Impedance and dielectric studies of ferroelectric SrBi2Nb2O9 ceramics

This paper reports the dielectric and impedance characteristics of ferroelectric SrBi₂Nb₂O₉ (SBN) ceramics in the 100 Hz-1 MHz frequency range at various temperatures (300-823 K). A strong low frequency dielectric dispersion (LFDD) associated with an impedance relaxation has been found to exist in these ceramics in the temperature range 573-823 K. The Z″ of the AC complex impedance showed two distinct slopes in the frequency range 100 Hz-1 MHz suggesting the existence of two dispersion mechanisms. This non-ideal behavior has been explained on the basis of the expression, Z*=R₀/(1+(iω/ω₁)^m+(iω/ω₂)ⁿ) [J. Phys. Chem. Solids 53 (1992) 1] where ω₁ and ω₂ characterize the lattice response and the charge carrier behavior, respectively. The exponents m and n were obtained from the curve fitting. The exponent n was found to exhibit a minimum at the Curie temperature, T_c (723 K) whereas the m was temperature independent.     

Mechanical Properties of Blends of Low-Density Polyethylene with Chlorinated Polyethylene

The results of experimental investigation into the mechanical properties of blends of low-density polyethylene (LDPE) with chlorinated polyethylene (CPE) in tension are presented. The specimens of pure LDPE, CPE, and nine types of LDPE/CPE blends, with different content of components at 10 wt.% intervals, were examined. Data on the influence of blend composition on the tensile stress-strain diagram, elastic modulus, yield stress, breaking stress, and ultimate elongation are obtained. The results of investigations of creep are also reported. It is found that the creep compliance (the total current compliance minus the elastic compliance) obeys the power law of creep.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 391–404, May–June, 2005.     

Über die Magnetischen Eigenschaften der Cobaltate Na6CoS4, Na6CoSe4 und K6CoS4

Magnetic Properties of the Cobaltates Na₆CoS₄, Na₆CoSe₄, and K₆CoS₄ The alkali metal cobalt chalcogenides Na₆CoS₄, Na₆CoSe₄, and K₆CoS₄ crystallize in the space group P6₃mc with Z = 4. The structure is characterized by isolated [CoX₄]-tetrahedra. The magnetic susceptibilities show Curie-Weiss behaviour. The deviations at low temperatures are caused by antiferromagnetic interactions. The magnetic moments are discussed with regard to ligand-field parameters.     

STUDY ON POLYPYRROLE-VISCOSE CONDUCTING FIBER

The conductivity of Polypyrrole-viscose conducting fiber prepared with author's method can be shown up to as high as 2.106x10~(-2) S/cm. The main factors influencing the conductivity are the concentration of FeCl_3 used as dopant and initiator, the treatment time of viscose fiber as base material in FeCl_3 solution, temperature and polymerization time. It is found that the orientation and crystallization degree of viscose fiber keep constant before and after conducting treatment and the mechanical properties of conducting fiber is the same as that of base material. In addition, the distribution of polypyrrole in viscose fiber, and its effect on the conductivity were investigated in details by TEM.     

Chalcogenide based all-solid-state thin electroplated ion-selective membrane for Hg(II) flow-injection determinations

The response to Hg(II) of a thin all-solid-state Te-doped silver chalcogenide membrane, described by the general formula Ag₂ + δSe_{1 − x}Te_x, which has been electrochemically prepared following a previously proposed approach, has been investigated. The kinetics of formation of the membrane's secondary dynamic response to Hg(II) has been successfully combined with the precise timing and transient signal, typical for flow-injection (FI) measurements, in developing a sensitive and reliable mercury FI detector. Under optimized stream conditions it exhibits a linear Nernstian response, with a double slope of the calibration graph of 59 mV dec⁻¹, over the mercury(II) concentration range 10⁻⁶ − 10⁻³ M, the typical sample throughput amounting to about 70 samples per hour. The observed chemical amplification of the signal is due to the specificity of the processes dominating the initial step in formation of the steady-state signal of the membrane to mercury. The analytical performance of the Hg(II) FI detector, as regards sensitivity, reproducibility, selectivity and long-term stability has been thoroughly investigated. The exact procedure for membrane electrodeposition is given and the potential of the proposed approach as a cost-effective way for preparing chalcogenides of unique structure and properties has been outlined in the above context.     

Flow-injection determination of 3-hdroxybutyrate in serum with an immobilized 3-hydroxybutyrate dehydrogenase reactor and chemiluminescence detection

A flow-injection system for the determination of 3-hydroxybutyrate in serum is described. 3-Hydroxybutyrate dehydrogenase is immobilized on poly(vinyl alcohol) beads and incorporated in a flow-injection system. 1-Methoxy-5-methylphenazinium methylsulphate reacts with enzymatically generated NADH to give H₂O₂, which is detected chemiluminometrically with the reaction of luminol and hexacynoferrate(III). Serum is diluted and filtered through an ultrafiltration membrane. The system responds linearly to injected samples (80 μl) in the concentration range 0.5–300 μM; the detection limit is 0.1 μM. The within-day relative standard deviation (n = 90) for 58 μM 3-hydroxybutyrate in serum is 0.8%. The maximum throughout is 20 samples per hour. The immobilized enzyme is stable for at least 1 month.     

Chemical synthesis and electric properties of the conducting copolymer of aniline and o‐aminophenol

A copolymer, poly(aniline‐co‐o‐aminophenol), was prepared chemically by using ammonium peroxydisulfate as an oxidant. The monomer concentration ratio of o‐aminophenol to aniline strongly influences the copolymerization rate and properties of the copolymer. The optimum composition of a mixture for the chemical copolymerization consisted of 0.3 M aniline, 0.021 M o‐aminophenol, 0.42 M ammonium peroxydisulfate, and 2 M H₂SO₄. The result of cyclic voltammograms in a potential region of ?0.20 to 0.80 V (vs.SCE) indicates that the electrochemical activity of the copolymer prepared under the optimum condition is similar to that of polyaniline in more acid solutions. However, the copolymer still holds the good electrochemical activity until pH 11.0. Therefore, the pH dependence of the electrochemical property of the copolymer is improved, compared with poly(aniline‐co‐o‐aminophenol) prepared electrochemically, and is much better than that of polyaniline. The spectra of IR and ¹H NMR confirm that o‐aminophenol units are included in the copolymer chain, which play a key role in extending the usable pH region of the copolymer. The visible spectra of the copolymers show that a high concentration ratio of o‐aminophenol to aniline in a mixture inhibits the chain growth. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5573–5582, 2007     

Effective-Field Theory on High Spin Systems with Biaxial Crystal Field

Based on the effective-field theory with self-spin correlations and the differential operator technique,physical properties of the spin-2 system with biaxial crystal field on the simple cubic, body-centered cubic, as well as faced-centered lattice have been studied. The influences of the external longitudinal magnetic field on the magnetization,internal energy, specific heat, and susceptibility have been discussed in detail. The phenomenon that the magnetization in the ground state shows quantum effects produced by the biaxial transverse crystal field has been found.     

Structural and magnetic properties of RF sputtered FePt/Fe multilayers

Series of [FePt(4min)/Fe(t_Fe)]₁₀ multilayers have been prepared by RF magnetron sputtering and post-annealing in order to optimize their magnetic properties by structural designs. The structure, surface morphology, composition and magnetic properties of the deposited films have been characterized by X-ray diffractometer (XRD), Rutherford backscattering (RBS), scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDX) and vibrating sample magnetometer (VSM). It is found that after annealing at temperatures above 500 °C, FePt phase undergoes a phase transition from disordered FCC to ordered FCT structure, and becomes a hard magnetic phase. X-ray diffraction studies on the series of [FePt/Fe]_n multilayer with varying Fe layer thickness annealed at 500 and 600 °C show that lattice constants change with Fe layer thickness and annealing temperature. Both lattice constants a and c are smaller than those of standard ones, and lattice constant a decreases as Fe layer deposition time increases. Only a slight increase in grain size was observed as Fe layer decreased in samples annealed at 500 °C. However, the increase in grain size is large in samples annealed at 600 °C. The coercivities of [FePt/Fe]_n multilayers decrease with Fe layer deposition time, and the energy product (BH)_max reaches a maximum in the samples with Fe layer deposition time of 3 min. Comparison of magnetic properties with structure showed an almost linear relationship between the lattice constant a and the coercivities of the FePt phase.     

Two-dimensional numerical calculation of the flow field about a scoop inlet by the piecewise linear method

The piecewise linear method (PLM) based on time operator splitting is used to solve the unsteady compressible Euler equations describing the two-dimensional flow around and through a straight wall inlet placed stationary in a rapidly rotating supersonic flow. The PLM scheme is formulated as a Lagrangian step followed by an Eulerian remap. The inhomogeneous terms in the Euler equations written in cylindrical coordinates are first removed by Sod's method and the resulting set of equations is further reduced to two sets of one-dimensional Lagrangian equations, using time operator splitting. The numerically generated flow fields are presented for different values of the back pressure imposed at the downstream exit of the inlet nozzle. An oblique shock wave is formed in front of the almost whole portion of the inlet entrance, the incoming streamlines being deflected towards the higher pressure side after passing through the oblique shock wave and then bending down to the lower pressure side. A reverse flow appears inside the inlet nozzle owing to the recovery pressure of the incoming streams being lower than the back pressure of the inlet nozzle.