear-resistant gradient coating made of Ni/Co-based alloys on the surface of a Cu alloy substrate was synthesized using a YAG laser induced in situ reaction method. The coating consists of three layers: the first is a Ni-based alloy layer, the second and third are Co-based alloy layers. The microhardness increases gradually from 98 HV in the Cu alloy substrate to the highest level of 876 HV in the third layer. The main phase of the Co-based alloy layer is CoCr₂(Ni,O)₄, coexisting with the Fe₁₃Mo₂B₅, Cr(Co(Mo, and FeCr_0.29Ni_0.16C_0.06 phases. Wear tests indicate that the gradient coating has good bond strength and wear properties with a wear coefficient of 0.31 (0.50 for the Cu alloy substrate). Also, the wear loss of the coating is only 0.01 g after it has been abraded for 60 min, which is only one fifth of that of the Cu alloy of the crystallizer. Wear tests of the gradient coating reveal good adhesive friction and wear properties when sliding against steel under dry conditions. This novel technique may have good application to make an advanced coating on the surface of the Cu alloy crystallizer in a continuous casting process.