离子液体介质中FeCl3•6H2O催化下芳香醛与5,5-二甲基-1,3-环己二酮的缩合反应

考察了在离子液体1-正丁基-3-甲基咪唑四氟硼酸盐([bmim][BF₄])介质中, 芳香醛与5,5-二甲基-1,3-环己二酮的缩合反应. 实验结果表明, 在催化量的FeCl₃•6H₂O存在下, 该反应可高产率地生成氧杂蒽二酮类化合物3; 而在TMSCl/FeCl₃•6H₂O复合催化体系的催化下, 则得到氧杂蒽二酮类化合物的开环衍生物4, 反应具有非常好的选择性. 该论文提供的方法操作简单、产率高、选择性好而且对环境友好. 在反应结束后, 所用催化剂及离子液体都很容易回收, 并能有效重复使用.     

吡啶-2-甲酸镍的合成及其晶体结构

以吡啶 2 甲酸和Ni(ClO4)2·6H2O为原料反应制得配合物[Ni(C5H4NCOO)2(H2O)2]2H2O,并通过X 射线衍射法测定其晶体结构.该化合物属于单斜晶系,空间群P21/n,晶胞参数:a=0.97351(15)nm,b=0.52254(8)nm,c=1.4483(2)nm,β=90.119(3)°,V=0.7367(2)nm3,Z=2,Dc=1.690g/cm3,μ=1.362mm 1,F(000)=388,结构偏离因子R1=0.0316,wR2=0.0902,共收集到4771个强度数据,其中1700个独立衍射点,1489个(I>2σ(I))可观测点.X 射线分析表明晶体是由分子间氢键和π π弱相互作用堆积而成的二维层状结构.     

氧化共沉淀法制备纳米级掺锑α—Fe2O3气敏陶瓷粉料

氧化共沉淀法制备纳米级掺锑α┐Ｆｅ２Ｏ３气敏陶瓷粉料王忠春＊＊刘尔生陈耐生＊黄金陵（福州大学化学系福州３５０００２）关键词α－Ｆｅ２Ｏ３陶瓷，锑掺杂气敏材料，纳米材料１９９６－１０－０５收稿，１９９７－０４－２２修回福建省科委资助项目＊＊现在上海硅酸...     

微波辅助快速制备2D/1D ZnIn2S4/TiO2 S型异质结及其光催化制氢性能

The threat and global concern of energy crises have significantly increased over the last two decades. Because solar light and water are abundant on earth, photocatalytic hydrogen evolution through water splitting has been considered as a promising route to produce green energy. Therefore, semiconductor photocatalysts play a key role in transforming sunlight and water to hydrogen energy. To date, various photocatalysts have been studied. Among them, TiO₂ has been extensively investigated because of its non-toxicity, high chemical stability, controllable morphology, and high photocatalytic activity. In particular, 1D TiO₂ nanofibers (NFs) have attracted increasing attention as effective photocatalysts because of their unique 1D electron transfer pathway, high adsorption capacity, and high photoinduced electron–hole pair transfer capability. However, TiO₂ NFs are considered as an inefficient photocatalyst for the hydrogen evolution reaction (HER) because of their disadvantages such as a large band gap (~3.2 eV) and fast recombination of photoinduced electron–hole pairs. Therefore, the development of a high-performance TiO₂ NF photocatalyst is required for efficient solar light conversion. In recent years, several strategies have been explored to improve the photocatalytic activity of TiO₂ NFs, including coupling with narrow-bandgap semiconductors (such as ZnIn₂S₄). Recently, microwave (MW)-assisted synthesis has been considered as an important strategy for the preparation of photocatalyst semiconductors because of its low cost, environment-friendliness, simplicity, and high reaction rate. Herein, to overcome the above-mentioned limiting properties of TiO₂ NFs, we report a 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction synthesized through a microwave (MW)-assisted process. Herein, the 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction was constructed rapidly by using in situ 2D ZnIn₂S₄nanosheets decorated on 1D TiO₂ NFs. The loading of ZnIn₂S₄ nanoplates on the TiO₂ NFs could be easily controlled by adjusting the molar ratios of ZnIn₂S₄ precursors to TiO₂ NFs. The photocatalytic activity of the as-prepared samples for water splitting under simulated solar light irradiation was assessed. The experimental results showed that the photocatalytic performance of the ZnIn₂S₄/TiO₂ composites was significantly improved, and the obtained ZnIn₂S₄/TiO₂ composites showed increased optical absorption. Under optimal conditions, the highest HER rate of the ZT-0.5 (molar ratio of ZnIn₂S₄/TiO₂= 0.5) sample was 8774 μmol·g^-1·h^-1, which is considerably higher than those of pure TiO₂ NFs (3312 μmol·g^-1·h^-1) and ZnIn₂S₄nanoplates (3114 μmol·g^-1·h^-1) by factors of 2.7 and 2.8, respectively. Based on the experimental data and Mott-Schottky analysis, a possible mechanism for the formation of the S-scheme heterojunction between ZnIn₂S₄ and TiO₂ was proposed to interpret the enhanced HER activity of the ZnIn₂S₄/TiO₂heterojunctionphotocatalysts.      

高温下硅酸锂吸收CO2的研究

以SiO₂和Li₂CO₃为反应原料，采用高温固相法于不同温度下合成了一系列可在高温500~750 ℃之间直接吸收CO₂的硅酸锂(Li₄SiO₄)材料。采用扫描电子显微镜(SEM)、X射线粉末衍射仪(XRD)分别观察和评价了合成材料的表面形貌与结构特征，用热重分析仪(TG)研究了硅酸锂材料吸收CO₂的性能。实验结果表明，在750 ℃下煅烧6 h即可合成出吸收CO₂性能良好的硅酸锂材料，在CO₂气氛下，于700 ℃保持约15 min即可达到吸收平衡，其吸收量约达43%(wt)左右。与文献报道相比，材料的合成条件有所改善，材料吸收CO₂的容量也有较大提高。     

双-单齿芳香酰胺型配体桥联La3＋一维配位聚合物的合成与晶体结构

通过硝酸镧和双-单齿芳香酰胺型配体L {L＝1,4-双[(2'-苄胺甲酰基苯氧基)-甲基]苯}之间的反应得到了配位聚合物{[La(NO₃)₃]₂•L₃}_n, 并用X射线单晶衍射测定了配合物的晶体结构. 配合物为三斜晶系, _P1空间群, 晶胞参数a＝1.1298(2) nm, b＝1.2689(1) nm, c＝2.1030(3) nm, α＝81.189(9)°, β＝80.95(1)°, γ＝65.832(9)°, V＝2.7032(6) nm³, Z＝2, R＝0.0267, wR＝0.0679, La^3＋为9配位, 呈变形的三帽三角棱柱配位构型. 配合物通过配体的桥联作用形成一维环链相间的配位聚合结构, 由于相邻链间不存在氢键和π-π堆积作用, 所以配合物是以单链形式堆积排列.     

溶胶-凝胶法制备还原态K-Co-Mo催化剂的合成醇性能

应用溶胶-凝胶法制备了还原态K-Co-Mo催化剂, 比较了不同的组分和不同的反应条件对合成醇性能的影响。实验结果表明，适量钾和钴助剂的添加能显著提高催化剂合成醇的性能，尤其是提高了C2+醇的选择性。此外，反应温度、压力以及空速对合成醇影响明显，升高温度可以提高催化反应中低碳醇的收率，但选择性下降；增加压力和空速可以提高低碳醇的收率和选择性，对合成低碳醇有利。在230 ℃，6.0 MPa，14 400 h－1条件下，催化剂合成低碳醇的收率为375.4 g/kg·h，选择性为70.2%，C1OH/C2+OH为0.48。     

芥子气模拟剂2-氯乙基乙基硫醚的光催化降解

利用连续流动微反、原位红外和GC/MS等手段考察了芥子气模拟剂2-氯乙基乙基硫醚（2-CEES）在P25 TiO2上的光催化降解反应,证实CO2和H2O是这个反应的最终产物.详细的跟踪分析表明,除了CO2和H2O外,在反应的气相混合物中可检测到C2H4、CH3CHO、CH4、CO、HCl和H2S；少量小分子的羧酸、醚和砜；微量C2H5SC2H5、C2H5S2C2H5、C2H5SC2H4Cl和CH2ClCH2Cl等中间产物;在反应后的催化剂表面可检测到C2H5S2C2H5、C2H5SC2H4OH、C4H9S2C2H5和C2H5S2C2H4OH、等物.根据这些结果提出了2-CEES光催化降解的反应机理,推断2-CEES的光催化降解涉及脱氯、C－S键断裂、有机硫化物光聚合和裂解等复杂过程最终转化为CO2和H2O.认为各种硫物种在表面的积聚引起了催化剂的缓慢失活.     

配位聚合物{[Co2(HBTC)2(H2O)6]·C4H10N2·2H2O}n的水热合成、结构表征及荧光性质

采用水热法合成了配位聚合物[Co2(HBTC)2(H2O)6]·C4H10N2·2H2O}n(H3BTC为1,3,5-均苯三羧酸,C4H10N2为哌嗪),通过X射线单晶衍射、红外光谱和荧光光谱进行表征,并用TGA研究了该配位聚合物的热稳定性.晶体属三斜晶系,P1空间群,a=1.05437(9)nm,b=1.05485(9)nm,c=0.71482(5)nm,α=102.4623(28)°,β=91.3500(42)°,γ=111.0186(29)°,V=0.72018(10)nm3,Mr=764.37,Dc=1.762g·cm-3,Z=1,μ(MoKα)=1.25mm-1,F(000)=394,R=0.0307,wR=0.0815.晶体的基本构建单元中包含2个Co()中心、2个配位的HBTC分子和6个配位的水分子.基本构建单元通过相互链接形成具有“Z”型结构的一维配位聚合链,链间通过两种不同的氢键(O—H…O和N—H…O)相互作用,进而形成具有三维骨架结构的微孔晶体,微孔大小为0.71nm×0.82nm.荧光光谱表明,常温下用λex=312nm的光激发后,配位聚合物在329nm处出现强烈的荧光发射.     

Synthesis of Lanthanide Coordination Polymers with Benzophenone-4,4′-dicarboxylate： Effect of Lanthanide Contraction on Structures

Four lanthanide coordination polymers with benzophenone‐4,4′‐dicarboxylic acid (H₂bpndc) and 1,10‐phenanthroline (phen), [Ln₂(bpndc)₃(phen)] (Ln=La (1), Pr (2) and Tb (3)), [Yb(bpndc)₁₅(phen)].05H₂O (4) were obtained through solvothermal synthesis. The crystallographic data show that 1, 2, and 3 are isostructural, the Ln(III) ions in 1, 2 and 3 are all eight‐ and ten‐coordinated, respectively, and thus the Ln(III) ions are connected by bpndc ligands, resulting in an interpenetrating 3D structure. While in 4, the Yb(III) ions are eight‐coordinated and connected by bpndc ligands into a 3D structure with 1D rhombic channels, which result from the effect of lanthanide contraction from La(III) to Yb(III) ions, and the bpndc ligands in 1, 2, 3, and 4 display three types of coordination modes.