Azobenzene‐Functionalized Cage Silsesquioxanes as Inorganic–Organic Hybrid,Photoresponsive, Nanoscale,Building Blocks

Mono‐ and octa‐azobenzene‐functionalized cage silsesquioxanes were easily synthesized by the reaction of 4‐bromoazobenzene with monovinyl‐substituted octasilsesquioxane and cubic octavinylsilsesquioxane through the Heck coupling reaction. Excited‐state energies obtained from time‐dependent density functional theory (TDDFT) and the CAM‐B3LYP functional correlate very well with experimental trans–cis photoisomerization results from UV/Vis spectroscopy. These azobenzene‐functionalized cages exhibit good thermal stability and are fluorescent with maximum emission at approximately 400 nm, making them potential materials for blue‐light emission.     

异构分层无线网络中基于逗留时间的动态流量均衡算法研究

为使异构分层无线网络能服务更多的移动用户,提出了一种基于逗留时间的动态流量均衡算法.该算法首先根据用户移动模型计算其在小区内的逗留时间,然后基于小区呼叫到达率和重叠覆盖小区的流量状态来确定一个周期内呼叫转移的数量,最后依据逗留时间门限值将重负载小区中满足条件的呼叫转移到轻负载的重叠覆盖小区中.为降低切换呼叫掉线率,还对异构网间的呼叫切换策略做了改进.仿真实验结果表明,本算法在新呼叫阻塞率和切换呼叫掉线率等性能指标上比传统方法有显著的提高.     

Adsp-21060的主机接口在实时图像处理中的应用

简要介绍了数字信号处理器Adsp 2 10 6 0和大规模可编程逻辑器件EP1K5 0。详细讨论了Adsp 2 10 6 0的主机接口工作模式以及一个实时图像跟踪处理器的硬件组成原理 ,在这个系统中EP1K5 0充当了主机。调试结果表明 ,所提出的硬件结构设计思想工作效率高 ,完全能够胜任实时图像处理的实际需要。     

一种高精度的非平稳随机信号实时建模算法研究

针对传统的非平稳随机信号时变参数筹分模型算法的不足,论文把非平稳随机信号时变参数差分模型与一种带自适应遗忘因子的RLS算法结合起来,形成一种有效的非平稳随机信号实时建模算法,仿真分析表明该算法不仅能获得快的收敛速度而且能获得高的建模精度。     

Analysis of Distributed DDQ for QoS Router

In a packet switching network, congestion is unavoidable and affects the quality of real‐time traffic with such problems as delay and packet loss. Packet fair queuing (PFQ) algorithms are well‐known solutions for quality‐of‐service (QoS) guarantee by packet scheduling. Our approach is different from previous algorithms in that it uses hardware time achieved by sampling a counter triggered by a periodic clock signal. This clock signal can be provided to all the modules of a routing system to get synchronization. In this architecture, a variant of the PFQ algorithm, called digitized delay queuing (DDQ), can be distributed on many line interface modules. We derive the delay bounds in a single processor system and in a distributed architecture. The definition of traffic contribution improves the simplicity of the mathematical models. The effect of different time between modules in a distributed architecture is the key idea for understanding the delay behavior of a routing system. The number of bins required for the DDQ algorithm is also derived to make the system configuration clear. The analytical models developed in this paper form the basis of improvement and application to a combined input and output queuing (CIOQ) router architecture for a higher speed QoS network.     

串行及并行A/D转换器在高速数据采集中的采样差别性分析

串行和并行接口模式是A/D转换器诸多分类中的一种,但却是应用中器件选择的一个重要指标.在同样的转换分辨率及转换速度的前提下,不同的接口方式不但影响了电路结构,更重要的是将在高速数据采集的过程中对采样周期产生较大影响.本文通过12位串行ADC ADS7822和并行ADC ADS774与AT89C51的接口电路,给出二者采样时间的差异性.     

快速纳秒响应二代近贴聚焦像增强器的批量生产

叙述了二代近贴聚焦像增强器批量生产所用真空设备性能及特点，同时给出了管子工艺考核结果及管子纳秒时间响应特性。工艺考核结果表明，制管工艺可靠、性能稳定，管子批量生产合格率大于70％。     

CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

Quality of Service in VoIP Communication

The focus of this paper lies in the practical aspects of voice over IP communication. VoIP configurations in the H.323 standard will be presented briefly. Following that, the fundamental protocol procedure of H.323 communication will be briefly explained. A further part of the paper will address the subject QoS (quality of service), and present the common measurement methods used in QoS. Results gained from experiments conducted in a VoIP environment will then follow. The investigations concentrate primarily on the load behavior of voice packets in relation to important parameters of this service. The results obtained are presented and evaluated in diagrams. The paper concludes with a summary.     

理想九点五态控制器原理的叙述

用计算的方式叙述理想九点五态控制器的控制原理。为便于人们理解二阶对象的运动中控制的变化过程,将抽象的对象转换为人们熟知的L-R-C电路,通过调节输入电压(即控制作用)的大小和方向来实现对对象性能的调节,并使系统达到理想的性能指标。最后用仿真来验证计算结果的正确性。