Investigation of the performance of bipolar transverse plate ESP in the sintering flue control

In order to improve the particle collection efficiency of the electrostatic precipitator (ESP), a transverse plate ESP with bipolar discharge electrodes is proposed. The simulations of the velocity distribution have shown that when the inlet velocity is 1 m/s, within the range of 40 mm from electrode plate, the average velocities of windward side and leeward side are less than 0.7 m/s and 0.3 m/s respectively. It is clear that the velocity near the collection electrode plate of this bipolar ESP is much lower than that of the ordinary ESP at the same inlet velocity. This low velocity can lead to higher efficiency for fine dust collection due to the less dust re-entrainment in ESP. It is also found that the average velocities are getting lower when the distance between plates electrodes are greater than 150 mm in accordance with the simulations. The voltage current characteristics of the bipolar ESP are superior to the ordinary ESP. The pressure drop of the bipolar ESP is about 30% higher than that of the ordinary one. The dust penetration of the bipolar ESP is about 54% less than that of the ordinary ESP when the sintering dust with 25.405 μm mass median diameter is used as the test particulate under the condition of the electric field from 2.1 kV/cm to 3.2 kV/cm and the velocity from 1.0 m/s to 1.5 m/s.     

活性破片对钢板侵彻性能的实验研究

进行了弹道枪发射实验,研究了活性破片对钢板侵彻性能和毁伤效应。测量破片穿透不同厚度钢板的临界速度,采用高速摄影仪观察破片侵彻钢板过程和反应现象。实验结果表明,活性破片在497~1374 m/s速度范围内,撞击钢板时发生了反应,并伴随有强烈的燃烧、爆炸现象。在战斗部设计关心的1 500~2 200 m/s范围内,活性破片对典型的6 mm厚等效钢板具有足够的侵彻能力;且穿孔直径大于惰性钢破片。聚合物基体材料的强度低和撞靶反应是造成活性破片侵彻穿甲能力弱于钢破片的主要原因。活性材料强度和密度相对钢靶较低,导致撞击靶板过程中发生较大的镦粗变形以及侵靶过程中反应对靶孔产生径向膨胀效应使穿孔孔径增加。     

弹丸侵彻钢板夹层钢纤维混凝土遮弹板数值模拟

为研究钢板夹层钢纤维混凝土遮弹板抗侵彻性能,利用ANSYS/LS-DYNA3D有限元计算软件,数值模拟了高速弹丸撞击钢板夹层钢纤维混凝土遮弹板的过程,得到了弹丸侵彻靶板的速度、加速度变化曲线。通过分析不同弹速产生的弹丸速度及加速度的变化,得出不同初速条件下弹丸速度与时间的关系和加速度变化规律。该研究为组合遮弹板结构抗侵彻性能提供了理论依据,解决了过程计算的繁琐问题。     

杆式射流侵彻半无限靶的理论分析

 理论分析高速杆式射流侵彻半无限靶过程时,考虑速度梯度对聚能射流的影响,将射流进行分段计算,得到了射流拉伸后实际碰靶时的微元长度和直径变化。采用伯努利方程和静力学方法,通过对射流形状和速度分布作线性近似,理论分析了高速杆式射流侵彻半无限靶的过程,得到了靶体中的侵彻深度和侵彻孔径与射流长度、速度及直径之间的关系。将模拟结果与实验结果进行对比,结果表明理论分析结果与侵彻实验结果符合较好。     

聚能射流侵彻的一种耦合算法

介绍了一种能有效模拟聚能射流侵彻过程的计算方法，即二维数值解和解析解相耦合的方法。实际应用表明，此方法计算结果准确可靠，经济省时，其软件是聚能装药优化设计的实用工具。     

卵形头部刚性弹侵彻厚靶的半解析模型

基于确定靶体中速度势和速度场的方法分析刚性卵形头部弹体对有限厚靶的侵彻问题。推导了靶体中速度场与应力场的计算方法,利用据此编制的计算程序,计算了卵形头部钢弹体对铝靶的侵彻与穿透问题,给出了侵彻深度与剩余速度同初始碰撞速度的关系。结果表明,在对实验参数不经过任何调整的情况下,得到了同试验曲线相吻合的结果。可以看出该方法的有效性。     

Interaction of a shaped-charge jet with a target possessing an axial orifice

Interaction of a shaped-charge jet with a target possessing an axial orifice is studied experimentally. For an orifice diameter approximately equal to 0.2D, where D is the shaped-charge diameter, the shaped-charge penetration depth is found to be substantially reduced owing to deviation of the shaped-charge jet axis from the shaped charge axis because of imperfections of the manufacturing technology. A diameter of the target orifice providing unconstrained penetration of the shaped-charge jet is determined. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 49, No. 6, pp. 13–16, November–December, 2008.     

间隔靶对射流侵彻影响的数值模拟和实验研究

对某聚能装药射流侵彻靶板的过程进行了数值模拟 ,得出其碰撞点附近应力分布与传统理论相符 ,侵彻深度与实验结果及工程计算结果基本相符 ;分别对该聚能装药侵彻连续靶和间隔靶的过程进行了数值模拟 ,数值模拟结果显示间隔靶的侵彻深度明显低于连续靶的侵彻深度 ,这说明侵彻开坑阶段的能耗侵深比远大于准定常阶段。为了验证间隔靶对射流侵彻的影响 ,用另一聚能装药分别对连续靶和间隔靶进行了侵彻实验 ,并排除了炸高的影响。实验结果也表明 ,间隔靶对射流侵彻的确存在着不利影响。还结合数值模拟及实验结果对传统的侵彻公式进行了修正。     

SIMILARITY LAWS AND SCALING OF PENETRATION TESTS

利用球形空腔膨胀理论的响应函数对靶板在弹体撞击下的侵彻进行分析，并基于量纲理论建立了侵彻相似律的一般形式.通过对侵彻混凝土靶的已有实验数据进行分析，得到了不同缩比因子下，无量纲侵彻深度曲线随侵彻速度不同而发生偏转和偏移.考虑到材料的应变率效应和损伤演化，认为几何相似律对混凝土等脆性材料在抗侵彻时不成立，有必要引入材料应变率效应和损伤演化对几何相似律的修正.     

On the penetration of a rotating impactor into an elastic-plastic medium

This research is devoted to the modeling of high-speed rectilinear penetration of a rigid axisymmetric body (impactor with a flat bluntness) into an elastic–plastic media with account for its rotation about the axis of symmetry. The body has an arbitrary shape of the meridian. The resistance to the motion is represented as the sum of the body drag and the contribution of friction. The dynamic system governing the body motion is derived and the qualitative and numerical analysis of the projectile movement and perforation of a slab are performed. The problem of shape optimization of impactor with a flat bluntness is studied using evolutionary algorithm.