Highly Luminescent Red Phosphorescent OLED with Interfacial Layers for Hole Transport and Electron Injection

Four kinds of red phosphorescent organic light-emitting devices were fabricated and compared to investigate the effect of interfacial layers for hole transport and electron injection. 1 nm-thick LiF in the device A and C and 1 nm-thick Cs₂CO₃ in the device B and D were deposited as an electron injection layer between the anode and the electron transport layer, and 5 nm-thick layer of dipyrazion[2,3-f:2′,2′-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile[HATCN] was inserted as a hole transport interfacial layer between the hole injection layer and the hole transport layer only in the device C and D. Under a luminance of 1000 cd/m², the power efficiencies were 7.6 lm/W and 8.5 lm/W in the device A and B, and 8.6 lm/W and 13.4 lm/W in the device C and D. The quantum efficiency of the device D was 15.8% under 1000 cd/m² which was somewhat lower than those of the device A and C, but a little higher than that of the device B. The luminance of the device D was much higher than those of the other devices at a given votage. The luminance of the device D at 7 V was 23,710 cd/m², which was 13.0, 3.4, and 4.0 times higher than those of the device A, B, and C at the same voltage, respectively.     

页岩气低伤害超临界CO2凝胶压裂液研究

针对常规水压裂液会对页岩造成伤害，容易产生水锁，不易返排，还造成水资源消耗和污染环境等问题，制备了低伤害二氧化碳凝胶压裂液。将自备的F2EU和F4EU增稠剂加入到超临界CO₂基液中，探究两种增稠剂的加入量对CO₂凝胶压裂液黏度的影响，综合考虑成本与效果，优选了2%的F4EU增稠剂，可将CO₂的黏度增至15.4 mPa·s。研究了温度、压力以及剪切速率对凝胶压裂液黏度的影响。实验结果表明，随着温度升高黏度总体降低，但中间出现一个短暂升高阶段；随着压力上升压裂液黏度增加；随着剪切速率的增加压裂液黏度下降，属于一种典型的剪切变稀的假塑性流体。F4EU超临界CO₂凝胶压裂液的平均伤害率为1.39%，远远小于常规压裂液对岩芯的伤害率。实验表明，F4EU超临界CO₂凝胶压裂液在页岩气压裂开采中具有良好的应用前景。     

Monte Carlo simulation of electric conductivity for pure and doping fullerene (C60)

In this paper, we have used Monte Carlo (MC) method to simulate and study the temperature and doping effects on the electric conductivity of fullerene (C60). The results show that the band gap has reduced by the doping and the charge carrier transport is facilitated from valence band to conduction band by the temperature where is touched a 300 K. In this case, the conductivity reached a value of $4\times {10}^{-7}\text{S}{\text{cm}}^{-1}$. The electric conductivity of C60 can increase by the triphenylmethane dye crystal violet (CV) alkali metal to reach $4\times {10}^{-3}\text{S}{\text{cm}}^{-1}$ at 303 K. Our results of MC simulation have a good agreement with those extracted from literature [10], [33].     

Convergence of solutions for the fractional Cahn–Hilliard system

This paper deals with the Cauchy–Dirichlet problem for the fractional Cahn–Hilliard equation. The main results consist of global (in time) existence of weak solutions, characterization of parabolic smoothing effects (implying under proper condition eventual boundedness of trajectories), and convergence of each solution to a (single) equilibrium. In particular, to prove the convergence result, a variant of the so-called ?ojasiewicz–Simon inequality is provided for the fractional Dirichlet Laplacian and (possibly) non-analytic (but $C^1$) nonlinearities.     

Amphiphilic thermoset elastomers from metal‐free,click crosslinking of PEG‐grafted silicone surfactants

The hydrophobicity of silicone elastomers can compromise their utility in some biomaterials applications. Few effective processes exist to introduce hydrophilic groups onto a polysiloxane backbone and subsequently crosslink the material into elastomers. This problem can be overcome through the utilization of metal‐free click reactions between azidoalkylsilicones and alkynyl‐modified silicones and/or PEGs to both functionalize and crosslink silicone elastomers. Alkynyl‐functional PEG was clicked onto a fraction of the available azido groups of a functional polysiloxane, yielding azido reactive PDMS‐g‐PEG rake surfactants. The reactive polymers were then used to crosslink alkynyl‐terminated PDMS of different molecular weights. Using simple starting materials, this generic yet versatile method permits the preparation and characterization of a library of amphiphilic thermoset elastomers that vary in their composition, crosslink density, elasticity, hydrogel formation, and wettability. An appropriate balance of PEG length and crosslink density leads to a permanently highly wettable silicone elastomer that demonstrated very low levels of protein adsorption. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1082–1093     

Fe~(3+)-水合红菲绕啉二磺酸钠分光光度法测定异烟肼

基于异烟肼分子结构中的酰肼基具有较强的还原性,可将Fe~(3+)还原为Fe~(2+),选择水合红菲绕啉二磺酸钠作为Fe~(2+)的显色剂,建立了可见分光光度法测定异烟肼的新方法.在最佳实验条件下,异烟肼的浓度在0.04~3.2μg·mL-1范围内符合比尔定律,表观摩尔吸光系数ε=1.14×104 L·mol~(-1)·cm~(-1),检测限为0.033μg·mL~(-1).方法可用于异烟肼片剂和尿样中异烟肼含量的测定.     

Theory of chemical bonds in metalloenzymes XXII: a concerted bond-switching mechanism for the oxygen–oxygen bond formation coupled with one electron transfer for water oxidation in the oxygen-evolving complex of photosystem II

ABSTRACT

QM(UB3LYP)/MM(AMBER) calculations were performed for the locations of the transition structure (TS) of the oxygen–oxygen (O–O) bond formation in the S₄ state of the oxygen-evolving complex (OEC) of photosystem II (PSII). The natural orbital (NO) analysis of the broken-symmetry (BS) solutions was also performed to elucidate the nature of the chemical bonds at TS on the basis of several chemical indices defined by the occupation numbers of NO. The computational results revealed a concerted bond switching (CBS) mechanism for the oxygen–oxygen bond formation coupled with the one-electron transfer (OET) for water oxidation in OEC of PSII. The orbital interaction between the σ-HOMO of the Mn(IV)₄–O₍₅₎ bond and the π*-LUMO of the Mn(V)₁=O₍₆₎ bond plays an important role for the concerted O–O bond formation for water oxidation in the CaMn₄O₆ cluster of OEC of PSII. One electron transfer (OET) from the π-HOMO of the Mn(V)₁=O₍₆₎ bond to the σ*-LUMO of the Mn(IV)₄–O₍₅₎ bond occurs for the formation of electron transfer diradical, where the generated anion radical [Mn(IV)₄–O₍₅₎]^-? part is relaxed to the ?Mn(III)₄?…?O₍₅₎^- structure and the cation radical [O₍₆₎=Mn(V)₁]⁺ ? part is relaxed to the ⁺O₍₆₎–Mn(IV)₁? structure because of the charge-spin separation for the electron-and hole-doped Mn–oxo bonds. Therefore, the local spins are responsible for the one-electron reductions of Mn(IV)₄->Mn(III)₄ and Mn(V)₁->Mn(IV)₁. On the other hand, the O₍₅₎^- and O₍₆₎⁺ sites generated undergo the O–O bond formation in the CaMn₄O₆ cluster. The Ca(II) ion in the cubane- skeleton of the CaMn₄O₆ cluster assists the above orbital interactions by the lowering of the orbital energy levels of π*-LUMO of Mn(V)₁=O₍₆₎ and σ*-LUMO of Mn(IV)₄–O₍₅₎, indicating an important role of its Lewis acidity. Present CBS mechanism for the O–O bond formation coupled with one electron reductions of the high-valent Mn ions is different from the conventional radical coupling (RC) and acid-base (AB) mechanisms for water oxidation in artificial and native photosynthesis systems. The proton-coupled electron transfer (PC-OET) mechanism for the O–O bond formation is also touched in relation to the CBS-OET mechanism.     

Gas-phase 21Ne NMR studies and the nuclear magnetic dipole moment of neon-21

Gas-phase ²¹Ne nuclear magnetic resonance spectra were measured at the natural abundance of ²¹Ne isotope for samples consisting of pressurized neon up to 60 bar at room temperature and applying the magnetic field of the strength B₀ = 11.7574 T. It showed that the nuclear magnetic resonance frequency is linearly dependent on the density of gaseous neon. The resonance frequency was extrapolated to the zero-density point, and it permitted the determination of the ²¹Ne nuclear magnetic moment, μ(²¹Ne) = 0.6617774(10) μ_N. The present value of μ(²¹Ne) is not influenced by the bulk magnetic susceptibility of neon and interactions between neon atoms; therefore, it is more precise and reliable than the previous result obtained for μ(²¹Ne).     

Azobenzene‐Functionalized Cage Silsesquioxanes as Inorganic–Organic Hybrid,Photoresponsive, Nanoscale,Building Blocks

Mono‐ and octa‐azobenzene‐functionalized cage silsesquioxanes were easily synthesized by the reaction of 4‐bromoazobenzene with monovinyl‐substituted octasilsesquioxane and cubic octavinylsilsesquioxane through the Heck coupling reaction. Excited‐state energies obtained from time‐dependent density functional theory (TDDFT) and the CAM‐B3LYP functional correlate very well with experimental trans–cis photoisomerization results from UV/Vis spectroscopy. These azobenzene‐functionalized cages exhibit good thermal stability and are fluorescent with maximum emission at approximately 400 nm, making them potential materials for blue‐light emission.     

Recent advances and challenges in materials for 3D bioprinting

3D bioprinting has been developed as a promising technology in a wide variety of biomedical applications. However, the successful implementation of bioprinting is still heavily restricted by the relatively narrow range of printable and biocompatible materials. Recently, many comprehensive reviews of the main bioprinting methods, commonly used bioprinting materials and the trending bioprinting applications have been carried out. In this review, we focused on the trends in the development of materials for 3D bioprinting. The significance and recent advances of ECM-based materials, multi-material and stimuli-responsive materials for bioprinting were summarized successively. Moreover, the challenges in current studies and future perspectives of materials for 3D bioprinting were discussed.