Lower bounds on the cluster size distribution

We rigorously prove that the probabilityP _n that the origin of ad-dimensional lattice belongs to a cluster of exactlyn sites satisfiesP _n > exp(–n ^(d–1)/d ) whenever percolation occurs. This holds for the usual (noninteracting) percolation models for any concentrationp > p _c , as well as for the equilibrium states of lattice spin systems with quite general interactions. Such a lower bound applies also if no percolation occurs, but if it appears in some other phase of the system.     

Cadmium colloids from non-aqueous solvents

Cadmium colloids have been prepared by Chemical Liquid Deposition (CLD). The metal is evaporated to yield atoms which are solvated at liquid nitrogen temperature, and upon warming, stable liquid colloids are formed with particle size ranging between 25–100 Å. Zeta potentials were calculated according to the conversion of Hunter and the Hückel equation, for ethanol and dimethyl sulphoxide. UV/VIS measurement of most of the black colloids showed absorption band around 280 nm. For comparison, we prepared CdS colloid with size 400–625 Å. The colloids are stable to oxidation in air and/or oxygen bubbling. The synthesis of colloids and films from Cd with acetone, 2-butanone, ethanol, 2-propanol, 2-methoxyethanol, DMF and DMSO is reported. Transmission Electron Microscopy (TEM) allows us to determine particle size.     

Monte Carlo simulation of adsorption of binary and quaternary alkane isomers mixtures in zeolites: Effect of pore size and structure

Grand canonical Monte Carlo and configurational bias Monte Carlo techniques were employed to simulate the adsorption of binary mixtures of butane isomers and quaternary mixtures in nine zeolites at 300 K. For binary mixtures the results show there is a critical pore size, which is 10-membered-ring about 5.6 Å. The channel sizes of BEA, ISV, MOR and CFI are larger than this critical pore size, they prefer i-butane than n-butane, whereas TON with smaller channel size than critical pore size prefers n-butane than i-butane, but its selectivity decreases with pressure increasing. MFI, MEL and TER prefer i-butane than n-butane at low pressure, but with pressure increasing, the selectivity is reversed. BOG prefers i-butane than n-butane but the selectivity decreased with pressure increasing. It demonstrates that the adsorption and selectivity are controlled by both pore size and pore structure. The n-butane–i-butane–n-pentane–2-methylbutane quaternary mixtures adsorbed in these nine zeolites were studied, and the results show alkane chain length dependence at low pressure, but the adsorption is controlled by pore size and structure with pressure increasing in all the zeolites except for TON and BOG.     

超临界CO2法制备头孢唑啉钠脂质体

采用超临界CO2(scCO2)流体代替有机溶剂一步法制备了头孢唑啉钠药物载体脂质体. 研究了该脂质体的尺寸、稳定性和药物的包封率. 结果表明, 脂质体的尺寸和稳定性依赖于制备压力, 脂质体对头孢唑啉钠的包封率与乙醇和脂浓度有关, 采用超临界CO2法制备脂质体的药物包封率比采用薄膜分散法(Bangham method)制备的包封率高.     

Time shift correction in second-order liquid chromatographic data with iterative target transformation factor analysis

When the generalized rank annihilation method (GRAM) is applied to liquid chromatographic data with diode-array detection, an important problem is the time shift of the peak of the analyte in the test sample. This problem leads to erroneous predictions. This time shift can be corrected if a time window is selected so that the chromatographic profile of the analyte in the test sample is trilinear with the peak of the analyte in the calibration sample. In this paper we present a new method to determine when this condition is met. This method is based on the curve resolution with iterative target transformation factor analysis (ITTFA). The calibration and test matrices are independently decomposed into profiles and spectra, and aligned before GRAM is applied. Here we study two situations: first, when the calibration matrix has one analyte and second, when it has two analytes. When the calibration matrix has two analytes, we selectively determine the time window for the analyte to be quantified. There were considerably fewer prediction errors after correction.     

Determination of Fibre Pore Structure: Influence of Salt,pH and Conventional Wet Strength Resins

It has been shown, in the present investigation, that the two methods used to investigate the pore size distribution of unbleached chemical pulps, i.e. inverse size exclusion chromatography (ISEC) and nuclear magnetic resonance (NMR), give different average pore radius for the pores inside the fibre wall. This is due to the way in which these experiments are performed and the sensitivity of the methods to different types of pores in the cell wall. It was also shown that the two methods gave different results when changing the pH and the ionic strength of the pulp suspension. The pore radius, as detected with ISEC, decreased with both increasing ionic strength and decreasing pH, indicating a loose structure of the exterior of the fibrillar network. However, the pore radius as detected with NMR, was virtually unaffected when increasing the ionic strength, indicating a very rigid structure of the interior of the fibre wall. Decreasing pH though, lead to a decrease in pore radius indicating that upon protonation of the carboxylic groups in the fibre wall, the electrostatic repulsion is diminished and the average pore radius decreases. The NMR technique was also used to study wet strength aid penetration into the fibre wall. It was shown that wet strength aids with a small molecular weight, penetrated the fibre wall, as detected by a decrease in pore radius. It was also shown that addition of different wet strength aids increased the tensile index of the sheet and decreased the fibre strength, measured as zero span-strength of the sheets.     

甲醇重整反应中Pt/γ-Al2O3催化剂纳米Pt粒径与催化性能关系研究

利用硝基甲烷还原法在室温条件下得到了纳米Pt粒径可控的担载Pt/γ-Al₂O₃催化剂, 并利用甲醇重整反应为反应探针考察了Pt粒径与催化反应性能之间的关系, 发现催化反应的性能与担载贵金属颗粒粒径之间存在明显的相关性. 通过透射电镜(TEM)、X射线衍射(XRD)、程序升温还原(TPR)等测试手段对催化剂进行表征, 发现钠米Pt的粒径大小不但影响甲醇重整反应的活性, 同时也影响反应的选择性, 即催化剂的催化性能与担载贵金属粒径之间存在明显的尺度效应.     

Achieving high yield of Ti3C2Tx MXene few-layer flakes with enhanced pseudocapacior performance by decreasing precursor size

Ti₃C₂T_x, a most studied member of MXene family, shows promise as a candidate electrode for pseudocapacitor due to its electronic conductivity and hydrophilic surface. However, the unsatisfactory yield of Ti₃C₂T_x few-layer flakes significantly restricted it in real applications. Here, we proposed a simple solution to boost the yield of Ti₃C₂T_x few-layer flakes by decreasing precursor size. When using the small 500 mesh Ti₃AlC₂ powders as raw material, high yield of 65% was successfully achieved. Moreover, the as-received small flakes also exhibit an enhanced pseudocapacior performance owing to their excellent electrical conductivity, expanded interlayer space and more O content on the surface. This work not only sheds light on the cost effective mass production of Ti₃C₂T_x few-layer flakes, but also provides an efficient solution for the design of MXene electrodes with high pseudocapacior performance.     

EFFECTS OF COUPLING AGENTS ON THE CRYSTALLIZATION BEHAVIOR OF PP/T-ZnOw COMPOSITES

The objectives of this paper are to understand the crystallization behavior of polypropylene(PP)composites with surface modified tetra-needle-shaped zinc oxide whisker(T-ZnOw).T-ZnOw was surface modified with different coupling agents,such as silane coupling agents(KH-550,KH-560)and titanate coupling agent(NDZ-105),in order to improve the compatibility between PP and T-ZnOw.DSC and POM were used to characterize the melt and crystallization behavior and the crystalline structures of the composites,respectively.The results show that the surface modified T-ZnOw acts as a nucleating agent of PP crystallization,depending on the coupling agent used for modification.KH-550 and KH-560 have more apparent role in improving the interfacial interaction than NDZ-105 and induce PP crystallization at higher temperature and with smaller spherulites size.The results also suggest that the crystallization behavior depends on not only the content of coupling agent,but also the content of the surface modified T-ZnOw used in the composites.     

The Additive Influence of Propane-1,2-Diol on SDS Micellar Structure and Properties

Micellar systems are colloids with significant properties for pharmaceutical and food applications. They can be used to formulate thermodynamically stable mixtures to solubilize hydrophobic food-related substances. Furthermore, micellar formation is a complex process in which a variety of intermolecular interactions determine the course of formation and most important are the hydrophobic and hydrophilic interactions between surfactant–solvent and solvent–solvent. Glycols are organic compounds that belong to the group of alcohols. Among them, propane-1,2-diol (PG) is a substance commonly used as a food additive or ingredient in many cosmetic and hygiene products. The nature of the additive influences the micellar structure and properties of sodium dodecyl sulfate (SDS). When increasing the mass fraction of propane-1,2-diol in binary mixtures, the c.m.c. values decrease because propane-1,2-diol is a polar solvent, which gives it the ability to form hydrogen bonds, decreasing the cohesivity of water and reducing the dielectric constant of the aqueous phase. The values of ΔGm0 are negative in all mixed solvents according to the reduction in solvophobic interactions and increase in electrostatic interaction. With the rising concentration of cosolvent, the equilibrium between cosolvent in bulk solution and in the formed micelles is on the side of micelles, leading to the formation of micelles at a lower concentration with a small change in micellar size. According to the ¹H NMR, with the addition of propylene glycol, there is a slight shift of SDS peaks towards lower ppm regions in comparison to the D₂O peak. The shift is more evident with the increase in the amount of added propane-1,2-diol in comparison to the NMR spectra of pure SDS. Addition of propane-1,2-diol causes the upfield shift of the protons associated with hydrophilic groups, causing the shielding effect. This signifies that the alcohol is linked with the polar head groups of SDS due to its proximity to the SDS molecules.