IS—95CDMA系统的容量分析

容量的需求是推动ＣＤＭＡ数字蜂窝移动通信开发的主要动力。系统的容量受许多因素的影响，本文针对ＩＳ－９５ＣＤＭＡ系统在采用了功率控制、话音激活和扇区划分技术的情况下，对系统的容量进行了分析，同时也分析了功率控制精度对容量的影响。     

Matrix effects in the determination of butyltin compounds in environmental samples by GC AA after hydride generation

Experiments for the determination of mono-, di and tri-butyltin (MBT, DBT and TBT) by hydride generation/gas chromatography/atomic absorption spectrometry in various matrices (sediment, suspended matter, mussel, algae and water) have revealed that poor butyltin recoveries are obtained in sediments displaying high sulphur and hydrocarbon contents; very poor recoveries were also observed for TBT in sediments with high chlorophyll pigment contents as well as in algal samples. It was however not clear whether the hydride generatin was inhibited by these infering compounds, as was previously assumed in the case of hydrocarbons, or whether interferences affected the atomization rate. Further studies were performed to solve this problem in order to validate this method in the case of analyses of, for example, oil-contaminated sediment and algae. This paper presents the results obtained. It is concluded here that the poor recoveries were due to an inhibition of hydride generation rather than to interference at the atomization stage.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

集群移动通信系统的组网设计

本文对集群移动通信系统在组网设计时应考虑的问题进行了分析，并提出了具体步骤和方法，可供集群系统组网设计时参考。     

Test Generation for Crosstalk-Induced Faults: Framework and Computational Results

Due to technology scaling and increasing clock frequency, problems due to noise effects lead to an increase in design/debugging efforts and a decrease in circuit performance. This paper addresses the problem of efficiently and accurately generating two-vector tests for crosstalk induced effects, such as pulses, signal speedup and slowdown, in digital combinational circuits. These noise effects can propagate through a circuit and create a logic error in a latch or at a primary output. We have developed a mixed-signal test generator, called XGEN, that incorporates classical static values as well as dynamic signals such as transitions and pulses, and timing information such as signal arrival times, rise/fall times, and gate delay. In this paper we first discuss the general framework of the test generation algorithm followed by computational results. Comparison of results with SPICE simulations confirms the accuracy of this approach.     

用激活性非线性介质Nd：MgO：LiNbO3产生二次谐波

以Nd:MgO:LiNbO_3同时兼作激活介质和非线性光学材料,研究自倍频激光器。用小型氙灯泵浦,在室温下获得二次谐波激光(0.547μm) 阈值小于4.8'J,最大输出400μJ/shot,工作温度范围大于20℃～45℃,无光损伤。     

Laser pulse heating of steel surface and flexural wave analysis

Laser gas-assisted material processing finds wide application in industry. The modelling of heating, elastic response of the substrate material, and the wave analysis gives insight into the laser workpiece interaction. In the present study, laser gas-assisted heating of steel is considered. The normal component of the thermal stress is taken as the source of load for the flexural wave generation in the material. The flexural wave generated is simulated and the wave characteristics are analyzed at four locations at the workpiece surface. The numerical scheme employing a control volume approach is introduced when solving the governing equations of flow and heat transfer while finite element and spectran element methods are used when solving the stress and wave equations. It is found that the normal component of the stress is tensile. The dispersion effect of the workpiece material, interference of the reflected beam, and partial overlapping of second mode of the travelling wave enable to identify a unique pattern in the travelling wave in the substrate.     

移动通信市场调查方案的选择及结果分析

为了全面了解全国移动市场状况、邮电部经济中心受邮电部移动局委托制订了全国性移动通信市场调查方案，并对北京，南宁和北海三市进行了调查。本文介绍了这一方案的实施办法，并对上述三市的调查结果进行了分析。     

通讯网的演进

在光纤高速传输技术、光交换与智能光网等与宽带接入、多媒体、3G等网络应用技术的推动下，建设基于IPv6协议的IP基础电信网成为可能。现在IP网正在朝着有序的、可管理的、有QoS保障的、可以支持各类业务的综合业务基础网演进。电信网也正在从网络接入层上、从长途网络层面上、从本地网络层面上、从固定网向含3G在内的移动网络等方面向支持IP技术及其综合业务的方面全面推进。     

A floating-point genetic algorithm for solving the unit commitment problem

This paper proposes a floating-point genetic algorithm (FPGA) to solve the unit commitment problem (UCP). Based on the characteristics of typical load demand, a floating-point chromosome representation and an encoding–decoding scheme are designed to reduce the complexities in handling the minimum up/down time limits. Strategic parameters of the FPGA are characterized in detail, i.e., the evaluation function and its constraints, population size, operation styles of selection, crossover operation and probability, mutation operation and probability. A dynamic combination scheme of genetic operators is formulated to explore and exploit the FPGA in the non-convex solution space and multimodal objective function. Experiment results show that the FPGA is a more effective technique among the various styles of genetic algorithms, which can be applied to the practical scheduling tasks in utility power systems.