Degradation of Mater-Bi/wood flour biocomposites in active sewage sludge

The mechanical properties of Mater-Bi^® are, in general, not adequate for certain applications and the addition of a filler is therefore necessary. Among the different fillers, natural fibres are particularly interesting because they potentially allow improving the performance of the material without compromising its biodegradability.In order to improve the basic mechanical properties of a Mater-Bi grade and to obtain a new, fully biodegradable material, wood flour based composites were prepared by different processing methods. To simulate actual and not laboratory bacterial attack on the prepared materials, in this work we studied the biodegradation of the composites in a real active sewage sludge reactor. In particular, the biodegradation rates were investigated with reference to different pre-treatments of the materials and different environmental conditions (summer and winter). The results showed that wood flour enhances the biodegradability of the materials. The results indicated also strong relationships between the surface roughness and the biodegradation rates (in particular, higher roughness leads to wider bacterial attack). The different processing techniques had direct effects on the overall biodegradation rates. In particular, when higher smoothness and packing is achieved, the biodegradation rate is lower. The mechanical analysis indicated that adding wood flour to Mater-Bi has positive effects on the elastic modulus, but when the bacterial attack becomes critical, a general sudden drop of the mechanical properties is observed.     

Study on photodegradation of injection-moulded β-polypropylenes

The effects of UV irradiation on β-nucleated injection-moulded polypropylenes (β-iPP) have been studied at several structural levels. Commercially available isotactic polypropylene was modified by 0.03 wt.% β-nucleating agent based on N,N′-dicyclohexylnaphthalene-2,6-dicarboxamide. β-iPP specimens were injection-moulded using a processing set-up in which only mould temperature was varied. It was found that specimens consisted of a skin-core structure, which was strongly influenced by varying mould temperatures. The structural development consequently affected the specimen degradability as shown by wide-angle X-ray scattering, light microscopy and micro-infrared microscopy.     

基于PROFIBUS注塑车间分布式监控系统的研究

随着塑料产品产量的增加,许多企业都建有一定规模的注塑车间.对车间内的注塑机进行有效的计算机监控管理,能及时掌握注塑机的运行状况,提高生产效率,提升企业信息化程度.采用一种基于PROFIBUS现场的总线技术,给出了注塑车间分布式监控系统的硬件组成原理、监控系统的功能及系统组态的实现,该系统可同时对多台注塑机进行现场及远程监控.     

An inverse finite element method with an application to extrusion with solidification

The flow and solidification of planar jets are analysed by means of an efficient inverse isotherm finite element method. The method is based on a tessellation that is constructed by isotherms as characteristic co-ordinate lines transverse to the flow direction. Thus opposite sides of finite elements lie on isotherms. The method allows the simultaneous determination of the location of the isotherms with the primary unknowns, namely, the velocity, the pressure, the temperature and the location of the free surface. Thus the determination of the location of the solidification front (which is known to pose significant computational difficulties) is automatic. This facilitates the control of the location of the solidification front by controlling macroscopic variables such as the flow rate, the cooling rate and the capillary design. The location of the solidification may then be suitably chosen to influence the frozen-in orientation and structure in extrusion of high-performance materials such as composites and polymers, in continuous casting of metals and in growth of crystals.     

Transient finite element method for calculating steady state three-dimensional free surfaces

In order to reduce the cost of large three-dimensional calculations of steady state free surfaces, we have combined a time-dependent approach, a decoupling algorithm and a conjugate gradient solver along the lines introduced earlier by Gresho and Chan. The free surface is calculated separately by applying the kinematic condition to a number of faces defined on the undeformed surface. For the pseudo-time-marching technique we show that it is economical to adopt different time steps for the free surface calculation and the other fields. The accuracy of the method is tested on the well-known circular die problem; the method is then used to reveal the effects of inertia and shear thinning on square and rectangular dies.     

Study on Injection Moulding of High Precision Aspheric Plastic Lens

With the rapid development of information and multi me dia technologies, the demand for the optical plastic aspheric elements used in o pto-electronic devices, camera, optical disc and projector lens etc. has been i ncreased rapidly in the recent years. The key technologies of fabrication of asp heric plastic lens are the design and manufacturing moulds, selection of proper injection moulding equipment, and optimization of injection moulding parameters etc. In this paper, the effect of injection pressure,...     

注塑件质量分析

本文就游戏机盖和不倒翁玩具底座为例,分析注塑件的质量和改进途径.     

先进陶瓷的精密注射成型

讨论了陶瓷粉末注射成型制备精密陶瓷部件这一新技术及其国内外发展状况.先进陶瓷精密注射成型的科学基础是现代高分子精密注塑理论和现代陶瓷制造技术,它将高分子流变学、陶瓷粉体技术、陶瓷工艺学和金属模具精密制造技术结合在一起.该技术突出的优点有:①可净近成型各种复杂形状的陶瓷零部件,使烧结后的陶瓷产品无需进行机加工或少加工,从而减少昂贵的陶瓷成本;②成型制品具有极高的尺寸精度和表面光洁度;③可实现微成型(M icro In jection Mold ing),制备μm~mm范围内的微型陶瓷零件;④成型过程机械化和自动化程度高,重复性好,便于规模化低成本生产.该技术已用于陶瓷发动机、通讯产业中光纤连接器陶瓷插芯(Ferru le)、计算机工业中光盘和磁盘驱动用陶瓷轴承和生物医学用陶瓷制品等精密陶瓷件的制造.随着微注射成型新技术的发展,微型陶瓷部件将应用于环境要求苛刻、结构复杂的MEMS系统.     

集成化商业 CAD 系统的实现技术

介绍了商业ＣＡＤ系统中的造型技术,商场布置技术和效果图生成技术,其中着重阐述了参数造型技术,商场布置技术,真实感图形生成算法和图象叠加算法．