Nusselt number correlations for heat transfer to small spheres in thermal plasma flows

Seven different equations predicting heat transfer rates to small spheres in plasma flows are examined considering argon and nitrogan as plasma gases from 300 to 21,000 K at 1 atm. For argon there is a general consensus up to 9000 K, beyond which wide deviations in behavior occur. For nitrogen, the seven correlations are in good agreement up to 4000 K, but show substantial deviations beyond this value. Comparisons with the sparsely available experimental data are made for argon from 300 to 17,000 K and for nitrogen up to 5500 K. Disagreement between the various correlations and experiment can exceed one order of magnitude.     

超稳定TO-8型压力传感器在气体导热系数测定实验中的应用

介绍了TO-8型压力传感器的性能及电源电路.以气体导热系数测定实验为例,用TO-8型压力传感器制成的测压装置代替旋转式麦氏真空计,利用可调针孔式放气阀对真空气压进行连续调节,实现了对测试系统真空度的实时监测.     

替代法测量微安表内阻的不确定度分析

在测量微安表内阻的众多方法中,替代法是最简单的方法。本文全面分析了影响测量结果不确定度的因素,求出了实验测量的最佳条件,计算了普通仪器组合下测量结果的相对不确定度。     

Elastic and Thermophysical Properties of Poly(Vinyl Chloride) and Chlorinated Polyethylene Blends

The results of experimental and theoretical investigations of elastic and thermophysical properties of poly(vinyl chloride) (PVC) and chlorinated polyethylene (CPE) blends are presented. Eight types of specimens with different ratios of weight contents of PVC and CPE (PVC/CPE = 100/0, 90/10, 80/20, 60/40, 40/60, 20/80, 10/90, and 0/100) were tested. The effect of blend composition on the elastic constants (tensile and shear modulus) is discussed. The data on the thermal conductivity, thermal diffusivity, and heat capacity of the blends investigated are also presented.     

离心泵快速启动过程外部特性的试验研究

介绍离心泵快速启动试验装置和试验方法,对一台出口直径为80 mm的小型管道离心泵进行试验研究,分别测试了试验泵的稳态性能和各项瞬态性能,比较分析了两者的区别。结果显示,启动过程中,离心泵的扬程紧跟转速到达最大值,转速稳定后的瞬态性能与稳态假设对应,流量和扬程的上升历程与管路阻力特性直接相关,而转速与其基本无关; 在启动初始阶段,无量纲扬程呈现很大值,继而迅速减小到低于稳态假设值,表现出明显的瞬态效应。     

Assessment of thermal expansion coefficient of methylsilsesquioxane thin film

For the methylsilsesquioxane film whose optical birefringence is almost zero, it was recently reported that its vertical thermal expansion coefficient (CTE) was approximately one order of magnitude larger than the lateral CTE. Though the birefringence is not an absolute predictor of anisotropic behavior, the discrepancy in both the CTEs was so remarkable that it was essential to investigate whether the anisotropy was intrinsic property or not. If the effect of Poisson's ratio is considered in the calculation of the vertical CTE and when elastic modulus measured by surface acoustic wave spectroscopy is used in the assessment of the lateral CTE, both the CTEs are coincident with each other. Therefore, it can be concluded that the discrepancy in the CTEs can be attributed to a higher in‐plane polymer chain orientation but it can also arise from the misleadingly assumed modulus and Poisson's ratio. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3109–3120, 2006     

金属PTC陶瓷复合材料结构及其导电机理

研究了金属ＰＴＣ陶瓷复合材料的电学性能和其材料组分。结果表明，掺入金属的ＰＴＣ陶瓷材料经氮气中烧结，然后在空气中进行热处理，材料表面形成高势垒层，金属ＰＴＣ陶瓷复合材料的室温电阻较ＰＴＣ的陶瓷高。样品之中存在大量不同类型的极化，在低温时样品电阻较高，温度增加后，大量各种类型离子极化出现，在变价金属铁的变价导电作用下，削弱表面势垒，使金属ＰＴＣ陶瓷复合材料电阻降低，表现出ＮＴＣ现象。在电场作用下，正负电荷、晶粒畸变和空位缺陷等产生空间电荷极化使金属ＰＴＣ陶瓷复合材料有较高介电常数。介电损耗（ｔｇδ）频谱和介电δ温度谱上都出现一个介电峰，其主要原因是跃迁极化，金属阳离子由一个位置跃迁到另一个位置，在介电损耗所对应的频率和温度时出现跃迁极化率最大     

用离子束混合及快速热处理方法形成钽的硅化物

本文描述用离子束透过钽金属膜进行混合和快速热处理方法来形成钽的硅化物.用溅射方法在P型硅衬底上淀积一层金属钽,然后用砷离子束透过钽金属模进行混合,采用快速热处理后形成了平整的硅化钽薄层.使用厚度为500埃的钽金属膜,得到钽的硅化物薄层电阻为5.5Ω/□.研究了砷离子能量、剂量及钽膜厚度对钽的硅化物薄层电阻的影响.用透射电镜和台阶仪对所形成的硅化钽进行了分析和厚度测量.     

延长分米波电视发射管使用寿命的探讨（上）

文章从原理上讨论了影响分米波电视发射管寿命的若干因素。并提出了若干延长寿命的建议：（１）正确的灯丝加热方法是行之有效的措施，经验证明：过分强调降低灯丝电压往往得到相反的效果。（２）必须有良好的冷却方式。（３）通过对帘栅电路的分析，说明对此电路必须作很好的处理以消除故障和防止寄生振荡。     

Dehydration and dehydroxylation of reduced charge montmorillonite

Reduced charge montmorillonites (RCM) were prepared by the thermal treatment of lithiumsaturated montmorillonite. Samples prepared by mild thermal treatment with lithium contained more water sorbed than the original montmorrilonite. When RCMs were prepared, part of the lithium cations reacted with hydroxyl groups in the octahedral sheet and released protons, which reacted with the structure. Acid treatment probably enhanced the surface area. which was reflected in the amount of water sorbed. Deprotonation of hydroxyl groups was proved by the measurements of the ignition loss. The heating of lithium saturated montmorillonite at higher temperatures brough about the collapse of the interlayers and a decrease in the amount of water sorbed.