钢桥面板顶板与纵肋连接疲劳开裂局部加固分析

正交异性钢桥面板纵肋与顶板连接细节处极易产生疲劳裂纹.本文通过精细化有限元模型,分析了栓接角钢加固法和粘贴纤维增强复合材料(Fiber Reinforced Polymer, FRP)型材加固法对钢桥面板疲劳性能的影响.结果表明:采用角钢、FRP型材对顶板与纵肋连接细节的疲劳裂纹进行加固,焊缝裂纹附近热点应力峰值降幅可达56.2%和46.5%;焊缝裂纹尖端附近应力强度因子随着板件整体尺寸的增大而减小;改变板件厚度对应力强度因子结果值影响最大,最高可使其下降约80%,改变板件纵向长度和单肢长度对其有一定影响;随着裂纹的持续扩展,栓接角钢法的加固效果开始下降.建议在监测到构造细节处疲劳裂纹后应尽早加固.     

Adsorption and inhibitive properties of aminobiphenyl and its Schiff base on mild steel corrosion in 0.5 M HCl medium

Electrochemical measurements were performed to investigate the effectiveness and adsorption behaviour of aminobiphenyl (Aph) and 2-(3-hydroxybenzylideneamino)biphenyl (Aph-S), as corrosion inhibitors for mild steel (MS) in 0.5 M HCl solution. Potentiodynamic polarization, linear polarization resistance (LP) and electrochemical impedance spectroscopy (EIS) techniques were applied to study the metal corrosion behaviour in the absence and presence of different concentrations of Aph and Aph-S. In order to gain more information about adsorption mechanism the AC impedance technique was used to evaluate the potential of zero charge (PZC) from polarization resistance (R_p) versus voltage (E) plot. Potentiodynamic polarization measurements showed that Aph act as cathodic type inhibitor where as Aph-S act mixed type. The inhibition efficiency (IE%) increases with increasing concentration of compounds and reached 92.6% for Aph and 97.2% for Aph-S at 5 × 10⁻³ M. Double layer capacitance (C_dl) and polarization resistance (R_p) values are derived from Nyquist plots obtained from AC impedance studies. The experimental data fit Langmuir isotherm for both Aph and Aph-S, and from the adsorption isotherm some thermodynamic data for the adsorption processes are calculated and discussed. The effect of exposure time on the corrosion behaviour of mild steel in the absence and presence of inhibitor over 168 h was also studied.     

Corrosion prevention of mild steel in acidic medium by 2-Pyrrolidin-1-yl-1,3-thiazole-5-carboxylic acid: Theoretical and experimental approach

The inhibition efficiency of 2-Pyrrolidin-1-yl-1,3-thiazole-5-carboxylic acid (PTCA) against mild steel (MS) corrosion was investigated in acidic solution by using quantum chemical calculations based on Density Functional Theory (DFT) method and electrochemical measurements. The electrochemical impedance spectroscopy (EIS), potentiodynamic, potential zero charge (pzc) analysis and electrochemical noise (EN) measurements at various concentrations (from 0.1 to 10 mM) and immersion times were utilized in experimental part. The surface analysis was achieved scanning electron microscope (SEM) and contact angle measurements in the absence and presence of 10 mM PTCA. According to DFT results, PTCA exhibited 3.737 eV band gap and 8.130 Debye dipole moment which were a signal of potentially convenient corrosion inhibitor properties. PTCA has a remarkable corrosion inhibition capability to mild steel, which inhibited both anodic and cathodic corrosion rates, relying on it's physically adsorption on the metal solution interface and protection ability was increased with increasing PTCA concentration. The obtained adsorption equilibrium constant was 11.11 × 10³ M^-1 and calculated standard free energy of adsorption was ?33.03 kJ mol^?1. The determined activation energy values were 55.58 kJ mol^?1 and 96.86 kJ mol^?1 in 0.5 M HCl in the absence and presence of 10 mM PTCA, respectively. PTCA demonstrated a strong inhibition efficiency of 98.3%, after 168 h immersion, according to the EIS results. As a consequently, we recommend that PTCA is a convenient inhibitor in 0.1 M HCl for mild steel protection against corrosion.     

Investigation of bio-corrosion in galvanized steel by Desulfovibrio desulfuricans and its mitigation by Butea monosperma leaf extract as green inhibitor

This work is intended to examine the microbially influenced corrosion on galvanized steel (GS) caused by sulfate-reducing bacteria (SRB). The efficacy of Butea monosperma (palash) leaf extract to mitigate the corrosion caused by Desulfovibrio desulfuricans was investigated in modified Barr's medium. Weight loss and electrochemical analysis were performed to check the corrosion rate at regular time intervals. SEM images were performed to understand the level of deterioration of the metal surfaces. Image analysis of the unprotected sample showed the presence of pits. From the gravimetric study, the maximum inhibition efficiency (IE) of 98% was obtained with 500 ppm of Palash leaf extract for the fourth-week sample. With the addition of 500 ppm of palash extract, the sulfide concentration decreases to 0 ppm from 123 ppm. Outcomes of potentiodynamic polarization (PP) studies showed that the extract disturbs the cathodic reaction significantly and moves the corrosion potential to a more negative value and IE was about 71% from PP studies. FTIR and GC-MS analysis was performed to recognize the plausible chemical compounds present in Palash leaf powder. EIS results confirmed that the resistance to corrosion increases substantially with the addition of inhibitor. The mechanism for corrosion inhibition has been proposed based on the results obtained.     

Interactions and corrosion mitigation prospective of pyrazole derivative on mild steel in HCl environment

The effectiveness of 1H?pyrazole?3,5?dicarboxylic acid 5?benzyl ester 3?phenyl ester (PCBPE) as a preventer for deterioration of IS 513 Gr. D steel in 1 M HCl medium is evaluated via weight loss, electrochemical impedance, and polarization techniques. Kinetic and thermodynamic parameters assessed the feasibility of the adsorption process at diverse temperatures. The inhibition action on mild steel has been enhanced with increasing PCBPE concentration. It is found from the polarization studies that PCBPE behaves as mixed type inhibitor in HCl medium. The adsorption process of PCBPE on mild steel surface from acid environment is favoured Langmuir adsorption isotherm. The shielding efficiency of PCBPE has been enhanced at elevated concentrations, and it has been diminished at amplified temperatures. The Atomic Force Microscope (AFM), Scanning Electron Microscope (SEM), and Energy Dispersive Spectrum (EDS) were used to establish a surface characterization of metal specimens. A quantum chemical analysis of electron density distributions in the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) demonstrated how the inhibitor undergoes adsorption on mild steel in 1 M HCl. All experimental findings substantiate the corrosion mitigation performance of PCBPE on mild steel in acidic environments.     

A combined computational & electrochemical exploration of the Ammi visnaga L. extract as a green corrosion inhibitor for carbon steel in HCl solution

Natural-based corrosion inhibitors have gained great research interest thanks to their low cost and higher performance. In this work, the chemical composition of the methanolic extract of Ammi visnaga umbels (AVU) was evaluated by gas chromatography (GC) coupled with mass spectrometry (MS) and applied for corrosion inhibition of carbon steel (CS) in 1.0 mol/L HCl using chemical and electrochemical techniques along with scanning electron microscope (SEM) and theoretical calculations. A total of 46 compounds were identified, representing 89.89% of the overall chemical composition of AVU extract, including Edulisin III (72.88%), Binapacryl (4.32%), Khellin (1.97%), and Visnagin (1.65%). Chemical (Weight loss) and electrochemical (potentiodynamic polarization curves (PPC), and electrochemical impedance spectroscopy (EIS)) techniques revealed that investigated extract can be used as an effective corrosion inhibitor for carbon steel in 1.0 mol/L HCl solution. At a low dose of 700 ppm, the inhibitory action of AVU extract reached an inhibition efficiency of 84 percent. According to polarization tests, the investigated extract worked as a mixed inhibitor, protecting cathodic and anodic corrosion reactions. The EIS test showed that upon the addition of AVU extract to HCl solution, the polarization resistance increased while the double layer decreased. SEM images showed a protected CS surface in the inhibited solution. Quantum chemical calculations by Density Functional Theory (DFT) for the main components confirmed the major role of heteroatoms and aromatic rings as adsorption sites. Molecular dynamics (MD) simulation was used to study the adsorption configuration of the main components on the Fe(1 1 0) surface. Outcomes from this study further confirmed the significant advantage of using plant-based corrosion inhibitors for protecting metals and alloys.     

Investigation on corrosion inhibition and adsorption mechanism of azomethine derivatives at mild steel/0.5 ​M ​H2SO4 solution interface: Gravimetric,electrochemical, SEM and EDX studies

The inhibition performance of five azomethine derivatives such as: 1-(4-Methyloxy phenylimino)-1-(phenylhydrazono)-propan-2-one (SB₁), 1-(4-Methylphenylimino)-1-(phenylhydrazono) propan-2-one (SB₂), 1-(phenylimino)-1(phenylhydrazono)-propan-2-one (SB₃), 1-(4-Bromo phenylimino)-1(phenylhydrazono)-propan-2-one (SB₄) and 1-(4-Chlorophenylimino)-1(phenylhydrazono) -propan-2-on (SB₅) as corrosion inhibitors for mild steel in sulfuric acid 0.5 ?M were investigated using different methods. All experimental results demonstrate that these compounds are eficients inhibitors. The inhibition efficiencies ($IE$) increase with inhibitors concentration. At 7.5 $\times$ 10^?5 ?M, the $IE$ was 97.27%, 96.31%, 94.23%, 93.19 and 91.64% for SB₁, SB₂, SB₃, SB₄ and SB₅, respectively. The potentiodynamic polarization results indicated that all the studied inhibitors act as mixed type. The adsorption process on mild steel surface obeyed Langmuir isotherm. The associated activation parameters and thermodynamic have been calculated and discussed. The adsorbed film formed on the metal surface was characterized by SEM and EDX.     

Fire retarded polyurethane foam composites based on steel slag/ammonium polyphosphate system: A novel strategy for utilization of metallurgical solid waste

A series of FR-RPUF composites were prepared by a one-step water foaming process with ammonium polyphosphate (APP) and steel slag (SS) as flame retardants. Thermogravimetric analysis (TG), limiting oxygen index (LOI), UL-94 vertical combustion test, microscale combustion calorimetry (MCC), TG-Fourier transform infrared spectrometry (TG-FTIR), scanning electron microscopy (SEM), Raman spectra and FTIR were used to investigate the thermal stability, flame retardancy, combustion performance, gas phase products, and char residue morphology of FR-RPUF composites. TG test results showed that the initial decomposition temperature (T_-5wt%) and char residue rate at 700°C of RPUF/APP/SS composites were significantly enhanced by the addition of APP and SS, and the thermal stability of the composites was improved. Flame retardant test results confirmed the significantly increased LOI values of RPUF/APP/SS composites with V-0 rating. TG-FTIR also confirmed the obviously decreased release of toxic gases and flammable gases in the combustion of RPUF/APP/SS composites. SEM and Raman spectra of char residues for the composites suggested that APP/SS system improved the compactness and graphitization degree of char layer for RPUF/APP/SS composite. The above researches provide a new strategy for the utilization of SS in fire safety engineering.     

RP-HPLC study of redox equilibria in vanadium-PAR binary and ternary systems: Direct determination of vanadium in steel

The reversed-phase high-performance liquid Chromatographic (RP-HPLC) behaviour of the binary chelates of V(V) and V(IV) with 4-(2-pyridylazo) resorcinol (PAR) and ternary chelates of vanadium with PAR and auxiliary ligands: hydrogen peroxide, hydroxylamine, tartrate and citrate were studied using a C₁₈ column. The complex double-peak chromatograms of V(IV)/V(V)-PAR systems were studied and the origin of each peak was proved. Vanadium in ternary systems with PAR and hydrogen peroxide was found exclusively in V(V)-H₂O₂-PAR complex (single peak on the chromatogram) despite its initial oxidation state. The double role of hydroxylamine (complex agent and reductor) in vanadium systems with PAR was confirmed: in the V(V) system three species were identified (V(V)-PAR, V(V)-NH₂OH-PAR and V(IV)-PAR), but in the V(IV) system only two: V(IV)-PAR and V(V)-NH₂OH-PAR. Citrate and tartrate giving single peak were found as auxiliary ligands in ternary V(V) systems of analytical importance. Due to its masking potential towards iron (III) ions, citrate was chosen as the most suitable third component of a ternary vanadium system with PAR, to form the basis of an RP-HPLC method for direct determination of V in steel.     

Co3O4 Decorated Ti/TiO2 Nanotubes for Photogenerated Cathodic Protection of 304 Stainless Steel

The Co₃O₄ decorated TiO₂ nanotube arrays(NTAs) coatings are fabricated by the combination of anodization and impregna-ting methods. It is found that the introduction of Co₃O₄ can reduce the diffraction intensity of (101) plane of the TiO₂ and accelerate the separation of photogenerated electron/hole pairs. In addition, the open circuit potential(OCP) and the corrosion potential of 304 stainless steel(304SS) with or without Co₃O₄ decorated TiO₂ NTAs were measured under visible light, which indicated the 304SS coupled with Co₃O₄ decorated TiO₂ NTAs had better anticorrosion performance than that of the 304SS or the 304SS coupled with pure TiO₂ NTAs. The enhancement of the cathodic protection performance of the Co₃O₄ decorated TiO₂ NTAs can be ascribed to the matched energy levels and strong interaction between Co₃O₄ and TiO₂ NTAs, and the improvement of light absorption.