高频燃烧红外吸收光谱法测定钨钛合金中碳含量

建立高频燃烧红外吸收光谱法测定钨钛合金中碳含量的分析方法。在1980 W分析功率下,称取0.3 g样品,以2.0 g钨锡及0.5 g纯铁混合助熔,用高频红外分析仪测定碳。碳的含量在0.013%~0.050%范围内与红外吸收峰面积线性相关,相关系数为0.9993。碳的测定下限为3.6μg/g,方法检出限为1.08μg/g。该法测定结果的相对标准偏差为2.97%~4.11%(n=8),碳的加标回收率为96.2%~103.1%。该方法能够满足合金中碳含量的分析要求。     

钇对Nd-Fe-Al-Ni非晶合金热稳定性与晶化行为的影响

采用差示扫描量热法（DSC）、X射线衍射（XRD）和透射电镜（TEM）研究了Y对Nd-Fe-Al-Ni非晶合金热稳定性和晶化行为的影响。结果表明,淬火态的Nd60Fe20Al10Ni10-xYx（x=0,2）合金基本为非晶组织同时还含有少量的淬态相,Y的加入抑制了淬态相的析出。加入Y后,非晶合金的晶化开始温度和晶化峰值温度都向高温方向移动,证明其热稳定性提高。Y的加入改变了合金的晶化方式和最终晶化产物,使非晶基体中析出的晶化相更加弥散圆整细小。并且Y具有在化学上钝化氧杂质的作用,从而抑制了氧的有害作用。利用Kissinger方程获得了Nd60Fe20Al10Ni8Y2非晶合金的晶化开始和晶化峰值激活能分别为1.21和1.16 eV。     

载体γ-Al2O3和钐对非晶态NiB合金热稳定性的影响

用化学还原法制备了NiB、NiB/Al2O3和NiBSm/Al2O3三种催化剂，它们都呈非晶结构.用等离子耦合发射光谱仪(ICP)对催化剂组分进行了分析，采用差示扫描量热法（DSC）对三种催化剂进行了热稳定性分析.结果表明，载体的引入使非晶态NiB合金的体相组成中B的含量降低.将非晶态NiB合金负载到γ-Al2O3上,可以明显改善非晶态合金的热稳定性，少量Sm可以进一步提高晶化温度.晶化激活能数据亦表明了载体和Sm对非晶结构具有良好的稳定作用.载体和Sm可能通过不同的作用提高了非晶态合金的热稳定性.     

Chemical environment of copper at the surface of a CuAl2 model alloy: XPS,MEIS and TEM analyses

Air‐formed oxide on a CuAl₂ model alloy is shown to be free of copper species, with copper enriching in the alloy. With thickening of the oxide by anodizing, copper enriches further to a critical concentration at which its oxidation proceeds with incorporation of Cu(II) species into the film. Such species migrate more rapidly through the film than aluminium species. Incorporation of copper species is associated with generation of oxygen gas within the film and subsequent film rupture is due to release of the gas. Reduction of Cu(II) to Cu(I) species during XPS analysis is characterized and the accelerating role of charge neutralizing is highlighted. Copyright © 2004 John Wiley & Sons, Ltd.     

富镧混合稀土对ZL101A合金组织和机械性能的影响

研究了富镧混合稀土对ＺＬ１０１Ａ合金的铸态、固溶态、Ｔ６状态、重熔态的组织和机械性能的影响，提出了混合稀土中入量低压铸造整体车轮合理的热处理状态。     

Formation of Bi-Sb, Bi-Sn, and Bi-Sb-Sn Nanoclusters in Silica Xerogel Matrices from Mixed-Metal Oxide Precursors

Homogeneous mixed-metal oxides of the general formula (Bi/E/Si)O _x , where E represents a dopant element (E=Sb, Sn, or Sb/Sn), can be prepared using typical sol-gel processing techniques. Reduction of the in-situ Bi(III) and E ions by hydrogen affords nanocomposites of Bi-Sb, Bi-Sn, or Bi-Sb-Sn widely dispersed throughout the silica xerogel matrix. The materials prepared have high Bi-E metal loading of 52–60 wt. % containing Bi-E alloy nanoclusters of 12–15 nm average diameter. These results demonstrate a convenient method for the production of practical quantities of nanostructured bismuth alloy ceramic composites at high metal content.     

高分子合金分离膜材料及结构研究进展

膜材料液相共混制备高分子合金分离膜不但可以调节膜材料与被分离物的亲和性，也在一定程度上改变了膜的结构。本文介绍高分子材料浓相共混对膜材料的亲水性、耐污染性及其它理化性能的影响和对膜结构的调节作用，同时指出高分子材料间的相容性是影响合金膜结构的重要因素。     

X-射线荧光光谱法测定钛铁中的硅、锰、磷、铝

介绍用X-射线荧光光谱仪测定钛铁中Si、Mn、P、Al含量的方法,通过试验确定了合适的研磨时间、压力和保压时间,用压片法制样,建立了各元素的工作曲线,各元素的测定范围分别为Si3.00%～6.00%,Mn1.00%～3.00%,P0.030%～0.070%,Al5.00%～9.00%。通过强度测量得到测定Si、Mn、P、Al的相对标准偏差分别为0.074%、0.308%、0.383%、0.040%,精密度满足测试要求。将该方法测定结果与化学法比对,准确度满足国家标准方法分析误差的要求。     

Characterization of non‐Cr‐based deoxidizers on Al alloy 7475‐T7651

The effects of three non‐chromate‐based deoxidizers, namely NaBrO₃/HNO₃, (NH₄)₄Ce(SO₄)₄/H₂SO₄ and Fe(III)/HF/HNO₃, on the Al alloy 7475‐T7651 were investigated. Several analytical methods were employed, including SEM, AES, transmission electron microscopy (TEM), electron energy‐loss spectroscopy (EELS) and glow discharge optical emission spectrometry (GDOES), to study the effects on the surface of this alloy after each treatment compared with the as‐received and alkaline‐cleaned alloy surfaces. The untreated alloy was found to have a thick oxide of 200–320 nm, consisting mainly of MgO. Alkaline cleaning results in an etching effect that thins the oxide and also deposits a thin silicate layer on the surface. In the case of the deoxidizers, there is significant removal of the native oxide of the alloy by the NaBrO₃/HNO₃ deoxidizer. There is also evidence of intermetallic attack on the alloy. The (NH₄)₄Ce(SO₄)₄/H₂SO₄ deoxidizer, which is a low‐etch‐rate deoxidizer, resulted in a slight thinning of the oxide. However, the effect was not significantly greater than with alkaline cleaning alone. The most effective deoxidizer in reducing the oxide thickness of the alloy is Fe(III)/HF/HNO₃, in which the etch rate was sufficiently high to remove completely the native oxide. In this case, equilibrium between oxide removal and the formation of new oxides on the alloy surface was achieved. Copyright © 2004 John Wiley & Sons, Ltd.     

非对称碰撞约束下形状记忆合金梁的随机响应与分岔

形状记忆合金(SMA)是二十一世纪具有形状记忆效应的新型智能材料.针对具有非对称约束的SMA梁,本文构造了碰撞振动系统.在无碰撞和有碰撞两种情况下,利用随机平均法给出了近似解析结果.数值模拟作为验证解析结果的工具.结果表明,系统能量的概率响应曲线具有非光滑特性.当约束位置发生变化时,系统会出现随机P分岔和D分岔.