Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

Photooxidation of aqueous trichloroethylene using a buoyant photocatalyst with reaction progress monitored via micro-headspace GC/MS

Although photooxidation has previously been shown to be successful in removing organic contaminants from water, methods combining the rapid photooxidation of the desired contaminant with easy catalyst manipulation and removal are few and far between. In the absence of an easy means of catalyst removal, the photooxidation process becomes more costly and time consuming, and photocatalysis cannot be employed as an in situ method for the remediation of aqueous organic contaminants. In this study, the photocatalyst was added to an aqueous trichloroethylene (TCE) solution in the form of TiO₂-coated buoyant microspheres. The solution, placed in a flow-cell photoreactor along with the buoyant catalyst, was irradiated with a UV-filtered Xenon light source. Limited sample sizes necessitated the development of a low-cost headspace GC/MS analysis method, utilizing a standard direct-injection autosampler. This analytical technique aptly monitored reaction progress and indicated that aqueous TCE concentration decreases by nearly 90% in the first hour of irradiation. Subsequent solvent extraction GC/MS analysis indicated that the TCE is initially sorbed by the photocatalyst spheres, but as irradiation continued, TCE is removed from the catalyst spheres surfaces. During the course of irradiation, the expected TCE mineralization product hydrochloric acid appeared, as indicated by a decrease in pH and ion chromatography analysis. The microsphere-born catalyst was easily removed from the treated solution by filtration. Thus, it is possible that a method for effective, low-cost in situ photooxidation of aqueous organic contaminants will be realized in the near future.     

鲤鱼体中鱼腥味物质的提取和鉴定

采用同时蒸馏萃取法提取鲤鱼鱼体中的挥发和半挥发性有机物，用GC／MS从提取物中分析鉴定出鱼腥味和疑是鱼腥味物质16种。包括醛、烯醛、酮和呋喃4类化合物。其中己醛、庚醛和2，4-二烯癸醛被确认为鱼腥味的化合物。研究发现，这些物质总量在鲤鱼体的鱼鳞、鱼鳃和鱼肉的分布呈现下降趋势，且其总量与鱼腥味强度之间具有可比较的对应关系。     

Fe_3Al的抗高温氧化和耐热腐蚀性能

在７００℃与８５０℃的高温下，Ｆｅ＿３Ａｌ金属间化合物表面形成了Ａｌ＿２Ｏ＿３保护膜，使其抗氧化性能远优于不妨钢，２％Ｃｒ（原子百分比）加入Ｆｅ＿３Ａｌ会导致氧化过程初期氧化速率的增高，在熔融的硫酸盐和高压锅炉的烟气中，Ｆｅ＿３Ａｌ的耐热腐蚀性能优于高温合金ＧＨ１３２．     

专家系统技术在注塑模故障诊断中的应用

论述了用人工智能技术对模具故障进行诊断和确定对策的原理和方法。对模具在工作中常遇到的与模具制造、工艺条件及塑料材料有关的问题及相应对策进行了归纳整理，组成了模具诊断与维修知识库。收集了常用工程塑料的各种有关成型工艺条件和主要性能，建立了塑料材料数据库。采用正向推理控制策略搜索知识库，并将推理结果与理论计算结果进行对比校验，最后确定出模具工作中出现故障的原因，并输出相应的解决办法和建议．     

示差半微分循环伏安法研究琥珀酰胆碱在水/硝基苯界面的传递行为

研究了油/水界面电解的示差半微分循环伏安行为。在0.01mol/L LiCl(w)-0.01mol/L TBATCIPB(nb)体系“电位窗”比TBATPB(nb)向正方向扩展约50mV,残余电流基本消除,使“电位窗”内的平台向左右拓宽约50mV。算得界面电容约为16μF/cm~2。考察了琥珀酰胆碱离子在w/nb界面的传递伏安特性,结果与一般半微分循环伏安法相似。但峰形改善,检测限降低一个数量级(1×10~(-6)mol/L),相对标准偏差在5％以内,可用于定量测定琥珀酰胆碱。     

含有纯滞后对象的控制方法

评述纯滞后对象控制的两种典型方法─—大林算法和纯滞后补偿法的原理、优缺点、设计要求及存在问题，并讨论了两者的联系。     

钢液定氧测头响应时间和热平衡态

本文分别研究了ＺｒＯ２（ＭｇＯ）固体电解质管头壁厚，参比电极量对定氧测头响应时间的影响，得出了以ＺｒＯ２管头壁厚为０．６０－０．８０ｍｍ，Ｃｒ／Ｃｒ２Ｏ３参比电极加入量为４０－６０ｍｇ所组成的定氧测头响应速度最快，同时采用了“双偶法”对定氧测头在工作过程中的热平衡态进行了研究。结果表明：氧浓差电池中的传热是响应过程的控速步骤，氧电势曲线上峰值的产生是起源于电池中的热平衡态。